Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM(for RHD without Entry and Start System) › 2015.06–2017.08
RM27T0E _57 Power Source / Network _053729 NETWORKING _0261034 CAN COMMUNICATION SYSTEM(for RHD without Entry and Start System) J

NETWORKING  CAN COMMUNICATION SYSTEM(for RHD without Entry and Start System)  Brake Actuator (Skid Control ECU) Communication Stop Mode  


DESCRIPTION

Detection Item Symptom Trouble Area
Brake Actuator (Skid Control ECU) Communication Stop Mode Either condition is met:
·

"Skid Control (ABS/VSC/TRAC)" is not displayed on "Bus Check".

·

"Brake Actuator (Skid Control ECU) Communication Stop Mode" in "DTC Combination Table" applies.


·

Power source or inside brake actuator assembly (skid control ECU)

·

Brake actuator assembly (skid control ECU) CAN branch wire or connector

·

Brake actuator assembly (skid control ECU)



For vehicles without a vehicle stability control system only.


WIRING DIAGRAM

C217558E03
5.813,2.84 6.279,3.016 0.466,0.176 10 GND1 5.388,3.799 5.782,3.975 0.395,0.176 10 A6 5.388,3.959 7.013,4.322 1.626,0.364 10 Brake Actuator Assembly (Skid Control ECU) 0.621,1.521 1.021,1.697 0.400,0.176 10 A72 0.621,1.68 2.276,1.857 1.655,0.176 10 No. 1 Junction Connector 5.813,0.668 6.279,0.844 0.466,0.176 10 CANH 1.942,0.57 2.222,0.724 0.280,0.154 10 11 5.534,1.019 5.734,1.172 0.200,0.154 10 14 5.534,0.575 5.734,0.729 0.200,0.154 10 25 5.534,1.886 5.734,2.040 0.200,0.154 10 12 5.813,1.976 6.279,2.152 0.466,0.176 10 +BS 5.534,1.466 5.734,1.620 0.200,0.154 10 24 4.754,1.432 5.467,1.586 0.713,0.154 10 ABS NO.1 4.754,1.843 5.467,1.997 0.713,0.154 10 ABS NO.2 2.917,1.55 3.719,1.722 0.802,0.172 10 from Battery 2.762,2.357 4.161,2.528 1.398,0.172 10 from IG1 NO.1 Relay 4.571,2.223 5.508,2.377 0.937,0.154 10 ECU-IG NO.1 5.534,2.272 5.717,2.426 0.183,0.154 10 34 5.576,2.742 5.734,2.896 0.158,0.154 10 1 5.534,3.156 5.734,3.310 0.200,0.154 10 13 1.942,1.024 2.136,1.177 0.194,0.153 10 22 5.813,1.106 6.279,1.282 0.466,0.176 10 CANL 5.813,1.556 6.279,1.732 0.466,0.176 10 BM 5.813,2.37 6.279,2.546 0.466,0.176 10 IG1 5.813,3.254 6.279,3.430 0.466,0.176 10 GND2

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


HINT:

Operating the ignition switch, any switches or any doors triggers related ECU and sensor communication with the CAN, which causes resistance variation.


PROCEDURE

1.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL
a.

Disconnect the cable from the negative (-) battery terminal before measuring the resistances of the CAN main wire and the CAN branch wire.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the airbag system.


NOTICE:
·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).

·

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).





NEXT

2.CHECK FOR OPEN IN CAN BUS WIRE (SKID CONTROL ECU CAN BRANCH WIRE)
2.CHECK FOR OPEN IN CAN BUS WIRE (SKID CONTROL ECU CAN BRANCH WIRE)
a.
U148256E01
0.118,0.031 0.316,0.229 0.198,0.198 10 *a 1.683,0.083 1.969,0.269 0.286,0.186 10 A6 0.218,1.676 0.658,1.822 0.440,0.147 10 CANL 0.408,1.871 0.848,2.040 0.440,0.169 10 CANH 1.315,1.343 1.042,1.944 1.042,1.944 0.936,1.944 false 1.315,1.217 0.8,1.754 0.8,1.754 0.722,1.754 false

Disconnect the A6 brake actuator assembly (skid control ECU) connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
A6-25 (CANH) - A6-14 (CANL) Ignition switch off 54 to 69 Ω


Text in Illustration
*a Front view of wire harness connector
(to Brake Actuator Assembly [Skid Control ECU])



OK

3.CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU - BATTERY AND BODY GROUND)

NG

REPAIR OR REPLACE SKID CONTROL ECU CAN BRANCH WIRE OR CONNECTOR (CANH, CANL)

3.CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU - BATTERY AND BODY GROUND)
a.
U148964E01
2.473,0.848 2.851,0.147 2.851,0.147 2.988,0.147 false 2.316,1.4 2.58,1.913 2.58,1.913 2.759,1.913 false 1.111,0.848 0.707,0.349 0.707,0.349 0.57,0.349 false 1.111,1.321 0.778,1.804 0.778,1.804 0.6,1.804 false 2.473,1.136 2.932,0.517 2.932,0.517 3.07,0.517 false 0.084,0.273 0.538,0.414 0.455,0.141 10 GND1 0.084,1.712 0.538,1.854 0.455,0.141 10 GND2 3.006,0.075 3.315,0.217 0.309,0.141 10 +BS 3.092,0.445 3.352,0.586 0.260,0.141 10 BM 2.782,1.833 3.237,1.974 0.455,0.141 10 IG1 1.703,0.129 1.890,0.270 0.187,0.141 10 A6

Connect the cable to the negative (-) battery terminal.

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).



b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A6-1 (GND1) - Body ground Always Below 1 Ω
A6-13 (GND2) - Body ground Always Below 1 Ω



c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A6-12 (+BS) - Body ground Always 11 to 14 V
A6-24 (BM) - Body ground Always 11 to 14 V
A6-34 (IG1) - Body ground Ignition switch ON 11 to 14 V



Text in Illustration
*a Front view of wire harness connector
(to Brake Actuator Assembly [Skid Control ECU])


OK

REPLACE BRAKE ACTUATOR ASSEMBLY (SKID CONTROL ECU)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR