Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM(for RHD with Entry and Start System) › 2015.06–2017.08
RM27T0E _57 Power Source / Network _053729 NETWORKING _0261033 CAN COMMUNICATION SYSTEM(for RHD with Entry and Start System) C

NETWORKING  CAN COMMUNICATION SYSTEM(for RHD with Entry and Start System)  U0132  Lost Communication with Ride Level Control Module  


DESCRIPTION

DTC Code DTC Detection Condition Trouble Area
U0132 There is no communication from the suspension control ECU.
·

Power source or inside suspension control ECU

·

Suspension control ECU CAN branch wire or connector

·

Suspension control ECU



For vehicles with an air suspension system.


WIRING DIAGRAM

C217350E60
5.385,2.719 5.781,2.896 0.396,0.177 10 false A49 5.385,2.917 6.948,3.281 1.563,0.365 10 false Suspension Control ECU 0.625,1.427 1.021,1.604 0.396,0.177 10 false G98 0.625,1.604 2.281,1.781 1.656,0.177 10 false No. 3 Junction Connector 5.823,0.573 6.292,0.75 0.469,0.177 10 false CANH 1.948,0.5 2.052,0.656 0.104,0.156 10 false 3 5.635,0.448 5.813,0.604 0.177,0.156 10 false 7 5.635,0.885 5.813,1.042 0.177,0.156 10 false 8 5.635,1.792 5.823,1.948 0.188,0.156 10 false 3 5.646,2.167 5.76,2.323 0.115,0.156 10 false 5 4.365,1.771 5.406,1.927 1.042,0.156 10 false AIR SUS NO. 2 2.406,1.938 3.698,2.115 1.292,0.177 10 false from AIR SUS Fuse 1.948,0.906 2.146,1.063 0.198,0.156 10 false 14 5.823,1.01 6.292,1.188 0.469,0.177 10 false CANL 5.823,1.917 5.958,2.094 0.135,0.177 10 false B 5.823,2.323 6.292,2.5 0.469,0.177 10 false GND

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


HINT:

Operating the engine switch, any switches or any doors triggers related ECU and sensor communication with the CAN, which causes resistance variation.


PROCEDURE

1.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL
a.

Disconnect the cable from the negative (-) battery terminal before measuring the resistances of the CAB main wire and the CAN branch wire.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the airbag system.


NOTICE:
·

After turning the engine switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).

·

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).





NEXT

2.CHECK FOR OPEN IN CAN BUS WIRE (SUSPENSION CONTROL ECU CAN BRANCH WIRE)
2.CHECK FOR OPEN IN CAN BUS WIRE (SUSPENSION CONTROL ECU CAN BRANCH WIRE)
a.
U148529E03
2.385,1.385 2.552,0.906 2.552,0.906 2.635,0.906 true 2.781,1.156 2.698,1.156 2.698,1.156 2.479,1.396 true 0.052,0 0.24,0.229 0.188,0.229 10 false *a 2.667,0.833 3.115,1 0.448,0.167 10 false CANL 2.823,1.073 3.271,1.24 0.448,0.167 10 false CANH 0.896,1.198 1.198,1.365 0.302,0.167 10 false A49

Disconnect the A49 suspension control ECU connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
A49-7 (CANH) - A49-8 (CANL) Engine switch off 54 to 69 Ω


Text in Illustration
*a Rear view of wire harness connector
(to Suspension Control ECU)



OK

3.CHECK HARNESS AND CONNECTOR (SUSPENSION CONTROL ECU - BATTERY AND BODY GROUND)

NG

REPAIR OR REPLACE SUSPENSION CONTROL ECU CAN BRANCH WIRE OR CONNECTOR (CANH, CANL)

3.CHECK HARNESS AND CONNECTOR (SUSPENSION CONTROL ECU - BATTERY AND BODY GROUND)
a.
U170099E02
2.167,1.229 2.604,0.875 2.604,0.875 2.688,0.875 true 1.417,1.885 1.5,1.885 1.5,1.885 1.896,1.302 true 0.052,0 0.24,0.229 0.188,0.229 10 false *a 2.729,0.792 2.865,0.958 0.135,0.167 10 false B 1.021,1.792 1.375,1.958 0.354,0.167 10 false GND 0.865,1.177 1.198,1.344 0.333,0.167 10 false A49

Connect the cable to the negative (-) battery terminal.

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).



b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A49-5 (GND) - Body ground Always Below 1 Ω



c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A49-3 (B) - Body ground Always 11 to 14 V



Text in Illustration
*a Rear view of wire harness connector
(to Suspension Control ECU)


OK

REPLACE SUSPENSION CONTROL ECU

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR