Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM(for RHD with Entry and Start System) › 2015.06–2017.08
RM27T0E _57 Power Source / Network _053729 NETWORKING _0261033 CAN COMMUNICATION SYSTEM(for RHD with Entry and Start System) C

NETWORKING  CAN COMMUNICATION SYSTEM(for RHD with Entry and Start System)  U0208  Lost Communication with "Seat Control Module A"  


DESCRIPTION

DTC Code DTC Detection Condition Trouble Area
U0208 There is no communication from the front power seat switch RH.
·

Power source or inside front power seat switch RH

·

Front power seat switch RH CAN branch wire or connector

·

Front power seat switch RH



For vehicles with a seat position memory.


WIRING DIAGRAM

E346817E01
0.323,1.854 0.938,2.052 0.615,0.198 10 false G133 0.333,2.031 1.958,2.24 1.625,0.208 10 false No. 2 Junction Connector 1.938,0.938 2.552,1.135 0.615,0.198 10 false 2 1.938,1.344 2.552,1.542 0.615,0.198 10 false 13 4.938,1.031 5.552,1.229 0.615,0.198 10 false a5 4.969,0.865 5.583,1.063 0.615,0.198 10 false 8 5.26,1.042 5.875,1.24 0.615,0.198 10 false CANP 5.26,1.5 5.875,1.698 0.615,0.198 10 false CANN 4.927,1.479 5.542,1.677 0.615,0.198 10 false a5 4.99,1.302 5.604,1.5 0.615,0.198 10 false 7 4.938,2.24 5.552,2.438 0.615,0.198 10 false a4 5,2.052 5.615,2.25 0.615,0.198 10 false 7 4.927,2.708 5.542,2.906 0.615,0.198 10 false a5 4.938,3.229 5.552,3.427 0.615,0.198 10 false a4 4.938,2.5 5.552,2.698 0.615,0.198 10 false 12 4.99,3.031 5.604,3.229 0.615,0.198 10 false 2 5.25,2.25 5.865,2.448 0.615,0.198 10 false +B 5.26,2.698 5.875,2.896 0.615,0.198 10 false SYSB 5.25,3.25 5.865,3.448 0.615,0.198 10 false GND 3.979,2.125 4.813,2.323 0.833,0.198 10 false P/SEAT FR 4.115,2.552 4.948,2.75 0.833,0.198 10 false ECU-B 2.542,2.688 3.375,2.885 0.833,0.198 10 false from Battery 2.542,2.229 3.375,2.427 0.833,0.198 10 false from Battery 5.125,3.885 6.198,4.24 1.073,0.354 10 false Front Power Seat Switch RH

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


HINT:

Operating the engine switch, any switches or any doors triggers related ECU and sensor communication with the CAN, which causes resistance variation.


PROCEDURE

1.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL
a.

Disconnect the cable from the negative (-) battery terminal before measuring the resistances of the CAB main wire and the CAN branch wire.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the airbag system.


NOTICE:
·

After turning the engine switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).

·

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).





NEXT

2.CHECK FOR OPEN IN CAN BUS WIRE (FRONT POWER SEAT SWITCH RH CAN BRANCH WIRE)
2.CHECK FOR OPEN IN CAN BUS WIRE (FRONT POWER SEAT SWITCH RH CAN BRANCH WIRE)
a.
U169961E01
0.078,0.055 0.251,0.223 0.173,0.168 10 *a 1.829,1.704 2.264,1.872 0.435,0.168 10 CANN 1.843,1.913 2.278,2.081 0.435,0.168 10 CANP 1.801,1.792 1.736,1.792 1.736,1.792 1.605,1.599 false 1.801,2.015 1.736,2.015 1.736,2.015 1.519,1.582 false 0.547,1.286 0.821,1.454 0.274,0.168 10 a5

Disconnect the a5 front power seat switch RH connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
a5-8 (CANP) - a5-7 (CANN) Engine switch off 54 to 69 Ω


Text in Illustration
*a Rear view of wire harness connector
(to Front Power Seat Switch RH)



OK

3.CHECK HARNESS AND CONNECTOR (FRONT POWER SEAT SWITCH RH - BATTERY AND BODY GROUND)

NG

REPAIR OR REPLACE FRONT POWER SEAT SWITCH RH CAN BRANCH WIRE OR CONNECTOR (CANP, CANN)

3.CHECK HARNESS AND CONNECTOR (FRONT POWER SEAT SWITCH RH - BATTERY AND BODY GROUND)
a.
U169962E02
2.729,1.813 2.656,1.813 2.656,1.813 2.458,1.406 true 0.708,2.01 0.771,2.01 0.771,2.01 0.99,1.573 true 2.719,0.802 2.656,0.802 2.656,0.802 2.458,1.208 true 0.198,0.104 0.375,0.271 0.177,0.167 10 false *a 2.771,1.708 2.99,1.875 0.219,0.167 10 false +B 0.25,1.906 0.688,2.073 0.438,0.167 10 false SYSB 2.99,1.146 3.26,1.313 0.271,0.167 10 false a4 0.344,1.333 0.615,1.5 0.271,0.167 10 false a5 2.771,0.729 3.125,0.896 0.354,0.167 10 false GND

Connect the cable to the negative (-) battery terminal.

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).



b.

Disconnect the a4 front power seat switch RH connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
a4-2 (GND) - Body ground Always Below 1 Ω



d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
a4-7 (+B) - Body ground Always 11 to 14 V
a5-12 (SYSB) - Body ground Always 11 to 14 V



Text in Illustration
*a Rear view of wire harness connector
(to Front Power Seat Switch RH)


OK

REPLACE FRONT POWER SEAT SWITCH RH

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR