Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM(for RHD with Entry and Start System) › 2015.06–2017.08
RM27T0E _57 Power Source / Network _053729 NETWORKING _0261033 CAN COMMUNICATION SYSTEM(for RHD with Entry and Start System) C

NETWORKING  CAN COMMUNICATION SYSTEM(for RHD with Entry and Start System)  U0104  Lost Communication with Driving Support ECU  


DESCRIPTION

DTC Code DTC Detection Condition Trouble Area
U0104 There is no communication from the driving support ECU assembly.
·

Power source or inside driving support ECU assembly

·

Driving support ECU assembly CAN branch wire or connector

·

Driving support ECU assembly



For vehicles with a pre-crash safety system.


WIRING DIAGRAM

C217350E24
5.569,2.665 5.964,2.841 0.395,0.176 10 G119 5.569,2.824 6.927,3.188 1.358,0.364 10 Driving Support ECU Assembly 0.628,1.381 1.028,1.557 0.400,0.176 10 G98 0.628,1.54 2.283,1.717 1.655,0.176 10 No. 3 Junction Connector 5.821,0.528 6.287,0.704 0.466,0.176 10 CA2H 1.95,0.43 2.058,0.584 0.109,0.154 10 4 5.555,0.446 5.736,0.600 0.181,0.154 10 39 5.555,0.886 5.736,1.040 0.181,0.154 10 17 5.553,1.803 5.745,1.956 0.192,0.154 10 30 5.544,2.175 5.747,2.328 0.203,0.154 10 25 4.362,1.766 5.305,1.920 0.943,0.154 10 ECU-IG NO. 1 2.338,1.884 3.696,2.056 1.358,0.172 10 from IG1 NO.1 Relay 1.95,0.884 2.144,1.037 0.194,0.153 10 15 5.821,0.966 6.287,1.142 0.466,0.176 10 CA2L 5.821,1.889 6.287,2.066 0.466,0.176 10 B 5.821,2.278 6.287,2.454 0.466,0.176 10 GND

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


HINT:

Operating the engine switch, any switches or any doors triggers related ECU and sensor communication with the CAN, which causes resistance variation.


PROCEDURE

1.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL
a.

Disconnect the cable from the negative (-) battery terminal before measuring the resistances of the CAB main wire and the CAN branch wire.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the airbag system.


NOTICE:
·

After turning the engine switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).

·

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).





NEXT

2.CHECK FOR OPEN IN CAN BUS WIRE (DRIVING SUPPORT ECU ASSEMBLY CAN BRANCH WIRE)
2.CHECK FOR OPEN IN CAN BUS WIRE (DRIVING SUPPORT ECU ASSEMBLY CAN BRANCH WIRE)
a.
U170203E02
0.875,1.51 1.031,1.51 1.031,1.51 1.208,1.896 true 0.938,2.594 1.125,2.594 1.125,2.594 1.229,2.042 true 0.542,2.51 0.927,2.688 0.385,0.177 10 false CA2H 0.49,1.427 0.854,1.604 0.365,0.177 10 false CA2L 1.729,0.333 2.104,0.51 0.375,0.177 10 false G119 0.063,0.01 0.271,0.188 0.208,0.177 10 false *a

Disconnect the G119 driving support ECU assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
G119-39 (CA2H) - G119-17 (CA2L) Engine switch off 54 to 69 Ω


Text in Illustration
*a Rear view of wire harness connector
(to Driving Support ECU Assembly)



OK

3.CHECK HARNESS AND CONNECTOR (DRIVING SUPPORT ECU ASSEMBLY - BATTERY AND BODY GROUND)

NG

REPAIR OR REPLACE DRIVING SUPPORT ECU ASSEMBLY CAN BRANCH WIRE OR CONNECTOR (CA2H, CA2L)

3.CHECK HARNESS AND CONNECTOR (DRIVING SUPPORT ECU ASSEMBLY - BATTERY AND BODY GROUND)
a.
U170204E01
2.602,2.512 2.958,2.662 0.356,0.150 10 GND 1.294,2.414 1.406,2.595 0.112,0.181 10 B 1.434,2.49 1.595,2.49 1.595,2.49 1.924,2.008 false 2.574,2.6 2.387,2.6 2.387,2.6 2.278,2.046 false 0.381,1.891 0.758,2.069 0.377,0.178 10 G119 0.062,0.051 0.275,0.229 0.213,0.178 10 *a

Connect the cable to the negative (-) battery terminal.

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).



b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G119-25 (GND) - Body ground Always Below 1 Ω



c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
G119-30 (B) - Body ground Always 11 to 14 V



Text in Illustration
*a Rear view of wire harness connector
(to Driving Support ECU Assembly)


OK

REPLACE DRIVING SUPPORT ECU ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR