Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM(for RHD with Entry and Start System) › 2015.06–2017.08
RM27T0E _57 Power Source / Network _053729 NETWORKING _0261033 CAN COMMUNICATION SYSTEM(for RHD with Entry and Start System) C

NETWORKING  CAN COMMUNICATION SYSTEM(for RHD with Entry and Start System)  U0164  Lost Communication with A/C ECU  


DESCRIPTION

DTC Code DTC Detection Condition Trouble Area
U0164 There is no communication from the air conditioning amplifier assembly.
·

Power source or inside air conditioning amplifier assembly

·

Air conditioning amplifier assembly CAN branch wire or connector

·

Air conditioning amplifier assembly



WIRING DIAGRAM

C198937E57
5.386,2.779 5.814,2.955 0.428,0.176 10 G25 5.386,2.938 7.011,3.302 1.626,0.364 10 Air Conditioning Amplifier Assembly 0.619,1.425 1.019,1.601 0.400,0.176 10 G98 0.619,1.584 2.347,1.761 1.729,0.176 10 No. 3 Junction Connector 5.812,0.572 6.278,0.748 0.466,0.176 10 CANH 1.936,0.474 2.932,0.628 0.995,0.154 10 10*1, 6*2 5.532,0.474 5.732,0.628 0.200,0.154 10 11 5.532,0.928 5.732,1.081 0.200,0.154 10 12 5.532,1.37 5.732,1.524 0.200,0.154 10 21 4.961,1.336 5.237,1.490 0.275,0.154 10 A/C 3.362,1.454 4.164,1.626 0.802,0.172 10 from Battery 2.796,1.897 4.159,2.069 1.363,0.172 10 from IG1 NO. 1 Relay 4.6,1.763 5.513,1.917 0.913,0.154 10 ECU-IG NO. 2 5.594,1.813 5.713,1.966 0.119,0.154 10 1 5.532,2.255 5.732,2.409 0.200,0.154 10 14 1.941,0.928 3.088,1.081 1.148,0.153 10 21*1, 17*2 5.812,1.01 6.278,1.186 0.466,0.176 10 CANL 5.812,1.46 6.278,1.636 0.466,0.176 10 B 5.812,1.91 6.278,2.087 0.466,0.176 10 IG+ 5.812,2.353 6.278,2.529 0.466,0.176 10 GND 0.115,2.917 2.151,3.070 2.037,0.153 10 *1: for 1KD-FTV 0.115,3.281 2.151,3.435 2.037,0.153 10 *2: for 1GR-FE, 1GD-FTV

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


HINT:

Operating the engine switch, any switches or any doors triggers related ECU and sensor communication with the CAN, which causes resistance variation.


PROCEDURE

1.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL
a.

Disconnect the cable from the negative (-) battery terminal before measuring the resistances of the main wire and branch wire.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.


NOTICE:
·

After turning the engine switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).

·

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).





NEXT

2.CHECK FOR OPEN IN CAN BUS WIRE (AIR CONDITIONING AMPLIFIER ASSEMBLY CAN BRANCH WIRE)
2.CHECK FOR OPEN IN CAN BUS WIRE (AIR CONDITIONING AMPLIFIER ASSEMBLY CAN BRANCH WIRE)
a.
U170011E02
2.125,1.073 2.167,0.167 2.167,0.167 2.333,0.167 true 2.01,1.073 1.615,0.313 1.615,0.313 1.49,0.313 true 0.052,0 0.229,0.208 0.177,0.208 10 false *a 2.385,0.104 2.823,0.271 0.438,0.167 10 false CANH 1.115,0.229 1.521,0.406 0.406,0.177 10 false CANL 0.385,0.979 0.667,1.156 0.281,0.177 10 false G25

Disconnect the air conditioning amplifier assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
G25-11 (CANH) - G25-12 (CANL) Engine switch off 54 to 64 Ω


Text in Illustration
*a Rear view of wire harness connector
(to Air Conditioning Amplifier Assembly)



OK

3.CHECK HARNESS AND CONNECTOR (AIR CONDITIONING AMPLIFIER ASSEMBLY - BATTERY AND BODY GROUND)

NG

REPAIR OR REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY CAN BRANCH WIRE OR CONNECTOR (CANH, CANL)

3.CHECK HARNESS AND CONNECTOR (AIR CONDITIONING AMPLIFIER ASSEMBLY - BATTERY AND BODY GROUND)
a.
U170010E02
3.198,1.25 3.01,1.854 3.01,1.854 2.885,1.854 true 3.177,1.052 2.906,0.177 2.906,0.177 2.781,0.177 true 1.781,1.063 1.385,0.385 1.385,0.385 1.25,0.385 true 0.052,0 0.229,0.208 0.177,0.208 10 false *a 2.531,0.104 2.813,0.271 0.281,0.167 10 false IG+ 2.74,1.771 2.885,1.948 0.146,0.177 10 false B 0.927,0.313 1.281,0.479 0.354,0.167 10 false GND 0.354,0.865 0.646,1.042 0.292,0.177 10 false G25

Connect the cable to the negative (-) battery terminal.

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).



b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G25-14 (GND) - Body ground Always Below 1 Ω



c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
G25-21 (B) - Body ground Always 11 to 14 V
G25-1 (IG+) - Body ground Engine switch on (IG) 11 to 14 V



Text in Illustration
*a Rear view of wire harness connector
(to Air Conditioning Amplifier Assembly)


OK

REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR