Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM(for RHD with Entry and Start System) › 2015.06–2017.08
RM27T0E _57 Power Source / Network _053729 NETWORKING _0261033 CAN COMMUNICATION SYSTEM(for RHD with Entry and Start System) C

NETWORKING  CAN COMMUNICATION SYSTEM(for RHD with Entry and Start System)  U110B  Lost Communication with Parking Assist Control Module "B"  


DESCRIPTION

DTC Code DTC Detection Condition Trouble Area
U110B There is no communication from the parking assist ECU.
·

Power source or inside of parking assist ECU

·

Parking assist ECU CAN branch wire or connector

·

Parking assist ECU



For vehicles with a side monitor system.


WIRING DIAGRAM

C288334E06
5.302,0.573 5.49,0.771 0.188,0.198 10 false I7 0.469,1.552 0.927,1.75 0.458,0.198 10 false G95 0.49,1.708 2.135,1.906 1.646,0.198 10 false No. 2 Junction Connector 1.708,0.458 2.167,0.656 0.458,0.198 10 false 4 1.719,1.031 2.177,1.229 0.458,0.198 10 false 15 2.198,2.104 3.094,2.313 0.896,0.208 10 false from Battery 1.75,2.813 3.125,3.042 1.375,0.229 10 false from IG1 NO.1 Relay 1.99,3.552 3.125,3.771 1.135,0.219 10 false from ACC Relay 4.135,1.948 4.594,2.146 0.458,0.198 10 false ECU-B 3.99,2.667 4.917,2.865 0.927,0.198 10 false ECU-IG NO.2 4.188,3.406 4.646,3.604 0.458,0.198 10 false ACC 5.313,1.156 5.469,1.354 0.156,0.198 10 false I7 5.302,2.115 5.458,2.313 0.156,0.198 10 false I6 5.323,2.854 5.5,3.073 0.177,0.219 10 false I6 5.323,3.563 5.479,3.76 0.156,0.198 10 false I6 5.313,4.146 5.448,4.344 0.135,0.198 10 false I6 5.313,3.927 5.771,4.125 0.458,0.198 10 false 4 5.323,3.323 5.781,3.521 0.458,0.198 10 false 9 5.333,2.615 5.792,2.813 0.458,0.198 10 false 8 5.313,1.875 5.771,2.073 0.458,0.198 10 false 1 5.292,0.917 5.469,1.104 0.177,0.188 10 false 39 5.292,0.344 5.521,0.542 0.229,0.198 10 false 40 5.635,0.583 6.406,0.781 0.771,0.198 10 false CANH 5.635,1.167 6.406,1.365 0.771,0.198 10 false CANL 5.646,2.115 6.417,2.313 0.771,0.198 10 false +B 5.656,2.854 6.427,3.052 0.771,0.198 10 false IG 5.646,3.573 6.417,3.771 0.771,0.198 10 false ACC 5.646,4.156 6.417,4.354 0.771,0.198 10 false GND1 5.458,5.146 6.75,5.354 1.292,0.208 10 false Parking Assist ECU

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


HINT:

Operating the engine switch, any switches or any doors triggers related ECU and sensor communication with the CAN, which causes resistance variation.


PROCEDURE

1.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL
a.

Disconnect the cable from the negative (-) battery terminal before measuring the resistances of the CAN main wire and the CAN branch wire.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the airbag system.


NOTICE:
·

After turning the engine switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).

·

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).





NEXT

2.CHECK FOR OPEN IN CAN BUS WIRE (PARKING ASSIST ECU CAN BRANCH WIRE)
2.CHECK FOR OPEN IN CAN BUS WIRE (PARKING ASSIST ECU CAN BRANCH WIRE)
a.
U148914E01
1.718,0.24 1.854,0.376 0.136,0.136 10 I7 0.089,0.094 0.258,0.255 0.170,0.161 10 *a 0.667,1.528 1.064,1.667 0.397,0.139 10 CANL 0.364,1.27 0.785,1.409 0.420,0.139 10 CANH 1.08,1.151 0.992,1.342 0.992,1.342 0.869,1.342 false 1.14,1.151 1.275,1.603 1.275,1.603 1.152,1.603 false

Disconnect the I7 parking assist ECU connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
I7-40 (CANH) - I7-39 (CANL) Engine switch off 54 to 69 Ω


Text in Illustration
*a Rear view of wire harness connector
(to Parking Assist ECU)



OK

3.CHECK HARNESS AND CONNECTOR (PARKING ASSIST ECU - BATTERY AND BODY GROUND)

NG

REPAIR OR REPLACE PARKING ASSIST ECU CAN BRANCH WIRE OR CONNECTOR (CANH, CANL)

3.CHECK HARNESS AND CONNECTOR (PARKING ASSIST ECU - BATTERY AND BODY GROUND)
a.
U148915E02
1.99,1.271 2.188,1.573 2.188,1.573 2.323,1.573 true 1.271,1.125 1.125,0.958 1.125,0.958 0.958,0.958 true 2.271,1.125 2.427,0.958 2.427,0.958 2.573,0.958 true 1.917,1.26 2.01,1.844 2.01,1.844 2.125,1.844 true 0.094,0.094 0.26,0.25 0.167,0.156 10 false *a 2.375,1.5 2.781,1.698 0.406,0.198 10 false IG 2.604,0.885 2.823,1.073 0.219,0.188 10 false +B 0.552,0.875 0.958,1.052 0.406,0.177 10 false GND1 2.177,1.771 2.594,1.969 0.417,0.198 10 false ACC 1.708,0.26 1.844,0.396 0.135,0.135 10 false I6

Connect the cable to the negative (-) battery terminal.

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).



b.

Disconnect the I6 parking assist ECU connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
I6-4 (GND1) - Body ground Always Below 1 Ω



d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
I6-1 (+B) - Body ground Always 11 to 14 V
I6-8 (IG) - Body ground Engine switch on (IG) 11 to 14 V
I6-9 (ACC) - Body ground Engine switch on (ACC) 11 to 14 V



Text in Illustration
*a Rear view of wire harness connector
(to Parking Assist ECU)


OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR