Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM(for RHD with Entry and Start System) › 2015.06–2017.08
RM27T0E _57 Power Source / Network _053729 NETWORKING _0261033 CAN COMMUNICATION SYSTEM(for RHD with Entry and Start System) J

NETWORKING  CAN COMMUNICATION SYSTEM(for RHD with Entry and Start System)  Power Management Control ECU Communication Stop Mode  


DESCRIPTION

Detection Item Symptom Trouble Area
Power Management Control ECU Communication Stop Mode Either condition is met:
·

"Power Management1" is not displayed on "Bus Check".

·

"Power Management Control ECU Communication Stop Mode" in "DTC Combination Table" applies.


·

Power source or inside power management control ECU

·

Power management control ECU CAN branch wire or connector

·

Power management control ECU



WIRING DIAGRAM

C201306E36
0.49,1.302 0.885,1.479 0.396,0.177 10 false G134 3.104,1.354 3.927,1.531 0.823,0.177 10 false from Battery 4.438,1.208 4.771,1.385 0.333,0.177 10 false AM2 5.854,2.604 6.292,2.781 0.438,0.177 10 false GND 5.656,2.469 5.781,2.646 0.125,0.177 10 false 6 5.844,2.188 6.281,2.365 0.438,0.177 10 false GND2 5.656,2.063 5.781,2.24 0.125,0.177 10 false 5 5.865,1.354 6.302,1.531 0.438,0.177 10 false AM22 5.656,1.198 5.781,1.375 0.125,0.177 10 false 1 5.854,1.771 6.292,1.948 0.438,0.177 10 false AM21 5.646,1.667 5.771,1.844 0.125,0.177 10 false 2 5.854,0.417 6.292,0.594 0.438,0.177 10 false CA1H 5.583,0.292 5.781,0.469 0.198,0.177 10 false 14 5.844,0.833 6.281,1.01 0.438,0.177 10 false CA1L 5.604,0.708 5.802,0.885 0.198,0.177 10 false 13 1.74,0.292 1.938,0.469 0.198,0.177 10 false 4 1.729,0.719 1.927,0.896 0.198,0.177 10 false 15 0.49,1.458 2.115,1.635 1.625,0.177 10 false No. 3 Junction Connector 5,3 5.438,3.177 0.438,0.177 10 false G51 5.021,3.188 7.146,3.375 2.125,0.188 10 false Power Management Control ECU

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


HINT:

Operating the engine switch, any switches or any doors triggers related ECU and sensor communication with the CAN, which causes resistance variation.


PROCEDURE

1.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL
a.

Disconnect the cable from the negative (-) battery terminal before measuring the resistances of the CAN main wire and the CAN branch wire.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the airbag system.


NOTICE:
·

After turning the engine switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).

·

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).





NEXT

2.CHECK FOR OPEN IN CAN BUS WIRE (POWER MANAGEMENT CONTROL ECU CAN BRANCH WIRE)
2.CHECK FOR OPEN IN CAN BUS WIRE (POWER MANAGEMENT CONTROL ECU CAN BRANCH WIRE)
a.
U148241E03
1.813,1.302 1.667,1.969 1.667,1.969 1.531,1.969 true 1.74,1.323 1.344,1.76 1.344,1.76 1.25,1.76 true 0.031,0.031 0.271,0.219 0.24,0.188 10 true *a 1.083,1.885 1.458,2.042 0.375,0.156 10 false CA1L 0.74,1.667 1.167,1.823 0.427,0.156 10 false CA1H 0.552,1.188 0.885,1.344 0.333,0.156 10 false G51

Disconnect the G51 power management control ECU connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
G51-14 (CA1H) - G51-13 (CA1L) Engine switch off 54 to 69 Ω


Text in Illustration
*a Rear view of wire harness connector
(to Power Management Control ECU)



OK

3.CHECK HARNESS AND CONNECTOR (POWER MANAGEMENT CONTROL ECU - BATTERY AND BODY GROUND)

NG

REPAIR OR REPLACE POWER MANAGEMENT CONTROL ECU CAN BRANCH WIRE OR CONNECTOR (CA1H, CA1L)

3.CHECK HARNESS AND CONNECTOR (POWER MANAGEMENT CONTROL ECU - BATTERY AND BODY GROUND)
a.
U148240E03
2.604,0.604 2.531,0.604 2.531,0.604 2.354,1.146 true 2.448,1.156 2.667,0.844 2.667,0.844 2.76,0.844 true 1.042,1.677 1.115,1.677 1.115,1.677 1.448,1.188 true 1.354,1.188 0.979,1.438 0.979,1.438 0.885,1.438 true 0.042,0.021 0.281,0.208 0.24,0.188 10 true *a 2.771,0.771 3.198,0.927 0.427,0.156 10 false AM22 0.479,1.354 0.823,1.51 0.344,0.156 10 false GND 0.51,1.604 0.938,1.76 0.427,0.156 10 false GND2 2.615,0.521 3.021,0.677 0.406,0.156 10 false AM21 2.813,1.271 3.146,1.427 0.333,0.156 10 false G51

Connect the cable to the negative (-) battery terminal.

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).



b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G51-5 (GND2) - Body ground Always Below 1 Ω
G51-6 (GND) - Body ground Always Below 1 Ω



c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
G51-1 (AM22) - Body ground Always 11 to 14 V
G51-2 (AM21) - Body ground Always 11 to 14 V



Text in Illustration
*a Rear view of wire harness connector
(to Power Management Control ECU)


OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR