Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM(for LHD without Entry and Start System) › 2015.06–2017.08
RM27T0E _57 Power Source / Network _053729 NETWORKING _0261032 CAN COMMUNICATION SYSTEM(for LHD without Entry and Start System) C

NETWORKING  CAN COMMUNICATION SYSTEM(for LHD without Entry and Start System)  U1110  Lost Communication with Clearance Sonar Module  


DESCRIPTION

DTC Code DTC Detection Condition Trouble Area
U1110 There is no communication from the clearance warning ECU assembly.
·

Power source or inside clearance warning ECU assembly

·

Clearance warning ECU assembly CAN branch wire or connector

·

Clearance warning ECU assembly



For vehicles with a TOYOTA parking assist-sensor system (for 4 sensor type).


WIRING DIAGRAM

C250958E40
5.365,4.027 5.711,4.164 0.346,0.137 10 I1 5.365,4.177 6.929,4.504 1.563,0.327 10 Clearance Warning ECU Assembly 0.41,1.799 2.242,1.937 1.832,0.137 10 G98 1.648,1.365 1.864,1.503 0.216,0.137 10 13 1.648,0.777 1.864,0.914 0.216,0.137 10 2 5.613,1.454 6.098,1.591 0.485,0.137 10 R2 5.388,1.365 5.492,1.503 0.105,0.137 10 5 5.388,0.777 5.492,0.914 0.105,0.137 10 3 5.613,3.074 6.098,3.212 0.485,0.137 10 E 5.613,0.865 6.098,1.003 0.485,0.137 10 R1 5.613,2.477 6.098,2.614 0.485,0.137 10 IG 1.648,2.486 3.001,2.623 1.353,0.137 10 from IG1 NO.1 Relay 5.303,2.986 5.492,3.123 0.188,0.137 10 17 5.303,2.388 5.492,2.525 0.188,0.137 10 15 0.41,1.949 2.409,2.086 1.998,0.137 10 No. 1 Junction Connector 3.761,2.338 4.766,2.476 1.005,0.137 10 ECU-IG NO.2

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


HINT:

Operating the ignition switch, any switches or any doors triggers related ECU and sensor communication with the CAN, which causes resistance variation.


PROCEDURE

1.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL
a.

Disconnect the cable from the negative (-) battery terminal before measuring the resistances of the CAN main wire and the CAN branch wire.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the airbag system.


NOTICE:
·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).

·

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).





NEXT

2.CHECK FOR OPEN IN CAN BUS WIRE (CLEARANCE WARNING ECU ASSEMBLY CAN BRANCH WIRE)
2.CHECK FOR OPEN IN CAN BUS WIRE (CLEARANCE WARNING ECU ASSEMBLY CAN BRANCH WIRE)
a.
U170324E01
0.052,0.057 0.323,0.310 0.272,0.253 10 *a 1.687,0.431 1.822,0.569 0.135,0.137 10 I1 1.123,1.178 0.718,0.855 0.718,0.855 0.563,0.855 false 1.357,1.195 0.998,0.43 0.998,0.43 0.843,0.43 false 0.321,0.778 0.529,0.915 0.208,0.137 10 R1 0.587,0.351 0.795,0.488 0.208,0.137 10 R2

Disconnect the I1 clearance warning ECU assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
I1-3 (R1) - I1-5 (R2) Ignition switch off 54 to 69 Ω


Text in Illustration
*a Front view of wire harness connector
(to Clearance Warning ECU Assembly)



OK

3.CHECK HARNESS AND CONNECTOR (CLEARANCE WARNING ECU ASSEMBLY - BATTERY AND BODY GROUND)

NG

REPAIR OR REPLACE CLEARANCE WARNING ECU ASSEMBLY CAN BRANCH WIRE OR CONNECTOR (R1, R2)

3.CHECK HARNESS AND CONNECTOR (CLEARANCE WARNING ECU ASSEMBLY - BATTERY AND BODY GROUND)
a.
U170325E01
0.052,0.056 0.323,0.309 0.272,0.253 10 *a 1.687,0.43 1.822,0.567 0.135,0.137 10 I1 1.487,1.369 1.267,1.804 1.267,1.804 1.112,1.804 false 1.717,1.369 2.047,1.837 2.047,1.837 2.202,1.837 false 0.879,1.724 1.087,1.862 0.208,0.137 10 IG 2.233,1.759 2.441,1.896 0.208,0.137 10 E

Connect the cable to the negative (-) battery terminal.

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).



b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
I1-17 (E) - Body ground Always Below 1 Ω



c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
I1-15 (IG) - Body ground Ignition switch ON 11 to 14 V



Text in Illustration
*a Front view of wire harness connector
(to Clearance Warning ECU Assembly)


OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR