Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM(for RHD with Entry and Start System) › 2015.06–2017.08
RM27T0E _57 Power Source / Network _053729 NETWORKING _0261033 CAN COMMUNICATION SYSTEM(for RHD with Entry and Start System) C

NETWORKING  CAN COMMUNICATION SYSTEM(for RHD with Entry and Start System)  U029D/A2  Lost Communication with NOx Sensor "A"  


DESCRIPTION

DTC Code DTC Detection Condition Trouble Area
U029D/A2 There is no communication from the nitrogen oxides sensor.
·

Power source or inside nitrogen oxides sensor

·

Nitrogen oxides sensor CAN branch wire or connector

·

Nitrogen oxides sensor



For vehicles with a urea SCR system.


WIRING DIAGRAM

C329299E03
5.313,1.073 5.927,1.271 0.615,0.198 10 false CAN+ 5.323,1.521 5.938,1.719 0.615,0.198 10 false CAN- 5.302,2.458 5.917,2.656 0.615,0.198 10 false BATT 5.313,3.271 5.927,3.469 0.615,0.198 10 false GND 5.031,0.938 5.188,1.135 0.156,0.198 10 false 4 5.021,1.375 5.177,1.573 0.156,0.198 10 false 3 5.042,2.271 5.198,2.469 0.156,0.198 10 false 1 5.031,3.083 5.188,3.281 0.156,0.198 10 false 2 2.083,2.417 3.417,2.625 1.333,0.208 10 false from NOx PM Relay 2,0.927 2.156,1.125 0.156,0.198 10 false 6 2,1.365 2.365,1.563 0.365,0.198 10 false 17 0.542,1.948 1,2.146 0.458,0.198 10 false Q41 0.542,2.094 2.99,2.292 2.448,0.198 10 false No. 7 Junction Connector 5.271,3.896 5.583,4.094 0.313,0.198 10 false s6 5.271,4.063 6.76,4.323 1.49,0.26 10 false Nitrogen Oxides Sensor

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


HINT:

Operating the engine switch, any switches or any doors triggers related ECU and sensor communication with the CAN, which causes resistance variation.


PROCEDURE

1.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL
a.

Disconnect the cable from the negative (-) battery terminal before measuring the resistances of the CAB main wire and the CAN branch wire.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the airbag system.


NOTICE:
·

After turning the engine switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).

·

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).





NEXT

2.CHECK FOR OPEN IN CAN BUS WIRE (NITROGEN OXIDES SENSOR CAN BRANCH WIRE)
2.CHECK FOR OPEN IN CAN BUS WIRE (NITROGEN OXIDES SENSOR CAN BRANCH WIRE)
a.
U169383E01
2.003,0.984 2.217,1.798 2.217,1.798 2.312,1.798 false 1.668,0.984 1.512,1.798 1.512,1.798 1.384,1.798 false 1.639,0.17 1.951,0.348 0.313,0.178 10 s6 0.875,1.692 1.474,1.870 0.599,0.178 10 CAN- 2.353,1.715 2.821,1.892 0.468,0.177 10 CAN+ 0.09,0.03 0.558,0.208 0.468,0.177 10 *a

Disconnect the nitrogen oxides sensor connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
s6-4 (CAN+) - s6-3 (CAN-) Engine switch off 54 to 69 Ω


Text in Illustration
*a Front view of wire harness connector
(to Nitrogen Oxides Sensor)



OK

3.CHECK HARNESS AND CONNECTOR (NITROGEN OXIDES SENSOR - BATTERY AND BODY GROUND)

NG

REPAIR OR REPLACE NITROGEN OXIDES SENSOR CAN BRANCH WIRE OR CONNECTOR (CAN+, CAN-)

3.CHECK HARNESS AND CONNECTOR (NITROGEN OXIDES SENSOR - BATTERY AND BODY GROUND)
a.
U169384E01
1.573,0.983 1.787,1.797 1.787,1.797 1.883,1.797 false 1.238,1.011 1.083,1.797 1.083,1.797 0.955,1.797 false 1.639,0.17 1.951,0.348 0.313,0.178 10 s6 0.483,1.723 0.922,1.901 0.439,0.178 10 BATT 1.905,1.714 2.372,1.891 0.468,0.177 10 GND 0.136,0.076 0.603,0.253 0.468,0.177 10 *a

Connect the cable to the negative (-) battery terminal.

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).



b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
s6-2 (GND) - Body ground Always Below 1 Ω



c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
s6-1 (BATT) - Body ground Engine switch on (IG) 11 to 14 V



Text in Illustration
*a Front view of wire harness connector
(to Nitrogen Oxides Sensor)


OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR