Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM(for RHD with Entry and Start System) › 2015.06–2017.08
RM27T0E _57 Power Source / Network _053729 NETWORKING _0261033 CAN COMMUNICATION SYSTEM(for RHD with Entry and Start System) U

NETWORKING  CAN COMMUNICATION SYSTEM(for RHD with Entry and Start System)  TERMINALS OF ECU  


HINT:

Operating the engine switch, any switches or any doors triggers related ECU and sensor communication with the CAN, which causes resistance variation.


DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL


a.

Disconnect the cable from the negative (-) battery terminal before measuring the resistances of the CAN main wire and the CAN branch wire.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the airbag system (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>PRECAUTION).


NOTICE:
·

Before measuring the resistance, leave the vehicle for at least 1 minute and do not operate the engine switch, any switches or any doors. If doors need to be opened in order to check connectors, open the doors and leave them open.

·

After turning the engine switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).

·

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).





JUNCTION CONNECTOR


a.

No. 1 Junction Connector

U170121E02
4.104,1.844 4.625,0.979 4.625,0.979 4.688,0.979 true 4.094,2.052 4.625,2.802 4.625,2.802 4.698,2.802 true 4.229,2.063 4.604,2.396 4.604,2.396 4.677,2.396 true 2.979,2.063 2.354,2.375 2.354,2.375 2.281,2.375 true 2.948,1.854 2.375,1.542 2.375,1.542 2.302,1.542 true 4.229,1.854 4.635,1.552 4.635,1.552 4.698,1.552 true 3.219,1.844 2.417,0.427 2.417,0.427 2.354,0.427 true 3.219,2.052 2.406,3.219 2.406,3.219 2.333,3.219 true 3.115,2.063 2.385,2.802 2.385,2.802 2.313,2.802 true 3.094,1.875 2.406,0.979 2.406,0.979 2.344,0.979 true 4.698,0.417 4.625,0.417 4.625,0.417 3.969,1.854 true 3.99,2.073 4.604,3.219 4.604,3.219 4.677,3.219 true 1.75,0.344 2.354,0.521 0.604,0.177 10 false CANH*d 1.75,3.146 2.344,3.323 0.594,0.177 10 false CANL*d 4.729,0.917 5.333,1.094 0.604,0.177 10 false CANH*b 4.729,1.479 5.333,1.656 0.604,0.177 10 false CANH*a 4.729,2.729 5.323,2.896 0.594,0.167 10 false CANL*b 4.729,2.313 5.323,2.49 0.594,0.177 10 false CANL*a 3.427,0.229 3.75,0.406 0.323,0.177 10 false A72 1.75,0.917 2.344,1.083 0.594,0.167 10 false CANH*e 1.75,2.729 2.323,2.917 0.573,0.188 10 false CANL*e 4.729,0.344 5.281,0.521 0.552,0.177 10 false CANH*c 4.729,3.146 5.292,3.313 0.563,0.167 10 false CANL*c 1.75,1.479 2.313,1.656 0.563,0.177 10 false CANH*f 1.75,2.313 2.292,2.479 0.542,0.167 10 false CANL*f

Text in Illustration
*a for No. 4 Junction Connector *b for No. 2 Junction Connector (V2 Bus)
*c for Headlight Swivel ECU Assembly (for LED Headlight) *d for No. 2 Junction Connector (V1 Bus)
*e for Combination Meter Assembly *f for Master Cylinder Solenoid (Skid Control ECU)

No. 1 Junction Connector Wiring Color Connect to
A72-1 (CANH) LG No. 4 junction connector
A72-12 (CANL) W
A72-2 (CANH) GR No. 2 junction connector (V2 bus)
A72-13 (CANL) W
A72-3 (CANH) V Headlight swivel ECU assembly*
A72-14 (CANL) W
A72-9 (CANH) B No. 2 junction connector (V1 bus)
A72-20 (CANL) W
A72-10 (CANH) LG Combination meter assembly
A72-21 (CANL) W
A72-11 (CANH) R Master cylinder solenoid (skid control ECU)
A72-22 (CANL) W

*: for LED Headlight



b.

No. 2 Junction Connector

i.

G132 No. 2 junction connector

U170120E02
3.354,2.063 2.583,2.781 2.583,2.781 2.49,2.781 true 3.344,1.875 2.604,1 2.604,1 2.51,1 true 3.448,2.063 2.583,3.177 2.583,3.177 2.49,3.177 true 3.448,1.865 2.615,0.573 2.615,0.573 2.521,0.573 true 4.615,1.698 4.542,1.698 4.542,1.698 4.229,1.854 true 4.26,2.073 4.563,2.302 4.563,2.302 4.635,2.302 true 4.635,1.24 4.563,1.24 4.563,1.24 4.073,1.854 true 4.094,2.063 4.552,2.677 4.552,2.677 4.635,2.677 true 3.854,2.063 4.531,3.042 4.531,3.042 4.625,3.042 true 3.844,1.854 4.563,0.792 4.563,0.792 4.635,0.792 true 3.219,2.063 2.594,2.365 2.594,2.365 2.5,2.365 true 3.219,1.865 2.615,1.448 2.615,1.448 2.521,1.448 true 3.75,2.042 4.531,3.427 4.531,3.427 4.635,3.427 true 3.719,1.844 4.563,0.323 4.563,0.323 4.635,0.323 true 3.406,0.313 3.802,0.49 0.396,0.177 10 false G132 4.677,2.229 5.229,2.406 0.552,0.177 10 false CANL*a 1.938,0.948 2.479,1.125 0.542,0.177 10 false CANH*f 4.667,1.646 5.24,1.823 0.573,0.177 10 false CANH*a 1.938,2.708 2.469,2.854 0.531,0.146 10 false CANL*f 4.677,0.26 5.25,0.438 0.573,0.177 10 false CANH*d 1.938,0.5 2.51,0.656 0.573,0.156 10 false CANH*e 4.677,3.344 5.229,3.521 0.552,0.177 10 false CANL*d 1.938,3.115 2.49,3.271 0.552,0.156 10 false CANL*e 1.938,1.385 2.51,1.583 0.573,0.198 10 false CANH*g 1.938,2.292 2.51,2.49 0.573,0.198 10 false CANL*g 4.677,2.979 5.219,3.146 0.542,0.167 10 false CANL*c 4.677,0.719 5.229,0.875 0.552,0.156 10 false CANH*c 4.677,1.167 5.25,1.323 0.573,0.156 10 false CANH*b 4.677,2.604 5.229,2.771 0.552,0.167 10 false CANL*b

Text in Illustration
*a for No. 3 Junction Connector *b for Main Body ECU (Multiplex Network Body ECU) (V1 Bus)
*c for DLC3 *d for Center Airbag Sensor Assembly
*e for Spiral Cable Sub-assembly (Steering Angle Sensor) *f for No. 1 Junction Connector
*g
·

for Navigation Receiver Assembly (w/ Navigation System [for Navigation Receiver Type])

·

for Radio and Display Receiver Assembly (w/ Navigation System [for Radio and Display Type] or w/o Navigation System)


- -

No. 2 Junction Connector Wiring Color Connect to
G132-1 (CANH) GR No. 3 junction connector
G132-12 (CANL) W
G132-2 (CANH) L Main body ECU (multiplex network body ECU) (V1 bus)
G132-13 (CANL) W
G132-4 (CANH) R DLC3
G132-15 (CANL) W
G132-5 (CANH) Y Center airbag sensor assembly
G132-16 (CANL) W
G132-7 (CANH) G Spiral cable sub-assembly (steering angle sensor)
G132-18 (CANL) W
G132-8 (CANH) B No. 1 junction connector
G132-19 (CANL) W
G132-9 (CANH) P
·

Navigation receiver assembly*1

·

Radio and display receiver assembly*2


G132-20 (CANL) W

*1: w/ Navigation System (for Navigation Receiver Type)

*2: w/ Navigation System (for Radio and Display Type) or w/o Navigation System



ii.

G95 No. 2 junction connector

U170135E02
4.24,2.073 4.521,2.333 4.521,2.333 4.594,2.333 true 3.594,2.063 2.656,2.5 2.656,2.5 2.583,2.5 true 3.563,1.844 2.646,1.323 2.646,1.323 2.573,1.323 true 4.208,1.854 4.448,1.719 4.448,1.719 4.521,1.719 true 3.719,2.063 2.656,2.802 2.656,2.802 2.583,2.802 true 3.688,1.844 2.667,1.021 2.667,1.021 2.594,1.021 true 4.406,1.458 4.333,1.458 4.333,1.458 4.073,1.844 true 4.094,2.063 4.5,2.552 4.5,2.552 4.573,2.552 true 4.406,1.198 4.344,1.198 4.344,1.198 3.958,1.844 true 3.948,2.063 4.302,2.74 4.302,2.74 4.375,2.74 true 4.229,0.896 4.156,0.896 4.156,0.896 3.833,1.854 true 3.844,2.063 4.146,2.99 4.146,2.99 4.219,2.99 true 4.563,1.656 5.135,1.833 0.573,0.177 10 false CANH*a 4.667,2.26 5.208,2.438 0.542,0.177 10 false CANL*a 3.427,0.5 3.74,0.677 0.313,0.177 10 false G95 2.021,0.927 2.583,1.104 0.563,0.177 10 false CANH*e 2.021,2.729 2.573,2.906 0.552,0.177 10 false CANL*e 2.021,2.406 2.563,2.594 0.542,0.188 10 false CANL*f 2.042,1.25 2.604,1.427 0.563,0.177 10 false CANH*f 4.448,1.385 5.01,1.563 0.563,0.177 10 false CANH*b 4.625,2.479 5.177,2.656 0.552,0.177 10 false CANL*b 4.458,1.125 5.01,1.281 0.552,0.156 10 false CANH*c 4.406,2.667 4.948,2.833 0.542,0.167 10 false CANL*c 4.271,0.813 4.823,0.969 0.552,0.156 10 false CANH*d 4.25,2.906 4.792,3.073 0.542,0.167 10 false CANL*d

Text in Illustration
*a
·

for No. 6 Junction Connector (w/ Blind Spot Monitor System)

·

for No. 3 Junction Connector (w/o Blind Spot Monitor System)


*b for Clearance Warning ECU Assembly (w/ TOYOTA Parking Assist-sensor System [for 4 Sensor Type])
*c for No. 1 Junction Connector *d for Parking Assist ECU (w/ Side Monitor System)
*e for Stabilizer Control ECU (w/ Kinetic Dynamic Suspension System) *f for Seat Belt Control ECU (w/ Pre-crash Safety System)

No. 2 Junction Connector Wiring Color Connect to
G95-1 (CANH) LG
·

No. 6 junction connector*1

·

No. 3 junction connector*2


G95-12 (CANL) W
G95-2 (CANH) R Clearance warning ECU assembly*3
G95-13 (CANL) W
G95-3 (CANH) GR No. 1 junction connector
G95-14 (CANL) W
G95-4 (CANH) B Parking assist ECU*4
G95-15 (CANL) W
G95-5 (CANH) V Stabilizer control ECU*5
G95-16 (CANL) W
G95-6 (CANH) L Seat belt control ECU*6
G95-17 (CANL) W

*1: w/ Blind Spot Monitor System

*2: w/o Blind Spot Monitor System

*3: w/ TOYOTA Parking Assist-sensor System (for 4 Sensor Type)

*4: w/ Side Monitor System

*5: w/ Kinetic Dynamic Suspension System

*6: w/ Pre-crash Safety System



iii.

G133 No. 2 junction connector

U170138E02
2.99,1.094 3.063,1.094 3.063,1.094 3.708,1.854 true 3.719,2.094 3.26,2.615 3.26,2.615 3.177,2.615 true 4.781,1.281 4.719,1.281 4.719,1.281 4.073,1.854 true 4.094,2.063 4.74,2.594 4.74,2.594 4.823,2.594 true 4.781,0.906 4.708,0.906 4.708,0.906 3.948,1.854 true 3.969,2.063 4.729,2.927 4.729,2.927 4.813,2.927 true 4.938,1.552 4.865,1.552 4.865,1.552 4.219,1.865 true 4.219,2.063 4.875,2.313 4.875,2.313 4.958,2.313 true 3.844,2.073 3.281,3.021 3.281,3.021 3.188,3.021 true 3.833,1.844 3.146,0.802 3.146,0.802 3.042,0.802 true 2.573,1.469 2.688,1.469 2.688,1.469 3.583,1.854 true 3.594,2.063 2.76,2.323 2.76,2.323 2.604,2.323 true 4.844,1.208 5.417,1.375 0.573,0.167 10 false CANH*b 4.99,1.49 5.563,1.656 0.573,0.167 10 false CANH*a 4.854,2.865 5.406,3.021 0.552,0.156 10 false CANL*c 4.854,0.802 5.406,0.958 0.552,0.156 10 false CANH*c 4.854,2.521 5.406,2.677 0.552,0.156 10 false CANL*b 4.99,2.25 5.542,2.406 0.552,0.156 10 false CANL*a 3.427,0.604 3.833,0.781 0.406,0.177 10 false G133 2.625,2.542 3.167,2.719 0.542,0.177 10 false CANL*e 2.052,2.26 2.594,2.438 0.542,0.177 10 false CANL*f 2.625,2.948 3.156,3.104 0.531,0.156 10 false CANL*d 2.479,0.698 3.052,0.854 0.573,0.156 10 false CANH*d 2.427,1.021 2.99,1.198 0.563,0.177 10 false CANH*e 2.031,1.406 2.594,1.583 0.563,0.177 10 false CANH*f

Text in Illustration
*a for Rear Television Camera Assembly (w/ Parking Assist Monitor System [for Camera built-in ECU]) *b for Front Power Seat Switch RH (w/ Seat Position Memory)
*c for Multiplex Tilt and Telescopic ECU (for Power Tilt and Power Telescopic Steering Column) *d for Main Body ECU (Multiplex Network Body ECU) (MS Bus)
*e for Driving Support Switch Control ECU (w/ Multi-function Switch) *f for No. 5 Junction Connector

No. 2 Junction Connector Wiring Color Connect to
G133-1 (CANH) B Rear television camera assembly*4
G133-12 (CANL) W
G133-2 (CANH) L Front power seat switch RH*1
G133-13 (CANL) W
G133-3 (CANH) GR Multiplex tilt and telescopic ECU*2
G133-14 (CANL) W
G133-4 (CANH) P Main body ECU (multiplex network body ECU) (MS bus)
G133-15 (CANL) W
G133-5 (CANH) R Driving support switch control ECU*3
G133-16 (CANL) W
G133-6 (CANH) LG No. 5 junction connector
G133-17 (CANL) W

*1: w/ Seat Position Memory

*2: for Power Tilt and Power Telescopic Steering Column

*3: w/ Multi-function Switch

*4: w/ Parking Assist Monitor System (for Camera built-in ECU)




c.

No. 3 Junction Connector

i.

G134 No. 3 junction connector

U170119E02
4.24,2.083 4.667,2.375 4.667,2.375 4.729,2.375 true 3.344,2.052 2.573,2.198 2.573,2.198 2.5,2.198 true 3.313,1.844 2.583,1.594 2.583,1.594 2.521,1.594 true 3.594,2.052 2.552,2.479 2.552,2.479 2.479,2.479 true 3.563,1.844 2.573,1.333 2.573,1.333 2.5,1.333 true 3.844,2.052 2.583,3.063 2.583,3.063 2.51,3.063 true 4.75,1.302 4.688,1.302 4.688,1.302 4.094,1.844 true 4.24,1.854 4.656,1.594 4.656,1.594 4.729,1.594 true 3.813,1.833 2.552,0.76 2.552,0.76 2.479,0.76 true 4.094,2.063 4.667,2.594 4.667,2.594 4.75,2.594 true 3.719,2.052 2.583,2.74 2.583,2.74 2.51,2.74 true 3.688,1.844 2.573,1.031 2.573,1.031 2.5,1.031 true 4.75,1.031 4.677,1.031 4.677,1.031 3.969,1.854 true 3.99,2.052 4.677,2.875 4.677,2.875 4.75,2.875 true 4.792,0.948 5.354,1.125 0.563,0.177 10 false CANH*c 4.792,1.521 5.375,1.698 0.583,0.177 10 false CANH*a 4.792,2.813 5.344,2.969 0.552,0.156 10 false CANL*c 1.938,0.677 2.5,0.844 0.563,0.167 10 false CANH*d 4.792,2.292 5.354,2.469 0.563,0.177 10 false CANL*a 1.948,2.969 2.5,3.156 0.552,0.188 10 false CANL*d 3.385,0.5 3.76,0.677 0.375,0.177 10 false G134 1.969,1.51 2.552,1.688 0.583,0.177 10 false CANH*g 1.948,2.115 2.49,2.292 0.542,0.177 10 false CANL*g 4.792,1.24 5.365,1.396 0.573,0.156 10 false CANH*b 4.792,2.521 5.344,2.688 0.552,0.167 10 false CANL*b 1.958,0.948 2.521,1.125 0.563,0.177 10 false CANH*e 1.948,2.667 2.5,2.844 0.552,0.177 10 false CANL*e 1.979,1.25 2.542,1.427 0.563,0.177 10 false CANH*f 1.948,2.396 2.49,2.573 0.542,0.177 10 false CANL*f

Text in Illustration
*a for No. 2 Junction Connector *b for ECM (V1 Bus)
*c for Four Wheel Drive Control ECU *d for Power Management Control ECU (V1 Bus)
*e for Power Steering ECU Assembly *f for Certification ECU (Smart Key ECU Assembly)
*g for Yaw Rate Sensor Assembly - -

No. 3 Junction Connector Wiring Color Connect to
G134-1 (CANH) GR No. 2 junction connector
G134-12 (CANL) W
G134-2 (CANH) LG ECM (V1 bus)
G134-13 (CANL) W
G134-3 (CANH) G Four wheel drive control ECU
G134-14 (CANL) W
G134-4 (CANH) BR Power management control ECU (V1 bus)
G134-15 (CANL) W
G134-5 (CANH) L Power steering ECU assembly
G134-16 (CANL) W
G134-6 (CANH) P Certification ECU (smart key ECU assembly)
G134-17 (CANL) W
G134-8 (CANH) R Yaw rate sensor assembly
G134-19 (CANL) W


ii.

G98 No. 3 junction connector

U170139E02
2.427,1.135 2.583,1.135 2.583,1.135 3.073,1.854 true 3.104,2.104 2.542,2.792 2.542,2.792 2.417,2.792 true 2.427,0.708 2.583,0.708 2.583,0.708 3.188,1.854 true 2.719,0.281 2.865,0.281 2.865,0.281 3.552,1.854 true 3.208,2.104 2.563,3.198 2.563,3.198 2.438,3.198 true 3.594,2.073 2.833,3.479 2.833,3.479 2.719,3.479 true 2.458,1.542 2.531,1.542 2.531,1.542 2.958,1.865 true 3,2.104 2.51,2.375 2.51,2.375 2.438,2.375 true 4.229,2.094 4.635,2.375 4.635,2.375 4.708,2.375 true 3.844,2.073 4.5,3.229 4.5,3.229 4.583,3.229 true 4.74,1.24 4.677,1.24 4.677,1.24 4.083,1.844 true 4.25,1.865 4.656,1.563 4.656,1.563 4.719,1.563 true 3.833,1.844 4.573,0.583 4.573,0.583 4.74,0.583 true 3.708,1.833 4.396,0.25 4.396,0.25 4.563,0.25 true 4.104,2.104 4.656,2.656 4.656,2.656 4.74,2.656 true 4.729,0.917 4.583,0.917 4.583,0.917 3.958,1.833 true 3.969,2.104 4.625,2.958 4.625,2.958 4.74,2.958 true 3.719,2.073 4.271,3.521 4.271,3.521 4.354,3.521 true 1.875,2.729 2.417,2.885 0.542,0.156 10 false CANL*h 1.885,1.052 2.458,1.219 0.573,0.167 10 false CANH*h 1.875,3.125 2.417,3.302 0.542,0.177 10 false CANL*g 1.885,0.625 2.469,0.802 0.583,0.177 10 false CANH*g 2.177,0.219 2.76,0.396 0.583,0.177 10 false CANH*f 2.156,3.406 2.698,3.583 0.542,0.177 10 false CANL*f 4.792,2.896 5.333,3.073 0.542,0.177 10 false CANL*c 4.792,0.844 5.365,1 0.573,0.156 10 false CANH*c 4.792,1.479 5.365,1.656 0.573,0.177 10 false CANH*a 1.917,1.469 2.49,1.656 0.573,0.188 10 false CANH*i 1.875,2.302 2.427,2.49 0.552,0.188 10 false CANL*i 4.792,1.167 5.354,1.323 0.563,0.156 10 false CANH*b 4.792,2.604 5.333,2.76 0.542,0.156 10 false CANL*b 4.792,2.292 5.344,2.469 0.552,0.177 10 false CANL*a 4.635,3.167 5.198,3.323 0.563,0.156 10 false CANL*d 3.531,0.427 3.917,0.604 0.385,0.177 10 false G98 4.792,0.51 5.365,0.677 0.573,0.167 10 false CANH*d 4.604,0.177 5.177,0.344 0.573,0.167 10 false CANH*e 4.406,3.448 4.969,3.604 0.563,0.156 10 false CANL*e

Text in Illustration
*a
·

for No. 6 Junction Connector (w/ Blind Spot Monitor System)

·

for No. 2 Junction Connector (w/o Blind Spot Monitor System)


*b for Power Management Control ECU (V2 Bus)
*c for Suspension control ECU (w/ Air Suspension System) *d for Driving Support ECU Assembly (w/ Pre-crash Safety System)
*e for Clearance Warning ECU Assembly (w/ TOYOTA Parking Assist-sensor System [for 8 Sensor Type]) *f for Air Conditioning Amplifier Assembly (V2 Bus)
*g for ECM (Power Management Bus) *h for Air Conditioning Amplifier Assembly (Power Management Bus)
*i for Power Management Control ECU (Power Management Bus) - -

No. 3 Junction Connector Wiring Color Connect to
G98-1 (CANH) B
·

No. 6 junction connector*1

·

No. 2 junction connector*2


G98-12 (CANL) W
G98-2 (CANH) V Power management control ECU (V2 bus)
G98-13 (CANL) W
G98-3 (CANH) R Suspension control ECU*3
G98-14 (CANL) W
G98-4 (CANH) G Driving support ECU assembly*4
G98-15 (CANL) W
G98-5 (CANH) L Clearance warning ECU assembly*5
G98-16 (CANL) W
G98-6 (CANH) BR Air conditioning amplifier assembly (V2 bus)
G98-17 (CANL) W
G98-9 (CANH) BR ECM (power management bus)
G98-20 (CANL) GR
G98-10 (CANH) BR Air conditioning amplifier assembly (power management bus)
G98-21 (CANL) Y
G98-11 (CANH) BR Power management control ECU (power management bus)
G98-22 (CANL) W

*1: w/ Blind Spot Monitor System

*2: w/o Blind Spot Monitor System

*3: w/ Air Suspension System

*4: w/ Pre-crash Safety System

*5: w/ TOYOTA Parking Assist-sensor System (for 8 Sensor Type)




d.
U148309E02
2.24,0.229 2.177,0.229 2.177,0.229 1.406,0.854 true 2.542,1.594 2.479,1.594 2.479,1.594 1.792,1.073 true 2.281,0.167 2.938,0.344 0.656,0.177 10 false CANH*a 0.458,0.844 0.854,1.021 0.396,0.177 10 false G102 2.594,1.521 3.156,1.698 0.563,0.177 10 false CANL*a

No. 4 Junction Connector

Text in Illustration
*a for No. 1 Junction Connector

No. 4 Junction Connector Wiring Color Connect to
G102-2 (CANL) W No. 1 junction connector
G102-3 (CANH) LG


e.
U148310E02
2.271,0.229 2.208,0.229 2.208,0.229 1.438,0.854 true 2.542,1.594 2.479,1.594 2.479,1.594 1.792,1.073 true 2.313,0.156 2.969,0.333 0.656,0.177 10 false CANP*a 0.458,0.844 0.854,1.021 0.396,0.177 10 false G103 2.594,1.521 3.156,1.698 0.563,0.177 10 false CANN*a

No. 5 Junction Connector

Text in Illustration
*a for No. 2 Junction Connector

No. 5 Junction Connector Wiring Color Connect to
G103-2 (CANN) W No. 2 junction connector
G103-3 (CANP) LG


f.

NO. 6 JUNCTION CONNECTOR (w/ Blind Spot Monitor System)

U170134E02
4.563,1.708 4.49,1.708 4.49,1.708 4.229,1.854 true 4.229,2.094 4.479,2.219 4.479,2.219 4.563,2.219 true 4.583,1.375 4.51,1.375 4.51,1.375 4.083,1.844 true 4.073,2.073 4.49,2.646 4.49,2.646 4.573,2.646 true 3.969,2.063 4.5,3.031 4.5,3.031 4.604,3.031 true 3.958,1.844 4.5,0.958 4.5,0.958 4.573,0.958 true 3.469,0.458 3.781,0.635 0.313,0.177 10 false R47 4.635,2.146 5.24,2.323 0.604,0.177 10 false CANL*a 4.635,2.563 5.198,2.74 0.563,0.177 10 false CANL*b 4.625,1.292 5.188,1.469 0.563,0.177 10 false CANH*b 4.604,1.635 5.177,1.813 0.573,0.177 10 false CANH*a 4.625,0.885 5.188,1.063 0.563,0.177 10 false CANH*c 4.646,2.969 5.208,3.135 0.563,0.167 10 false CANL*c

Text in Illustration
*a for No. 2 Junction Connector *b for Blind Spot Monitor Sensor LH
*c for No. 3 Junction Connector - -

No. 6 Junction Connector Wiring Color Connect to
R47-1 (CANH) LG No. 2 junction connector
R47-12 (CANL) W
R47-2 (CANH) G Blind spot monitor sensor LH
R47-13 (CANL) W
R47-3 (CANH) B No. 3 junction connector
R47-14 (CANL) W


g.

NO. 7 JUNCTION CONNECTOR (w/ Urea SCR System)

U170476E02
4.563,1.271 4.49,1.271 4.49,1.271 3.844,1.844 true 3.823,2.094 4.49,2.635 4.49,2.635 4.573,2.635 true 4.552,0.938 4.479,0.938 4.479,0.938 3.708,1.844 true 3.719,2.083 4.5,3.083 4.5,3.083 4.583,3.083 true 3.583,2.083 4.479,3.458 4.479,3.458 4.583,3.458 true 3.583,1.854 4.479,0.531 4.479,0.531 4.552,0.531 true 3.448,0.458 3.76,0.635 0.313,0.177 10 false Q41 4.646,2.563 5.25,2.74 0.604,0.177 10 false CANL*a 4.625,3 5.188,3.177 0.563,0.177 10 false CANL*b 4.583,0.844 5.146,1.021 0.563,0.177 10 false CANH*b 4.604,1.198 5.177,1.375 0.573,0.177 10 false CANH*a 4.594,0.448 5.156,0.625 0.563,0.177 10 false CANH*c 4.646,3.375 5.208,3.542 0.563,0.167 10 false CANL*c

Text in Illustration
*a for Urea Pump Control ECU *b for ECM
*c for Nitrogen Oxides Sensor - -

No. 7 Junction Connector Wiring Color Connect to
Q41-4 (CANH) W Urea pump control ECU
Q41-15 (CANL) B
Q41-5 (CANH) L ECM
Q41-16 (CANL) W
Q41-6 (CANH) L Nitrogen oxides sensor
Q41-17 (CANL) W



CHECK DLC3


a.

Disconnect the cable from the negative (-) battery terminal before measuring the resistances of the CAN main wire and the CAN branch wire.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the airbag system.


NOTICE:
·

After turning the engine switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).

·

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).




b.
U149545E03
1.969,0.875 2.073,0.448 2.073,0.448 2.146,0.448 true 1.552,0.875 1.292,0.448 1.292,0.448 1.229,0.448 true 1.938,1.469 1.792,1.844 1.792,1.844 1.729,1.844 true 2.302,1.448 2.365,1.813 2.365,1.813 2.417,1.813 true 0.208,1.146 0.49,1.323 0.281,0.177 10 false G48 2.188,0.365 2.635,0.542 0.448,0.177 10 false CANH 0.979,0.375 1.219,0.531 0.24,0.156 10 false CG 2.458,1.729 2.771,1.906 0.313,0.177 10 false BAT 1.333,1.76 1.719,1.938 0.385,0.177 10 false CANL

Measure the resistance according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Switch Condition Specified Condition
G48-6 (CANH) - G48-14 (CANL) R - W Engine switch off 54 to 69 Ω
G48-6 (CANH) - G48-4 (CG) R - W-B Engine switch off 200 Ω or higher
G48-14 (CANL) - G48-4 (CG) W - W-B Engine switch off 200 Ω or higher
G48-6 (CANH) - G48-16 (BAT) R - GR Engine switch off 6 kΩ or higher
G48-14 (CANL) - G48-16 (BAT) W - GR Engine switch off 6 kΩ or higher



CHECK ECM (for 1GR-FE)


U170144E01
0.235,2.029 0.633,2.167 0.397,0.138 10 BATT 0.99,1.7 0.696,2.096 0.696,2.096 0.604,2.096 false 2.415,1.59 1.957,2.096 1.957,2.096 1.865,2.096 false 4.848,0.507 5.120,0.644 0.272,0.137 10 C36 2.054,0.507 2.340,0.644 0.286,0.137 10 G56 1.13,0.507 1.412,0.644 0.281,0.137 10 G55 1.454,2.032 2.253,2.170 0.799,0.138 10 CANL 2.897,2.087 3.707,2.225 0.811,0.138 10 CANH 2.461,1.686 2.763,2.148 2.763,2.148 2.854,2.148 false 5.791,0.494 6.019,0.663 0.228,0.170 10 E1 5.223,1.328 5.675,0.574 5.675,0.574 5.767,0.574 false

a.

Disconnect the ECM connectors.


b.

Measure the resistance according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Switch Condition Specified Condition
G56-31 (CANH) - G56-25 (CANL) LG - W Engine switch off 108 to 132 Ω
G56-31 (CANH) - C36-12 (E1) LG - BR Engine switch off 200 Ω or higher
G56-25 (CANL) - C36-12 (E1) W - BR Engine switch off 200 Ω or higher
G56-31 (CANH) - G55-24 (BATT) LG - L Engine switch off 6 kΩ or higher
G56-25 (CANL) - G55-24 (BATT) W - L Engine switch off 6 kΩ or higher



CHECK ECM (for 1KD-FTV)


U170143E02
0.46,2.029 0.857,2.167 0.397,0.138 10 BATT 1.214,1.7 0.92,2.096 0.92,2.096 0.829,2.096 false 5.744,0.507 6.016,0.644 0.272,0.137 10 C93 4.792,0.507 5.064,0.644 0.272,0.137 10 C92 2.054,0.507 2.340,0.644 0.286,0.137 10 G58 1.13,0.507 1.412,0.644 0.281,0.137 10 G57 2.051,2.377 2.851,2.516 0.799,0.138 10 CANP*B 1.801,2.605 2.612,2.743 0.811,0.138 10 CANN*B 1.653,1.7 1.932,2.437 1.932,2.437 2.023,2.437 false 1.551,1.7 1.679,2.672 1.679,2.672 1.771,2.672 false 2.261,1.948 3.061,2.086 0.799,0.138 10 CANH*A 2.159,2.175 2.970,2.314 0.811,0.138 10 CANL*A 1.951,1.7 2.142,2.008 2.142,2.008 2.233,2.008 false 1.877,1.7 2.036,2.242 2.036,2.242 2.128,2.242 false 5.033,1.492 4.726,2.032 4.726,2.032 4.635,2.032 false 4.092,1.957 4.891,2.096 0.799,0.138 10 CAN-*C 5.361,1.95 6.172,2.088 0.811,0.138 10 CAN+*C 5.053,1.588 5.239,2.017 5.239,2.017 5.33,2.017 false 6.678,0.747 6.906,0.917 0.228,0.170 10 E1 6.251,1.176 6.562,0.828 6.562,0.828 6.654,0.828 false

Text in Illustration
*A for V1 Bus *B for Power Management Bus
*C for Powertrain Bus - -

a.

Disconnect the ECM connectors.


b.

Measure the resistance according to the value(s) in the table below.

for V1 Bus
Terminal No. (Symbol) Wiring Color Switch Condition Specified Condition
G58-35 (CANH) - G58-36 (CANL) LG - W Engine switch off 108 to 132 Ω
G58-35 (CANH) - C93-1 (E1) LG - BR Engine switch off 200 Ω or higher
G58-36 (CANL) - C93-1 (E1) W - BR Engine switch off 200 Ω or higher
G58-35 (CANH) - G57-23 (BATT) LG - L Engine switch off 6 kΩ or higher
G58-36 (CANL) - G57-23 (BATT) W - L Engine switch off 6 kΩ or higher

for Power Management Bus
Terminal No. (Symbol) Wiring Color Switch Condition Specified Condition
G57-20 (CANP) - G57-21 (CANN) BR - GR Engine switch off 108 to 132 Ω
G57-20 (CANP) - C93-1 (E1) BR - BR Engine switch off 200 Ω or higher
G57-21 (CANN) - C93-1 (E1) GR - BR Engine switch off 200 Ω or higher
G57-20 (CANP) - G57-23 (BATT) BR - L Engine switch off 6 kΩ or higher
G57-21 (CANN) - G57-23 (BATT) GR - L Engine switch off 6 kΩ or higher

for Powertrain Bus
Terminal No. (Symbol) Wiring Color Switch Condition Specified Condition
C92-24 (CAN+) - C92-18 (CAN-) B - W Engine switch off 108 to 132 Ω
C92-24 (CAN+) - C93-1 (E1) B - BR Engine switch off 200 Ω or higher
C92-18 (CAN-) - C93-1 (E1) W - BR Engine switch off 200 Ω or higher
C92-24 (CAN+) - G57-23 (BATT) B - L Engine switch off 6 kΩ or higher
C92-18 (CAN-) - G57-23 (BATT) W - L Engine switch off 6 kΩ or higher



CHECK ECM (for 1GD-FTV)


U170469E02
6.667,1.771 6.729,1.771 6.729,1.771 6.854,1.052 true 4.073,1.76 4.135,1.76 4.135,1.76 4.656,1.042 true 5.813,1.302 6.073,2.104 6.073,2.104 6.156,2.104 true 5.802,1.406 5.917,2.406 5.917,2.406 5.99,2.406 true 4.396,2.448 4.448,2.448 4.448,2.448 4.781,1.438 true 4.219,2.094 4.271,2.094 4.271,2.094 4.781,1.281 true 0.604,0.375 1,0.552 0.396,0.177 10 false C149 1.76,0.385 2.125,0.563 0.365,0.177 10 false C150 2.969,0.375 3.344,0.552 0.375,0.177 10 false C151 4.042,0.375 4.427,0.552 0.385,0.177 10 false C152 5.146,0.365 5.521,0.542 0.375,0.177 10 false G184 6.24,0.375 6.615,0.552 0.375,0.177 10 false G185 6.063,2.323 6.667,2.5 0.604,0.177 10 false CANL*A 3.635,2.01 4.198,2.188 0.563,0.177 10 false CANU*B 3.833,2.365 4.396,2.542 0.563,0.177 10 false CAND*B 6.313,1.698 6.729,1.875 0.417,0.177 10 false BATT 6.188,2.021 6.75,2.198 0.563,0.177 10 false CANH*A 3.813,1.708 4.063,1.875 0.25,0.167 10 false E1

Text in Illustration
*A for V1 Bus *B for Local Bus

a.

Disconnect the ECM connectors.


b.

Measure the resistance according to the value(s) in the table below.

for V1 Bus
Terminal No. (Symbol) Wiring Color Switch Condition Specified Condition
G184-17 (CANH) - G184-28 (CANL) LG - W Engine switch off 108 to 132 Ω
G184-17 (CANH) - C152-1 (E1) LG - W-B Engine switch off 200 Ω or higher
G184-28 (CANL) - C152-1 (E1) W - W-B Engine switch off 200 Ω or higher
G184-17 (CANH) - G185-1 (BATT) LG - L Engine switch off 6 kΩ or higher
G184-28 (CANL) - G185-1 (BATT) W - L Engine switch off 6 kΩ or higher

for Local Bus
Terminal No. (Symbol) Wiring Color Switch Condition Specified Condition
G184-27 (CANU) - G184-35 (CAND) L - W Engine switch off 108 to 132 Ω
G184-27 (CANU) - C152-1 (E1) L - W-B Engine switch off 200 Ω or higher
G184-35 (CAND) - C152-1 (E1) W - W-B Engine switch off 200 Ω or higher
G184-27 (CANU) - G185-1 (BATT) L - L Engine switch off 6 kΩ or higher
G184-35 (CAND) - G185-1 (BATT) W - L Engine switch off 6 kΩ or higher



CHECK DRIVER SIDE JUNCTION BLOCK ASSEMBLY, MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)


U169736E02
1.625,1.531 1.823,1.292 1.823,1.292 1.906,1.292 false 1.625,1.854 1.823,1.698 1.823,1.698 1.906,1.698 false 1.625,2.188 1.823,2.385 1.823,2.385 1.906,2.385 false 5.031,8.135 5.281,7.708 5.281,7.708 5.385,7.708 true 3.031,8.135 2.781,7.708 2.781,7.708 2.677,7.708 true 3.573,4.604 3.427,5.156 3.427,5.156 3.344,5.156 true 3.49,4.604 3.344,4.979 3.344,4.979 3.26,4.979 true 1.365,4.615 1.51,5.167 1.51,5.167 1.594,5.167 true 1.438,4.594 1.594,4.958 1.594,4.958 1.677,4.958 true 1.615,1.031 1.615,0.615 1.615,0.615 1.76,0.615 false 0.896,1.635 1.104,1.792 0.208,0.156 10 false 2H 3.594,3.896 3.875,4.052 0.281,0.156 10 false G64 0.896,2.229 1.104,2.385 0.208,0.156 10 false 2F 5.865,1.552 6.073,1.708 0.208,0.156 10 false 2D 5.865,2.26 6.073,2.417 0.208,0.156 10 false 2A 1.073,2.771 1.281,2.927 0.208,0.156 10 false 2K 3.75,1.354 3.865,1.5 0.115,0.146 10 false A 1.927,1.219 2.302,1.365 0.375,0.146 10 false G65 1.792,0.552 2.167,0.698 0.375,0.146 10 false *1 1.927,2.313 2.271,2.458 0.344,0.146 10 false G63 1.927,1.646 2.323,1.792 0.396,0.146 10 false G64 1.094,3.896 1.375,4.052 0.281,0.156 10 false G63 1.125,5.198 1.344,5.354 0.219,0.156 10 false 2H 1.885,6.438 2.104,6.594 0.219,0.156 10 false 2D 4.938,6.438 5.156,6.594 0.219,0.156 10 false 2A 3.51,7.708 3.646,7.865 0.135,0.156 10 false A 3.948,5.208 4.146,5.365 0.198,0.156 10 false 2F 5.896,5.208 6.094,5.365 0.198,0.156 10 false 2K 5.906,3.896 6.188,4.052 0.281,0.156 10 false G65 5.417,7.646 5.833,7.802 0.417,0.156 10 false BECU 2.281,7.646 2.698,7.802 0.417,0.156 10 false GND1 2.813,5.083 3.365,5.24 0.552,0.156 10 false CANL*A 2.708,4.896 3.302,5.052 0.594,0.156 10 false CANH*A 1.719,4.885 2.302,5.042 0.583,0.156 10 false CANP*B 1.635,5.094 2.25,5.25 0.615,0.156 10 false CANN*B

Text in Illustration
*A for V1 Bus *B for MS Bus
*1 Main Body ECU (Multiplex Network Body ECU) - -

a.

Remove the main body ECU (multiplex network body ECU) (See page Power Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>REMOVAL).


b.

Measure the resistance according to the value(s) in the table below.

for V1 Bus
Terminal No. (Symbol) Wiring Color Switch Condition Specified Condition
G64-14 (CANH) - G64-13 (CANL) L - W Engine switch off 54 to 69 Ω
G64-14 (CANH) - A-11 (GND1) L - None Engine switch off 200 Ω or higher
G64-13 (CANL) - A-11 (GND1) W - None Engine switch off 200 Ω or higher
G64-14 (CANH) - A-30 (BECU) L - None Engine switch off 6 kΩ or higher
G64-13 (CANL) - A-30 (BECU) W - None Engine switch off 6 kΩ or higher

for MS Bus
Terminal No. (Symbol) Wiring Color Switch Condition Specified Condition
G63-9 (CANP) - G63-10 (CANN) P - W Engine switch off 108 to 132 Ω
G63-9 (CANP) - A-11 (GND1) P - None Engine switch off 200 Ω or higher
G63-10 (CANN) - A-11 (GND1) W - None Engine switch off 200 Ω or higher
G63-9 (CANP) - A-30 (BECU) P - None Engine switch off 6 kΩ or higher
G63-10 (CANN) - A-30 (BECU) W - None Engine switch off 6 kΩ or higher



CHECK COMBINATION METER ASSEMBLY


U149211E03
4.719,1.188 4.927,0.969 4.927,0.969 5.01,0.969 true 4.125,1.135 4.25,0.344 4.25,0.344 4.333,0.344 true 2.448,1.177 2.188,1.365 2.188,1.365 2.063,1.365 true 2.552,1.198 2.323,1.625 2.323,1.625 2.198,1.625 true 3.458,0.333 3.729,0.5 0.271,0.167 10 false G6 5.052,0.885 5.313,1.073 0.26,0.188 10 false E2 4.375,0.26 4.51,0.448 0.135,0.188 10 false B 1.646,1.271 2.063,1.438 0.417,0.167 10 false CANH 1.844,1.542 2.271,1.698 0.427,0.156 10 false CANL

a.

Disconnect the combination meter assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Switch Condition Specified Condition
G6-40 (CANH) - G6-39 (CANL) LG - W Engine switch off 108 to 132 Ω
G6-40 (CANH) - G6-21 (E2) LG - BR Engine switch off 200 Ω or higher
G6-39 (CANL) - G6-21 (E2) W - BR Engine switch off 200 Ω or higher
G6-40 (CANH) - G6-26 (B) LG - L Engine switch off 6 kΩ or higher
G6-39 (CANL) - G6-26 (B) W - L Engine switch off 6 kΩ or higher



CHECK POWER STEERING ECU ASSEMBLY


U148691E03
2.125,1.052 2.344,0.458 2.344,0.458 2.469,0.458 true 2.292,1.073 2.646,0.698 2.646,0.698 2.75,0.698 true 5.75,1.26 5.958,1.385 5.958,1.385 6.063,1.385 true 1.75,0.469 1.833,0.469 1.833,0.469 1.958,1.063 true 0.427,0.938 0.781,1.125 0.354,0.188 10 false G46 2.792,0.615 3.229,0.844 0.438,0.229 10 false CANH 2.5,0.396 2.906,0.625 0.406,0.229 10 false CANL 1.417,0.385 1.76,0.573 0.344,0.188 10 false GND 6.115,1.302 6.521,1.531 0.406,0.229 10 false BAT 3.979,1.01 4.333,1.198 0.354,0.188 10 false G48

a.

Disconnect the power steering ECU assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Switch Condition Specified Condition
G46-1 (CANH) - G46-2 (CANL) L - W Engine switch off 54 to 69 Ω
G46-1 (CANH) - G46-3 (GND) L - W-B Engine switch off 200 Ω or higher
G46-2 (CANL) - G46-3 (GND) W - W-B Engine switch off 200 Ω or higher
G46-1 (CANH) - G48-16 (BAT) L - GR Engine switch off 6 kΩ or higher
G46-2 (CANL) - G48-16 (BAT) W - GR Engine switch off 6 kΩ or higher



CHECK AIR CONDITIONING AMPLIFIER ASSEMBLY


E346813E01
1.635,0.292 2.052,0.542 0.417,0.25 3.865,0.302 4.281,0.552 0.417,0.25 5.49,0.302 5.906,0.552 0.417,0.25 3.615,1.135 3.271,0.563 3.271,0.563 3.104,0.563 true 3.875,1.135 3.333,0.333 3.333,0.333 3.167,0.333 true 3.99,1.146 3.479,0.094 3.479,0.094 3.313,0.094 true 5.219,1.281 4.792,0.281 4.792,0.281 4.625,0.281 true 1.719,0.333 2.177,0.531 0.458,0.198 10 false G24 3.938,0.344 4.396,0.542 0.458,0.198 10 false G25 5.615,0.354 6.073,0.552 0.458,0.198 10 false z1 2.771,0.49 3.229,0.688 0.458,0.198 10 false GND 2.781,0.24 3.24,0.438 0.458,0.198 10 false CANL 2.896,0.021 3.354,0.219 0.458,0.198 10 false CANH 4.49,0.198 4.948,0.396 0.458,0.198 10 false B

a.

Disconnect the air conditioning amplifier assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Condition Specified Condition
G25-11 (CANH) - G25-12 (CANL) BR - Y*1
BR - W*2
Engine switch off 54 to 69 Ω
G25-11 (CANH) - G25-14 (GND) BR - W-B Engine switch off 200 Ω or higher
G25-12 (CANL) - G25-14 (GND) Y - W-B*1
W - W-B*2
Engine switch off 200 Ω or higher
G25-11 (CANH) - G25-21 (B) BR - V Engine switch off 6 kΩ or higher
G25-12 (CANL) - G25-21 (B) Y - V*1
W - V*2
Engine switch off 6 kΩ or higher

*1: for 1KD-FTV

*2: for 1GR-FE, 1GD-FTV




CHECK CENTER AIRBAG SENSOR ASSEMBLY


U148296E01
1.332,0.448 1.613,0.660 0.281,0.212 10 G1 5.451,0.504 5.746,0.716 0.295,0.212 10 G48 2.157,0.654 2.600,0.800 0.443,0.147 10 CANH 2.191,2.133 2.634,2.279 0.443,0.147 10 CANL 1.837,1.377 2.076,0.727 2.076,0.727 2.127,0.727 false 1.079,2.119 1.271,2.265 0.193,0.147 10 E1 6.117,1.693 6.319,2.04 6.319,2.04 6.401,2.04 false 6.412,1.979 6.725,2.126 0.313,0.147 10 BAT 1.978,1.843 2.101,2.197 2.101,2.197 2.164,2.197 false 1.46,1.833 1.338,2.192 1.338,2.192 1.275,2.192 false

a.

Disconnect the center airbag sensor assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Switch Condition Specified Condition
G1-13 (CANH) - G1-22 (CANL) Y - W Engine switch off 54 to 69 Ω
G1-13 (CANH) - G1-25 (E1) Y - W-B Engine switch off 200 Ω or higher
G1-22 (CANL) - G1-25 (E1) W - W-B Engine switch off 200 Ω or higher
G1-13 (CANH) - G48-16 (BAT) Y - GR Engine switch off 6 kΩ or higher
G1-22 (CANL) - G48-16 (BAT) W - GR Engine switch off 6 kΩ or higher



CHECK MASTER CYLINDER SOLENOID (SKID CONTROL ECU)


U170045E02
2.198,0.667 2.365,0.208 2.365,0.208 2.458,0.208 true 2.188,0.958 2.448,1.625 2.448,1.625 2.542,1.625 true 3.896,0.698 3.719,0.24 3.719,0.24 3.615,0.24 true 4.26,0.677 4.438,0.281 4.438,0.281 4.542,0.281 true 2.594,1.552 3.021,1.719 0.427,0.167 10 false CANL 2.5,0.125 2.927,0.292 0.427,0.167 10 false CANH 3.229,0.156 3.625,0.323 0.396,0.167 10 false +BM1 4.583,0.219 5.031,0.385 0.448,0.167 10 false GND1 4.958,0.844 5.25,1.01 0.292,0.167 10 false A8 0.49,0.854 0.781,1.021 0.292,0.167 10 false A7

a.

Disconnect the master cylinder solenoid (skid control ECU) connector.


b.

Measure the resistance according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Switch Condition Specified Condition
A7-11 (CANH) - A7-25 (CANL) R - W Engine switch off 54 to 69 Ω
A7-11 (CANH) - A7-1 (GND1) R - W-B Engine switch off 200 Ω or higher
A7-25 (CANL) - A7-1 (GND1) W - W-B Engine switch off 200 Ω or higher
A7-11 (CANH) - A7-2 (+BM1) R - B Engine switch off 6 kΩ or higher
A7-25 (CANL) - A7-2 (+BM1) W - B Engine switch off 6 kΩ or higher



CHECK SPIRAL CABLE SUB-ASSEMBLY (STEERING ANGLE SENSOR)


U148274E03
2.25,1.177 2.583,0.583 2.583,0.583 2.667,0.583 true 1.958,1.167 1.625,0.573 1.625,0.573 1.531,0.573 true 2.365,1.198 2.698,0.833 2.698,0.833 2.781,0.833 true 2.156,1.167 2.354,0.375 2.354,0.375 2.448,0.375 true 2.719,0.5 3.146,0.667 0.427,0.167 10 false CANL 1.26,0.49 1.573,0.656 0.313,0.167 10 false BAT 2.865,1.083 3.177,1.25 0.313,0.167 10 false G33 2.813,0.76 3.125,0.938 0.313,0.177 10 false ESS 2.5,0.302 2.948,0.469 0.448,0.167 10 false CANH

a.

Disconnect the spiral cable sub-assembly (steering angle sensor) connector.


b.

Measure the resistance according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Switch Condition Specified Condition
G33-4 (CANH) - G33-3 (CANL) G - W Engine switch off 54 to 69 Ω
G33-4 (CANH) - G33-2 (ESS) G - W-B Engine switch off 200 Ω or higher
G33-3 (CANL) - G33-2 (ESS) W - W-B Engine switch off 200 Ω or higher
G33-4 (CANH) - G33-6 (BAT) G - L Engine switch off 6 kΩ or higher
G33-3 (CANL) - G33-6 (BAT) W - L Engine switch off 6 kΩ or higher



CHECK YAW RATE SENSOR ASSEMBLY


U148362E01
2.055,0.276 2.350,0.422 0.295,0.147 10 G52 5.008,0.276 5.303,0.422 0.295,0.147 10 G48 2.571,1.585 2.990,1.769 0.419,0.184 10 CANL 1.461,1.474 1.884,1.658 0.422,0.184 10 CANH 2.333,0.846 2.442,1.659 2.442,1.659 2.555,1.659 false 2.23,0.846 1.968,1.54 1.968,1.54 1.879,1.54 false 3.034,1.47 3.372,1.644 0.338,0.174 10 GND 2.442,0.835 2.918,1.536 2.918,1.536 3.014,1.536 false 5.988,1.555 6.275,1.729 0.287,0.174 10 BAT 5.661,1.298 5.868,1.626 5.868,1.626 5.97,1.626 false

a.

Disconnect the yaw rate sensor assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Switch Condition Specified Condition
G52-3 (CANH) - G52-2 (CANL) R - W Engine switch off 54 to 69 Ω
G52-3 (CANH) - G52-1 (GND) R - W-B Engine switch off 200 Ω or higher
G52-2 (CANL) - G52-1 (GND) W - W-B Engine switch off 200 Ω or higher
G52-3 (CANH) - G48-16 (BAT) R - GR Engine switch off 6 kΩ or higher
G52-2 (CANL) - G48-16 (BAT) W - GR Engine switch off 6 kΩ or higher



CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)


U169640E01
4.613,0.631 4.914,0.812 0.301,0.181 10 G39 2.399,0.631 2.700,0.812 0.301,0.181 10 G38 4.214,0.44 4.657,0.621 0.443,0.181 10 +B 0.888,0.501 1.288,0.682 0.400,0.181 10 CANL 1.115,0.295 1.551,0.477 0.436,0.181 10 CANH 0.726,1.76 0.881,1.911 0.155,0.151 10 E 3.696,1.279 4.079,0.515 4.079,0.515 4.177,0.515 false 2.101,1.273 1.659,0.371 1.659,0.371 1.547,0.371 false 1.993,1.291 1.403,0.573 1.403,0.573 1.282,0.573 false 1.39,1.334 0.972,1.828 0.972,1.828 0.874,1.828 false

a.

Disconnect the certification ECU (smart key ECU assembly) connector.


b.

Measure the resistance according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Switch Condition Specified Condition
G38-9 (CANH) - G38-10 (CANL) P - W Engine switch off 54 to 69 Ω
G38-9 (CANH) - G38-15 (E) P - W-B Engine switch off 200 Ω or higher
G38-10 (CANL) - G38-15 (E) W - W-B Engine switch off 200 Ω or higher
G38-9 (CANH) - G38-1 (+B) P - V Engine switch off 6 kΩ or higher
G38-10 (CANL) - G38-1 (+B) W - V Engine switch off 6 kΩ or higher



CHECK POWER MANAGEMENT CONTROL ECU


U169942E01
5.222,1.467 5.519,1.653 0.297,0.186 10 G51 5.163,0.967 5.572,1.125 0.408,0.158 10 AM22 3.115,0.981 3.458,1.140 0.343,0.158 10 GND 3.544,2.396 4.089,2.555 0.544,0.158 10 CA2L*C 3.395,2.205 3.979,2.363 0.584,0.158 10 CA2H*C 4.119,1.681 4.005,2.268 4.005,2.268 3.931,2.268 false 4.076,2.472 4.164,2.472 4.164,2.472 4.194,1.68 false 3.544,0.62 4.078,0.779 0.535,0.158 10 CA1L*A 4.536,0.62 5.564,0.779 1.028,0.158 10 CA3P*B, *C 3.334,0.805 3.869,0.963 0.534,0.158 10 CA1H*A 4.741,0.805 5.813,0.963 1.071,0.158 10 CA3N*B, *C 4.849,1.394 5.062,1.039 5.062,1.039 5.156,1.039 false 3.729,1.394 3.541,1.053 3.541,1.053 3.448,1.053 false 4.123,1.548 3.937,0.868 3.937,0.868 3.863,0.868 false 4.066,0.696 4.154,0.696 4.154,0.696 4.198,1.546 false 4.458,1.548 4.639,0.868 4.639,0.868 4.713,0.868 false 4.514,0.696 4.427,0.696 4.427,0.696 4.382,1.546 false

Text in Illustration
*A for V1 Bus *B for Power Management Bus
*C for V2 Bus - -

a.

Disconnect the power management control ECU connector.


b.

Measure the resistance according to the value(s) in the table below.

for V1 Bus
Terminal No. (Symbol) Wiring Color Switch Condition Specified Condition
G51-14 (CA1H) - G51-13 (CA1L) BR - W Engine switch off 54 to 69 Ω
G51-14 (CA1H) - G51-6 (GND) BR - W-B Engine switch off 200 Ω or higher
G51-13 (CA1L) - G51-6 (GND) W - W-B Engine switch off 200 Ω or higher
G51-14 (CA1H) - G51-1 (AM22) BR - B Engine switch off 6 kΩ or higher
G51-13 (CA1L) - G51-1 (AM22) W - B Engine switch off 6 kΩ or higher

for V2 Bus (for 1KD-FTV)
Terminal No. (Symbol) Wiring Color Switch Condition Specified Condition
G51-26 (CA2H) - G51-25 (CA2L) V - W Engine switch off 108 to 132 Ω
G51-26 (CA2H) - G51-6 (GND) V - W-B Engine switch off 200 Ω or higher
G51-25 (CA2L) - G51-6 (GND) W - W-B Engine switch off 200 Ω or higher
G51-26 (CA2H) - G51-1 (AM22) V - B Engine switch off 6 kΩ or higher
G51-25 (CA2L) - G51-1 (AM22) W - B Engine switch off 6 kΩ or higher

for V2 Bus (for 1GR-FE, 1GD-FTV), Power Management Bus
Terminal No. (Symbol) Wiring Color Switch Condition Specified Condition
G51-12 (CA3P) - G51-11 (CA3N) BR - W*1
V - W*2
Engine switch off 108 to 132 Ω
G51-12 (CA3P) - G51-6 (GND) BR - W-B*1
V - W-B*2
Engine switch off 200 Ω or higher
G51-11 (CA3N) - G51-6 (GND) W - W-B Engine switch off 200 Ω or higher
G51-12 (CA3P) - G51-1 (AM22) BR - B*1
V - B*2
Engine switch off 6 kΩ or higher
G51-11 (CA3N) - G51-1 (AM22) W - B Engine switch off 6 kΩ or higher

*1: for 1KD-FTV

*2: for 1GR-FE, 1GD-FTV




CHECK NAVIGATION RECEIVER ASSEMBLY (w/ Navigation System [for Navigation Receiver Type])


U170731E01
0.886,1.832 1.158,2.014 0.272,0.181 10 H54 3.355,0.518 3.627,0.699 0.272,0.181 10 H56 0.225,1.915 0.603,2.064 0.378,0.148 10 +B1 1.299,3.018 1.739,3.166 0.439,0.148 10 GND1 3.614,1.475 4.053,1.624 0.439,0.148 10 CANH 2.629,1.475 3.068,1.624 0.439,0.148 10 CANL 0.646,2.379 0.585,1.972 0.585,1.972 0.495,1.972 false 1.096,2.682 1.172,3.075 1.172,3.075 1.262,3.075 false 3.358,1.12 3.486,1.537 3.486,1.537 3.59,1.537 false 3.263,1.12 3.136,1.537 3.136,1.537 3.032,1.537 false

a.

Disconnect the navigation receiver assembly connectors.


b.

Measure the resistance according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Switch Condition Specified Condition
H56-9 (CANH) - H56-10 (CANL) W - P Engine switch off 54 to 69 Ω
H56-9 (CANH) - H54-7 (GND1) W - BR Engine switch off 200 Ω or higher
H56-10 (CANL) - H54-7 (GND1) P - BR Engine switch off 200 Ω or higher
H56-9 (CANH) - H54-4 (+B1) W - R Engine switch off 6 kΩ or higher
H56-10 (CANL) - H54-4 (+B1) P - R Engine switch off 6 kΩ or higher



CHECK RADIO AND DISPLAY RECEIVER ASSEMBLY (w/ Navigation System [for Radio and Display Type] or w/o Navigation System)


U170697E01
4.291,0.927 4.564,1.069 0.274,0.142 10 H51 0.834,1.791 1.112,1.933 0.278,0.142 10 H49 4.304,1.501 4.016,0.931 4.016,0.931 3.81,0.931 false 3.754,1.118 3.89,1.118 3.89,1.118 4.191,1.493 false 3.359,0.866 3.807,1.008 0.448,0.142 10 CANH 3.35,1.053 3.798,1.195 0.448,0.142 10 CANL 1.09,2.623 1.192,2.963 1.192,2.963 1.299,2.963 false 0.34,2.052 0.406,2.052 0.406,2.052 0.572,2.35 false 0.048,1.987 0.426,2.129 0.378,0.142 10 +B1 1.333,2.891 1.780,3.033 0.448,0.142 10 GND1

a.

Disconnect the radio and display receiver assembly connectors.


b.

Measure the resistance according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Switch Condition Specified Condition
H51-9 (CANH) - H51-10 (CANL) W - P Engine switch off 54 to 69 Ω
H51-9 (CANH) - H49-7 (GND1) W - BR Engine switch off 200 Ω or higher
H51-10 (CANL) - H49-7 (GND1) P - BR Engine switch off 200 Ω or higher
H51-9 (CANH) - H49-4 (+B1) W - R Engine switch off 6 kΩ or higher
H51-10 (CANL) - H49-4 (+B1) P - R Engine switch off 6 kΩ or higher



CHECK FOUR WHEEL DRIVE CONTROL ECU


U148363E03
0.906,0.813 0.854,0.354 0.854,0.354 0.771,0.354 true 0.823,0.844 0.688,0.573 0.688,0.573 0.604,0.573 true 2.521,0.802 2.396,0.448 2.396,0.448 2.313,0.448 true 5.781,1.104 5.906,1.344 5.906,1.344 6,1.344 true 1.979,0.385 2.313,0.573 0.333,0.188 10 false GND 2.677,0.354 2.99,0.563 0.313,0.208 10 false G54 0.344,0.281 0.76,0.469 0.417,0.188 10 false CANH 0.219,0.5 0.615,0.688 0.396,0.188 10 false CANL 1.427,0.344 1.781,0.521 0.354,0.177 10 false G53 4.052,0.844 4.365,1.052 0.313,0.208 10 false G48 6.042,1.271 6.333,1.458 0.292,0.188 10 false BAT

a.

Disconnect the four wheel drive control ECU connectors.


b.

Measure the resistance according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Switch Condition Specified Condition
G53-19 (CANH) - G53-20 (CANL) G - W Engine switch off 54 to 69 Ω
G53-19 (CANH) - G54-4 (GND) G - W-B Engine switch off 200 Ω or higher
G53-20 (CANL) - G54-4 (GND) W - W-B Engine switch off 200 Ω or higher
G53-19 (CANH) - G48-16 (BAT) G - GR Engine switch off 6 kΩ or higher
G53-20 (CANL) - G48-16 (BAT) W - GR Engine switch off 6 kΩ or higher



CHECK SUSPENSION CONTROL ECU (w/ Air Suspension System)


E346814E01
1.938,0.271 2.365,0.49 0.427,0.219 3.375,0.271 3.802,0.49 0.427,0.219 4.833,0.271 5.26,0.49 0.427,0.219 4.667,0.906 4.667,0.323 4.667,0.323 4.5,0.323 true 5.167,0.917 5.583,0.25 5.583,0.25 5.75,0.25 true 5.625,1.104 6.042,0.438 6.042,0.438 6.208,0.438 true 5.5,1.167 6,1.417 6,1.417 6.25,1.417 true 2.021,0.292 2.479,0.49 0.458,0.198 10 false R19 3.479,0.302 3.938,0.5 0.458,0.198 10 false A14 4.927,0.302 5.385,0.5 0.458,0.198 10 false A49 4.177,0.24 4.635,0.438 0.458,0.198 10 false GND 5.813,0.167 6.271,0.365 0.458,0.198 10 false B 6.26,0.344 6.719,0.542 0.458,0.198 10 false CANH 6.302,1.333 6.76,1.531 0.458,0.198 10 false CANL

a.

Disconnect the suspension control ECU connector.


b.

Measure the resistance according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Switch Condition Specified Condition
A49-7 (CANH) - A49-8 (CANL) R - W Engine switch off 54 to 69 Ω
A49-7 (CANH) - A49-5 (GND) R - W-B Engine switch off 200 Ω or higher
A49-8 (CANL) - A49-5 (GND) W - W-B Engine switch off 200 Ω or higher
A49-7 (CANH) - A49-3 (B) R - GR Engine switch off 6 kΩ or higher
A49-8 (CANL) - A49-3 (B) W - GR Engine switch off 6 kΩ or higher



CHECK STABILIZER CONTROL ECU (w/ Kinetic Dynamic Suspension System)


U148404E01
2.081,0.146 2.453,0.315 0.372,0.169 10 G123 5.615,0.146 5.909,0.359 0.295,0.212 10 G48 6.28,1.097 6.482,1.444 6.482,1.444 6.564,1.444 false 6.575,1.384 6.888,1.530 0.313,0.147 10 BAT 1.834,1.004 2.034,1.459 2.034,1.459 2.115,1.459 false 2.126,1.398 2.528,1.545 0.402,0.147 10 CANL 1.745,1.022 1.879,1.652 1.879,1.652 1.961,1.652 false 1.972,1.591 2.396,1.738 0.424,0.147 10 CANH 2.359,0.933 2.559,0.478 2.559,0.478 2.641,0.478 false 2.657,0.41 2.985,0.556 0.327,0.147 10 GND

a.

Disconnect the stabilizer control ECU connector.


b.

Measure the resistance according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Switch Condition Specified Condition
G123-29 (CANH) - G123-28 (CANL) V - W Engine switch off 54 to 69 Ω
G123-29 (CANH) - G123-22 (GND) V - W-B Engine switch off 200 Ω or higher
G123-28 (CANL) - G123-22 (GND) W - W-B Engine switch off 200 Ω or higher
G123-29 (CANH) - G48-16 (BAT) V - GR Engine switch off 6 kΩ or higher
G123-28 (CANL) - G48-16 (BAT) W - GR Engine switch off 6 kΩ or higher



CHECK SEAT BELT CONTROL ECU (w/ Pre-crash Safety System)


U170572E01
4.535,0.587 4.937,0.737 0.402,0.150 10 G118 2.82,0.588 3.197,0.738 0.377,0.150 10 G117 5.749,0.718 6.205,0.868 0.456,0.150 10 CANH 5.394,0.289 5.850,0.439 0.456,0.150 10 CANL 4.789,1.697 5.178,0.358 5.178,0.358 5.346,0.358 false 4.929,1.725 5.547,0.797 5.547,0.797 5.715,0.797 false 2.087,0.367 2.304,0.517 0.217,0.150 10 +B 1.415,0.63 1.870,0.780 0.456,0.150 10 PGND 3.142,1.651 2.484,0.434 2.484,0.434 2.316,0.434 false 2.834,1.665 2.014,0.695 2.014,0.695 1.846,0.695 false

a.

Disconnect the seat belt control ECU connectors.


b.

Measure the resistance according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Switch Condition Specified Condition
G118-1 (CANH) - G118-2 (CANL) L - W Engine switch off 54 to 69 Ω
G118-1 (CANH) - G117-8 (PGND) L - W-B Engine switch off 200 Ω or higher
G118-2 (CANL) - G117-8 (PGND) W - W-B Engine switch off 200 Ω or higher
G118-1 (CANH) - G117-7 (+B) L - W Engine switch off 6 kΩ or higher
G118-2 (CANL) - G117-7 (+B) W - W Engine switch off 6 kΩ or higher



CHECK DRIVING SUPPORT ECU ASSEMBLY (w/ Pre-crash Safety System)


U170251E02
1.104,0.906 0.875,0.219 0.875,0.219 0.74,0.219 true 1.125,1.073 0.938,1.583 0.938,1.583 0.802,1.583 true 2.344,1.073 2.521,1.438 2.521,1.438 2.667,1.438 true 5.823,1.229 5.948,1.438 5.948,1.438 6.094,1.438 true 1.021,0.906 0.708,0.49 0.708,0.49 0.573,0.49 true 1.052,1.073 0.76,1.333 0.76,1.333 0.625,1.333 true 1.813,0.333 2.188,0.521 0.375,0.188 10 false G119 5.146,0.344 5.5,0.563 0.354,0.219 10 false G48 0.219,0.135 0.76,0.323 0.542,0.188 10 false CA2L*A 0.26,1.5 0.813,1.688 0.552,0.188 10 false CA2H*A 2.688,1.365 3.104,1.552 0.417,0.188 10 false GND 6.115,1.365 6.531,1.552 0.417,0.188 10 false BAT 0.042,0.406 0.594,0.594 0.552,0.188 10 false CA1N*B 0.094,1.26 0.635,1.448 0.542,0.188 10 false CA1P*B

Text in Illustration
*A for V2 Bus *B for Parking Assist Bus

NOTICE:
·

As disconnecting the connector to perform inspections may cause DTCs to be stored, clear DTCs after performing inspections.

·

As the connector may be damaged if a load of more than 10 kg (22 lb) is applied to it, do not apply any more load than necessary to the connector.



a.

Disconnect the driving support ECU assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

for V2 Bus
Terminal No. (Symbol) Wiring Color Switch Condition Specified Condition
G119-39 (CA2H) - G119-17 (CA2L) G - W Engine switch off 54 to 69 Ω
G119-39 (CA2H) - G119-25 (GND) G - BR Engine switch off 200 Ω or higher
G119-17 (CA2L) - G119-25 (GND) W - BR Engine switch off 200 Ω or higher
G119-39 (CA2H) - G48-16 (BAT) G - GR Engine switch off 6 kΩ or higher
G119-17 (CA2L) - G48-16 (BAT) W - GR Engine switch off 6 kΩ or higher

for Parking Assist Bus
Terminal No. (Symbol) Wiring Color Switch Condition Specified Condition
G119-40 (CA1P) - G119-18 (CA1N) L - W Engine switch off 108 to 132 Ω
G119-40 (CA1P) - G119-25 (GND) L - BR Engine switch off 200 Ω or higher
G119-18 (CA1N) - G119-25 (GND) W - BR Engine switch off 200 Ω or higher
G119-40 (CA1P) - G48-16 (BAT) L - GR Engine switch off 6 kΩ or higher
G119-18 (CA1N) - G48-16 (BAT) W - GR Engine switch off 6 kΩ or higher



CHECK PARKING ASSIST ECU (w/ Side Monitor System)


U148937E01
5.037,0.839 5.173,0.981 0.136,0.142 10 I6 3.307,0.839 3.443,0.981 0.136,0.142 10 I7 1.58,2.057 2.042,2.199 0.461,0.142 10 CANH 5.997,0.957 6.458,1.099 0.461,0.142 10 +B 3.815,0.93 4.276,1.072 0.461,0.142 10 GND1 2.005,2.269 2.467,2.411 0.461,0.142 10 CANL 2.419,2.34 2.536,2.34 2.536,2.34 2.671,1.659 false 2.008,2.125 2.124,2.125 2.124,2.125 2.575,1.659 false 5.97,1.018 5.853,1.018 5.853,1.018 5.564,1.506 false 4.659,1.506 4.373,0.988 4.373,0.988 4.247,0.988 false

a.

Disconnect the parking assist ECU connectors.


b.

Measure the resistance according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Switch Condition Specified Condition
I7-40 (CANH) - I7-39 (CANL) B - W Engine switch off 54 to 69 Ω
I7-40 (CANH) - I6-4 (GND1) B - W-B Engine switch off 200 Ω or higher
I7-39 (CANL) - I6-4 (GND1) W - W-B Engine switch off 200 Ω or higher
I7-40 (CANH) - I6-1 (+B) B - L Engine switch off 6 kΩ or higher
I7-39 (CANL) - I6-1 (+B) W - L Engine switch off 6 kΩ or higher



CHECK CLEARANCE WARNING ECU ASSEMBLY (w/ TOYOTA Parking Assist-sensor System)


a.

for 4 Sensor Type:

U148704E01
2.577,0.147 2.856,0.301 0.279,0.153 10 I1 3.74,0.266 3.950,0.420 0.210,0.153 10 R1 3.474,0.091 3.684,0.245 0.210,0.154 10 R2 3.491,0.731 3.641,0.335 3.641,0.335 3.712,0.335 false 3.14,0.731 3.374,0.152 3.374,0.152 3.446,0.152 false 1.98,1.402 2.114,1.556 0.133,0.154 10 E 2.605,1.016 2.169,1.471 2.169,1.471 2.098,1.471 false 5.615,0.139 5.909,0.352 0.295,0.212 10 G48 6.28,1.09 6.482,1.437 6.482,1.437 6.564,1.437 false 6.575,1.377 6.888,1.523 0.313,0.147 10 BAT

i.

Disconnect the clearance warning ECU assembly connector.


ii.

Measure the resistance according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Switch Condition Specified Condition
I1-3 (R1) - I1-5 (R2) R - W Engine switch off 54 to 69 Ω
I1-3 (R1) - I1-17 (E) R - W-B Engine switch off 200 Ω or higher
I1-5 (R2) - I1-17 (E) W - W-B Engine switch off 200 Ω or higher
I1-3 (R1) - G48-16 (BAT) R - GR Engine switch off 6 kΩ or higher
I1-5 (R2) - G48-16 (BAT) W - GR Engine switch off 6 kΩ or higher



b.

for 8 Sensor Type:

U148705E01
2.459,0.148 2.828,0.301 0.369,0.153 10 G154 3.74,0.266 3.950,0.420 0.210,0.153 10 R1 3.474,0.091 3.684,0.245 0.210,0.154 10 R2 3.491,0.731 3.641,0.335 3.641,0.335 3.712,0.335 false 3.14,0.731 3.374,0.152 3.374,0.152 3.446,0.152 false 1.98,1.402 2.114,1.556 0.133,0.154 10 E 2.605,1.016 2.169,1.471 2.169,1.471 2.098,1.471 false 5.615,0.139 5.909,0.352 0.295,0.212 10 G48 6.28,1.09 6.482,1.437 6.482,1.437 6.564,1.437 false 6.575,1.377 6.888,1.523 0.313,0.147 10 BAT

i.

Disconnect the clearance warning ECU assembly connector.


ii.

Measure the resistance according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Switch Condition Specified Condition
G154-3 (R1) - G154-5 (R2) L - W Engine switch off 54 to 69 Ω
G154-3 (R1) - G154-17 (E) L - W-B Engine switch off 200 Ω or higher
G154-5 (R2) - G154-17 (E) W - W-B Engine switch off 200 Ω or higher
G154-3 (R1) - G48-16 (BAT) L - GR Engine switch off 6 kΩ or higher
G154-5 (R2) - G48-16 (BAT) W - GR Engine switch off 6 kΩ or higher




CHECK HEADLIGHT SWIVEL ECU ASSEMBLY (for LED Headlight)


U148706E02
2.927,1.021 3.167,0.438 3.167,0.438 3.24,0.438 true 1.729,0.833 1.427,0.479 1.427,0.479 1.354,0.479 true 1.844,0.833 1.49,0.292 1.49,0.292 1.427,0.292 true 6.281,1.094 6.479,1.448 6.479,1.448 6.563,1.448 true 2.625,0.24 2.906,0.385 0.281,0.146 10 false A58 0.969,0.406 1.385,0.563 0.417,0.156 10 false CANL 1.01,0.219 1.49,0.375 0.479,0.156 10 false CANH 3.281,0.375 3.5,0.531 0.219,0.156 10 false E1 5.615,0.146 5.906,0.354 0.292,0.208 10 false G48 6.573,1.385 6.885,1.531 0.313,0.146 10 false BAT

a.

Disconnect the headlight swivel ECU assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Switch Condition Specified Condition
A58-12 (CANH) - A58-13 (CANL) V - W Engine switch off 54 to 69 Ω
A58-12 (CANH) - A58-22 (E1) V - W-B Engine switch off 200 Ω or higher
A58-13 (CANL) - A58-22 (E1) W - W-B Engine switch off 200 Ω or higher
A58-12 (CANH) - G48-16 (BAT) V - GR Engine switch off 6 kΩ or higher
A58-13 (CANL) - G48-16 (BAT) W - GR Engine switch off 6 kΩ or higher



CHECK MULTIPLEX TILT AND TELESCOPIC ECU (for Power Tilt and Power Telescopic Steering Column)


U148531E04
4.635,0.365 4.75,0.365 4.75,0.365 4.854,0.688 true 5.458,0.26 5.344,0.26 5.344,0.26 5.25,0.677 true 5.521,1.594 5.396,1.594 5.396,1.594 5.271,0.927 true 4.667,1.427 4.802,1.427 4.802,1.427 4.927,0.969 true 3.948,0.583 4.323,0.76 0.375,0.177 10 false G116 5.604,1.51 6.01,1.688 0.406,0.177 10 false CANP 5.521,0.177 5.927,0.354 0.406,0.177 10 false CANN 4.469,1.365 4.656,1.542 0.188,0.177 10 false +B 4.302,0.281 4.625,0.458 0.323,0.177 10 false GND

a.

Disconnect the multiplex tilt and telescopic ECU connector.


b.

Measure the resistance according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Switch Condition Specified Condition
G116-5 (CANP) - G116-14 (CANN) GR - W Engine switch off 54 to 69 Ω
G116-5 (CANP) - G116-11 (GND) GR - W-B Engine switch off 200 Ω or higher
G116-14 (CANN) - G116-11 (GND) W - W-B Engine switch off 200 Ω or higher
G116-5 (CANP) - G116-2 (+B) GR - G Engine switch off 6 kΩ or higher
G116-14 (CANN) - G116-2 (+B) W - G Engine switch off 6 kΩ or higher



CHECK FRONT POWER SEAT SWITCH RH (w/ Seat Position Memory)


U169655E02
4.948,1.531 4.833,1.531 4.833,1.531 4.365,1.229 true 2.177,1.26 2.281,1.26 2.281,1.26 3.51,0.938 true 4.969,0.844 4.833,0.844 4.833,0.844 4.448,1.177 true 2.24,1.49 2.375,1.49 2.375,1.49 3.531,1.125 true 4.979,1.458 5.385,1.635 0.406,0.177 10 false CANP 4.99,0.781 5.396,0.958 0.406,0.177 10 false CANN 2.01,1.417 2.198,1.594 0.188,0.177 10 false +B 1.854,1.188 2.177,1.365 0.323,0.177 10 false GND 4.167,0.302 4.344,0.458 0.177,0.156 10 false a5 3.167,0.302 3.344,0.458 0.177,0.156 10 false a4

a.

Disconnect the front power seat switch RH connectors.


b.

Measure the resistance according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Switch Condition Specified Condition
a5-8 (CANP) - a5-7 (CANN) L - W Engine switch off 54 to 69 Ω
a5-8 (CANP) - a4-2 (GND) L - W-B Engine switch off 200 Ω or higher
a5-7 (CANN) - a4-2 (GND) W - W-B Engine switch off 200 Ω or higher
a5-8 (CANP) - a4-7 (+B) L - W Engine switch off 6 kΩ or higher
a5-7 (CANN) - a4-7 (+B) W - W Engine switch off 6 kΩ or higher



CHECK DRIVING SUPPORT SWITCH CONTROL ECU (w/ Multi-function Switch)


a.

for Automatic Transmission:

U170367E02
4.427,1.49 5.052,0.938 5.052,0.938 5.292,0.938 true 5.031,0.729 4.854,0.729 4.854,0.729 4.292,1.5 true 3.792,1.5 3.448,0.875 3.448,0.875 3.292,0.875 true 4.542,1.667 5.073,2.302 5.073,2.302 5.198,2.302 true 4.031,0.667 4.396,0.813 0.365,0.146 10 false G163 5.333,0.844 6.063,1.01 0.729,0.167 10 false CANP 5.063,0.646 5.792,0.813 0.729,0.167 10 false CANN 5.25,2.219 5.979,2.385 0.729,0.167 10 false +B 2.938,0.781 3.667,0.948 0.729,0.167 10 false GND

i.

Disconnect the driving support switch control ECU connector.


ii.

Measure the resistance according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Switch Condition Specified Condition
G163-2 (CANP) - G163-3 (CANN) R - W Engine switch off 54 to 69 Ω
G163-2 (CANP) - G163-7 (GND) R - W-B Engine switch off 200 Ω or higher
G163-3 (CANN) - G163-7 (GND) W - W-B Engine switch off 200 Ω or higher
G163-2 (CANP) - G163-8 (+B) R - L Engine switch off 6 kΩ or higher
G163-3 (CANN) - G163-8 (+B) W - L Engine switch off 6 kΩ or higher



b.

for Manual Transmission:

U170606E01
3.516,0.313 3.797,0.452 0.282,0.139 10 G76 4.426,0.436 4.829,0.574 0.403,0.138 10 CANP 2.739,0.439 3.150,0.581 0.411,0.141 10 CANN 4.773,1.435 4.964,1.579 0.191,0.144 10 +B 2.091,1.442 2.417,1.582 0.326,0.141 10 GND 3.16,0.508 3.273,0.508 3.273,0.508 3.746,1.104 false 4.741,1.497 4.629,1.497 4.629,1.497 4.356,1.163 false 4.396,0.495 4.276,0.495 4.276,0.495 3.91,1.092 false 2.437,1.508 2.569,1.508 2.569,1.508 2.84,1.188 false

i.

Disconnect the driving support switch control ECU connector.


ii.

Measure the resistance according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Switch Condition Specified Condition
G76-9 (CANP) - G76-10 (CANN) R - W Engine switch off 54 to 69 Ω
G76-9 (CANP) - G76-16 (GND) R - W-B Engine switch off 200 Ω or higher
G76-10 (CANN) - G76-16 (GND) W - W-B Engine switch off 200 Ω or higher
G76-9 (CANP) - G76-6 (+B) R - L Engine switch off 6 kΩ or higher
G76-10 (CANN) - G76-6 (+B) W - L Engine switch off 6 kΩ or higher




CHECK BLIND SPOT MONITOR SENSOR LH (w/ Blind Spot Monitor Sensor)


U170328E01
2.141,0.408 2.414,0.547 0.273,0.139 10 R42 2.94,0.679 3.475,0.819 0.535,0.139 10 CA1P*A 3.045,0.887 3.580,1.026 0.535,0.139 10 CA2P*B 2.94,1.952 3.475,2.091 0.535,0.139 10 CA1N*A 3.045,1.747 3.580,1.887 0.535,0.139 10 CA2N*B 5.618,1.697 5.793,1.968 5.793,1.968 5.985,1.968 false 4.932,0.576 5.217,0.716 0.285,0.139 10 G48 6.015,1.898 6.550,2.037 0.535,0.139 10 BAT 2.66,1.216 2.835,0.945 2.835,0.945 3.026,0.945 false 1.061,1.747 1.507,1.887 0.446,0.139 10 BLGD 1.87,1.543 1.695,1.814 1.695,1.814 1.504,1.814 false 2.66,1.543 2.835,1.814 2.835,1.814 3.026,1.814 false 2.481,1.216 2.731,0.74 2.731,0.74 2.922,0.74 false 2.481,1.543 2.731,2.019 2.731,2.019 2.922,2.019 false

Text in Illustration
*A for V2 Bus *B for Sensor Bus

a.

Disconnect the blind spot monitor sensor LH connector.


b.

Measure the resistance according to the value(s) in the table below.

for V2 Bus
Terminal No. (Symbol) Wiring Color Switch Condition Specified Condition
R42-2 (CA1P) - R42-7 (CA1N) G - W Engine switch off 54 to 69 Ω
R42-2 (CA1P) - R42-10 (BLGD) G - W-B Engine switch off 200 Ω or higher
R42-7 (CA1N) - R42-10 (BLGD) W - W-B Engine switch off 200 Ω or higher
R42-2 (CA1P) - G48-16 (BAT) G - GR Engine switch off 6 kΩ or higher
R42-7 (CA1N) - G48-16 (BAT) W - GR Engine switch off 6 kΩ or higher

for Sensor Bus
Terminal No. (Symbol) Wiring Color Switch Condition Specified Condition
R42-1 (CA2P) - R42-6 (CA2N) V - W Engine switch off 108 to 132 Ω
R42-1 (CA2P) - R42-10 (BLGD) V - W-B Engine switch off 200 Ω or higher
R42-6 (CA2N) - R42-10 (BLGD) W - W-B Engine switch off 200 Ω or higher
R42-1 (CA2P) - G48-16 (BAT) V - GR Engine switch off 6 kΩ or higher
R42-6 (CA2N) - G48-16 (BAT) W - GR Engine switch off 6 kΩ or higher



CHECK BLIND SPOT MONITOR SENSOR RH (w/ Blind Spot Monitor Sensor)


U170329E01
2.144,0.408 2.428,0.547 0.284,0.139 10 R43 3.045,0.887 3.580,1.026 0.535,0.139 10 CA2P 3.045,1.747 3.580,1.887 0.535,0.139 10 CA2N 5.618,1.697 5.793,1.968 5.793,1.968 5.985,1.968 false 4.932,0.576 5.216,0.716 0.284,0.139 10 G48 6.015,1.898 6.550,2.037 0.535,0.139 10 BAT 2.66,1.216 2.835,0.945 2.835,0.945 3.026,0.945 false 1.073,1.747 1.507,1.887 0.434,0.139 10 BRGD 1.87,1.543 1.695,1.814 1.695,1.814 1.504,1.814 false 2.66,1.543 2.835,1.814 2.835,1.814 3.026,1.814 false

a.

Disconnect the blind spot monitor sensor RH connector.


b.

Measure the resistance according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Switch Condition Specified Condition
R43-1 (CA2P) - R43-6 (CA2N) V - W Engine switch off 108 to 132 Ω
R43-1 (CA2P) - R43-10 (BRGD) V - W-B Engine switch off 200 Ω or higher
R43-6 (CA2N) - R43-10 (BRGD) W - W-B Engine switch off 200 Ω or higher
R43-1 (CA2P) - G48-16 (BAT) V - GR Engine switch off 6 kΩ or higher
R43-6 (CA2N) - G48-16 (BAT) W - GR Engine switch off 6 kΩ or higher



CHECK TRANSMISSION CONTROL ECU ASSEMBLY (for 1KD-FTV and Automatic Transmission System)


U170042E02
5.229,1.26 4.927,0.604 4.927,0.604 4.792,0.604 true 2.469,1.26 2.771,0.604 2.771,0.604 2.917,0.604 true 6.125,1.854 6.302,2.198 6.302,2.198 6.49,2.198 true 6.281,2.427 6.104,2.427 6.104,2.427 5.948,1.844 true 5.5,0.313 5.854,0.49 0.354,0.177 10 false G70 1.563,0.323 1.875,0.5 0.313,0.177 10 false G69 2.948,0.542 3.229,0.677 0.281,0.135 10 false E1 6.333,2.354 6.802,2.542 0.469,0.188 10 false CAN+ 6.552,2.125 7.021,2.313 0.469,0.188 10 false CAN- 4.385,0.531 4.833,0.667 0.448,0.135 10 false BATT

a.

Disconnect the transmission control ECU assembly connectors.


b.

Measure the resistance according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Switch Condition Specified Condition
G70-21 (CAN+) - G70-20 (CAN-) B - W Engine switch off 108 to 132 Ω
G70-21 (CAN+) - G69-1 (E1) B - BR Engine switch off 200 Ω or higher
G70-20 (CAN-) - G69-1 (E1) W - BR Engine switch off 200 Ω or higher
G70-21 (CAN+) - G70-5 (BATT) B - L Engine switch off 6 kΩ or higher
G70-20 (CAN-) - G70-5 (BATT) W - L Engine switch off 6 kΩ or higher



CHECK MILLIMETER WAVE RADAR SENSOR ASSEMBLY (w/ Pre-crash Safety System)


U169954E01
1.702,0.233 1.990,0.401 0.288,0.167 10 A15 1.092,1.557 1.479,1.724 0.387,0.167 10 CA1P 2.066,1.553 2.473,1.720 0.408,0.167 10 CA1N 2.523,1.422 2.970,1.590 0.447,0.167 10 SGND 1.658,1.147 1.555,1.626 1.555,1.626 1.473,1.626 false 1.877,1.147 1.947,1.626 1.947,1.626 2.041,1.626 false 2.119,1.17 2.426,1.503 2.426,1.503 2.501,1.503 false 5.3,0.318 5.592,0.456 0.292,0.138 10 G48 6.214,1.425 6.519,1.600 0.305,0.174 10 BAT 5.96,1.256 6.098,1.502 6.098,1.502 6.202,1.502 false

a.

Disconnect the millimeter wave radar sensor assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Switch Condition Specified Condition
A15-4 (CA1P) - A15-3 (CA1N) L - W Engine switch off 108 to 132 Ω
A15-4 (CA1P) - A15-2 (SGND) L - BR Engine switch off 200 Ω or higher
A15-3 (CA1N) - A15-2 (SGND) W - BR Engine switch off 200 Ω or higher
A15-4 (CA1P) - G48-16 (BAT) L - GR Engine switch off 6 kΩ or higher
A15-3 (CA1N) - G48-16 (BAT) W - GR Engine switch off 6 kΩ or higher



CHECK REAR TELEVISION CAMERA ASSEMBLY (w/ Parking Assist Monitor System [for Camera built-in ECU])


U170477E02
2.531,0.49 2.458,0.49 2.458,0.49 2.146,0.906 true 2.177,1.177 2.458,1.594 2.458,1.594 2.542,1.594 true 5.938,1.25 6.052,1.552 6.052,1.552 6.146,1.552 true 5.302,0.813 5.031,0.458 5.031,0.458 4.938,0.458 true 2.563,0.406 3.958,0.583 1.396,0.177 10 false CANL*A, L*B 2.583,1.51 3.969,1.688 1.385,0.177 10 false CANH*A, H*B 6.198,1.479 6.552,1.646 0.354,0.167 10 false BAT 5.333,0.26 5.646,0.438 0.313,0.177 10 false G48 0.542,0.75 0.854,0.99 0.313,0.24 10 false v3 0.885,0.74 1.198,0.917 0.313,0.177 10 false *A 0.885,1.177 1.198,1.354 0.313,0.177 10 false *B 0.469,1.167 0.781,1.344 0.313,0.177 10 false X10 4.688,0.375 5.042,0.542 0.354,0.167 10 false CG

Text in Illustration
*A w/ Tire Carrier *B w/o Tire Carrier

a.

Disconnect the rear television camera assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

w/ Tire Carrier
Terminal No. (Symbol) Wiring Color Switch Condition Specified Condition
v3-4 (CANH) - v3-1 (CANL) B - W Engine switch off 54 to 69 Ω
v3-4 (CANH) - G48-4 (CG) B - W-B Engine switch off 200 Ω or higher
v3-1 (CANL) - G48-4 (CG) W - W-B Engine switch off 200 Ω or higher
v3-4 (CANH) - G48-16 (BAT) B - GR Engine switch off 6 kΩ or higher
v3-1 (CANL) - G48-16 (BAT) W - GR Engine switch off 6 kΩ or higher

w/o Tire Carrier
Terminal No. (Symbol) Wiring Color Switch Condition Specified Condition
X10-4 (H) - X10-1 (L) B - W Engine switch off 54 to 69 Ω
X10-4 (H) - G48-4 (CG) B - W-B Engine switch off 200 Ω or higher
X10-1 (L) - G48-4 (CG) W - W-B Engine switch off 200 Ω or higher
X10-4 (H) - G48-16 (BAT) B - GR Engine switch off 6 kΩ or higher
X10-1 (L) - G48-16 (BAT) W - GR Engine switch off 6 kΩ or higher



CHECK UREA PUMP CONTROL ECU (w/ Urea SCR System)


U170479E01
2.34,2.377 2.409,2.377 2.409,2.377 2.825,1.243 false 3.72,2.51 3.649,2.51 3.649,2.51 3.131,1.246 false 3.398,0.192 3.711,0.370 0.313,0.178 10 s4 3.232,1.246 3.97,2.237 3.97,2.237 4.041,2.237 false 4.06,2.165 4.659,2.343 0.599,0.178 10 CAN- 1.948,2.301 2.511,2.479 0.564,0.178 10 BATT 4.471,0.427 4.789,0.605 0.318,0.178 10 E01 3.751,2.439 4.313,2.617 0.561,0.177 10 CAN+ 3.718,1.574 4.361,0.502 4.361,0.502 4.432,0.502 false

a.

Disconnect the urea pump control ECU connector.


b.

Measure the resistance according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Switch Condition Specified Condition
s4-27 (CAN+) - s4-26 (CAN-) G - W Engine switch off 108 to 132 Ω
s4-27 (CAN+) - s4-52 (E01) G - W-B Engine switch off 200 Ω or higher
s4-26 (CAN-) - s4-52 (E01) W - W-B Engine switch off 200 Ω or higher
s4-27 (CAN+) - s4-30 (BATT) G - B Engine switch off 6 kΩ or higher
s4-26 (CAN-) - s4-30 (BATT) W - B Engine switch off 6 kΩ or higher



CHECK NITROGEN OXIDES SENSOR (w/ Urea SCR System)


U170478E02
5.958,1.26 6.198,1.469 6.198,1.469 6.292,1.469 true 1.99,0.896 2.563,0.5 2.563,0.5 2.635,0.5 true 1.854,0.885 1.333,0.375 1.333,0.375 1.229,0.375 true 1.76,0.906 1.115,0.74 1.115,0.74 1.01,0.74 true 1.844,0.229 2.156,0.406 0.313,0.177 10 false s6 5.281,0.229 5.594,0.406 0.313,0.177 10 false G48 0.854,0.292 1.458,0.469 0.604,0.177 10 false CAN- 0.656,0.646 1.052,0.823 0.396,0.177 10 false GND 2.698,0.427 3.26,0.604 0.563,0.177 10 false CAN+ 6.344,1.406 6.708,1.573 0.365,0.167 10 false BAT

a.

Disconnect the nitrogen oxides sensor connector.


b.

Measure the resistance according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Switch Condition Specified Condition
s6-4 (CAN+) - s6-3 (CAN-) L - W Engine switch off 54 to 69 Ω
s6-4 (CAN+) - s6-2 (GND) L - W-B Engine switch off 200 Ω or higher
s6-3 (CAN-) - s6-2 (GND) W - W-B Engine switch off 200 Ω or higher
s6-4 (CAN+) - G48-16 (BAT) L - GR Engine switch off 6 kΩ or higher
s6-3 (CAN-) - G48-16 (BAT) W - GR Engine switch off 6 kΩ or higher