Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM(for RHD without Entry and Start System) › 2015.06–2017.08
RM27T0E _57 Power Source / Network _053729 NETWORKING _0261034 CAN COMMUNICATION SYSTEM(for RHD without Entry and Start System) J

NETWORKING  CAN COMMUNICATION SYSTEM(for RHD without Entry and Start System)  Steering Angle Sensor Communication Stop Mode  


DESCRIPTION

Detection Item Symptom Trouble Area
Steering Angle Sensor Communication Stop Mode Either condition is met:
·

"Spiral cable (Steering Angle Sensor)" is not displayed on "Bus Check".


·

"Steering Angle Sensor Communication Stop Mode" in "DTC Combination Table" applies.


·

Power source or inside spiral cable sub-assembly (steering angle sensor)

·

Spiral cable sub-assembly (steering angle sensor) CAN branch wire or connector

·

Spiral cable sub-assembly (steering angle sensor)



For vehicles with a vehicle stability control system (for hybrid brake booster) only.


WIRING DIAGRAM

C198942E77
5.292,2.695 5.686,2.871 0.395,0.176 10 G33 5.292,2.855 7.097,3.218 1.805,0.364 10 Spiral Cable Sub-assembly (Steering Angle Sensor) 0.619,1.381 1.019,1.557 0.400,0.176 10 G132 0.619,1.54 2.274,1.717 1.655,0.176 10 No. 2 Junction Connector 5.812,0.528 6.278,0.704 0.466,0.176 10 CANH 1.941,0.43 2.049,0.584 0.109,0.154 10 7 5.608,0.446 5.740,0.600 0.132,0.154 10 4 5.608,0.886 5.740,1.040 0.132,0.154 10 3 5.608,1.329 5.740,1.483 0.132,0.154 10 6 5.608,1.766 5.740,1.919 0.132,0.154 10 5 5.608,2.205 5.740,2.359 0.132,0.154 10 2 4.623,1.292 5.105,1.446 0.481,0.154 10 ECU-B 2.889,1.41 3.691,1.582 0.802,0.172 10 from Battery 2.345,1.848 3.742,2.020 1.397,0.172 10 from IG1 NO.1 Relay 4.442,1.72 5.351,1.874 0.910,0.154 10 ECU-IG NO.1 1.941,0.884 2.135,1.037 0.194,0.153 10 18 5.812,0.966 6.278,1.142 0.466,0.176 10 CANL 5.812,1.416 6.278,1.592 0.466,0.176 10 BAT 5.812,1.866 6.278,2.042 0.466,0.176 10 IG 5.812,2.309 6.278,2.485 0.466,0.176 10 ESS

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


HINT:

Operating the ignition switch, any switches or any doors triggers related ECU and sensor communication with the CAN, which causes resistance variation.


PROCEDURE

1.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL
a.

Disconnect the cable from the negative (-) battery terminal before measuring the resistances of the CAN main wire and the CAN branch wire.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the airbag system.


NOTICE:
·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).

·

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).





NEXT

2.CHECK FOR OPEN IN CAN BUS WIRE (STEERING ANGLE SENSOR CAN BRANCH WIRE)
2.CHECK FOR OPEN IN CAN BUS WIRE (STEERING ANGLE SENSOR CAN BRANCH WIRE)
a.
U148232E05
2.031,1.552 1.708,1.156 1.708,1.156 1.635,1.156 true 2.146,1.552 2.396,1.292 2.396,1.292 2.479,1.292 true 1.219,1.063 1.646,1.26 0.427,0.198 10 false CANH 0.896,1.448 1.219,1.646 0.323,0.198 10 false G33 0.083,0 0.51,0.198 0.427,0.198 10 false *a 2.51,1.208 2.927,1.406 0.417,0.198 10 false CANL

Disconnect the G33 spiral cable sub-assembly (steering angle sensor) connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
G33-4 (CANH) - G33-3 (CANL) Ignition switch off 54 to 69 Ω


Text in Illustration
*a Rear view of wire harness connector
(to Spiral Cable Sub-assembly [Steering Angle Sensor])



OK

3.CHECK HARNESS AND CONNECTOR (STEERING ANGLE SENSOR - BATTERY AND BODY GROUND)

NG

REPAIR OR REPLACE STEERING ANGLE SENSOR CAN BRANCH WIRE OR CONNECTOR (CANH, CANL)

3.CHECK HARNESS AND CONNECTOR (STEERING ANGLE SENSOR - BATTERY AND BODY GROUND)
a.
U169927E02
1.844,1.563 1.531,1.177 1.531,1.177 1.448,1.177 false 2.24,1.552 2.479,1.292 2.479,1.292 2.573,1.292 false 1.927,1.552 1.688,0.917 1.688,0.917 1.604,0.917 false 1.146,1.094 1.438,1.292 0.292,0.198 10 false BAT 0.927,1.51 1.229,1.708 0.302,0.198 10 false G33 1.427,0.833 1.604,1.031 0.177,0.198 10 false IG 0.083,0 0.51,0.198 0.427,0.198 10 false *a 2.615,1.208 3.031,1.406 0.417,0.198 10 false ESS

Connect the cable to the negative (-) battery terminal.

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).



b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G33-2 (ESS) - Body ground Always Below 1 Ω



c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
G33-6 (BAT) - Body ground Always 11 to 14 V
G33-5 (IG) - Body ground Ignition switch ON 11 to 14 V



Text in Illustration
*a Rear view of wire harness connector
(to Spiral Cable Sub-assembly [Steering Angle Sensor])


OK

REPLACE SPIRAL CABLE SUB-ASSEMBLY (STEERING ANGLE SENSOR)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR