Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM(for RHD without Entry and Start System) › 2015.06–2017.08
RM27T0E _57 Power Source / Network _053729 NETWORKING _0261034 CAN COMMUNICATION SYSTEM(for RHD without Entry and Start System) C

NETWORKING  CAN COMMUNICATION SYSTEM(for RHD without Entry and Start System)  U1002  Lost Communication with Gateway Module  


DESCRIPTION

·

The network gateway ECU stores this DTC when no signals can be received from the ECUs that have been memorized as those connected to the CAN V2 bus.

·

When the network gateway ECU receives a response signal from the ECUs connected to the CAN V2 bus, the network gateway ECU recognizes and memorizes that the ECU is connected to the CAN V2 bus. Based on this memorized data, the network gateway ECU monitors for malfunctions in the ECUs connected to the CAN V2 bus when communicating with those ECUs. If the network gateway ECU cannot receive response signals from the ECUs that have been memorized as those connected to the CAN V2 bus, the network gateway ECU determines that a malfunction exists.

·

If 2 or more DTCs are output during the DTC check, one side of the CAN branch wire may be open (one side of the CANH [CAN branch wire]/CANL [CAN branch wire] of the ECU and/or sensor is open).


DTC Code DTC Detection Condition Trouble Area
U1002 Lost communication with the gateway module.
·

V2 bus circuit

·

Network gateway ECU CAN main wire or connector

·

Clearance warning ECU assembly CAN branch wire or connector

·

Network gateway ECU

·

Clearance warning ECU assembly

·

No. 1 junction connector

·

No. 2 junction connector

·

No. 3 junction connector

·

No. 5 junction connector



For vehicles with a TOYOTA parking assist-sensor system (for 4 sensor type).


WIRING DIAGRAM

C292192E02
5.885,0.396 6.365,0.542 0.479,0.146 10 false CA2H 5.885,0.99 6.365,1.135 0.479,0.146 10 false CA2L 5.896,2.177 6.375,2.323 0.479,0.146 10 false CANH 5.896,2.833 6.375,2.979 0.479,0.146 10 false CANL 5.615,1.198 6.094,1.344 0.479,0.146 10 false G155 5.594,1.344 7.052,1.688 1.458,0.344 10 false Network Gateway ECU 5.594,0.396 5.771,0.542 0.177,0.146 10 false 13 5.594,0.802 5.771,0.948 0.177,0.146 10 false 12 3.885,0.406 3.979,0.552 0.094,0.146 10 false 3 3.823,0.802 4,0.948 0.177,0.146 10 false 14 4.667,0.406 4.844,0.552 0.177,0.146 10 false 1 4.625,0.802 4.802,0.948 0.177,0.146 10 false 12 2.25,0.417 2.344,0.563 0.094,0.146 10 false 2 2.188,0.802 2.365,0.948 0.177,0.146 10 false 13 3.021,0.396 3.198,0.542 0.177,0.146 10 false 1 3,0.802 3.177,0.948 0.177,0.146 10 false 12 5.667,2.219 5.823,2.49 0.156,0.271 10 false 3 5.667,2.625 5.823,2.823 0.156,0.198 10 false 2 4.656,2.219 4.833,2.365 0.177,0.146 10 false 1 4.656,2.625 4.833,2.771 0.177,0.146 10 false 12 3.885,2.219 4.083,2.531 0.198,0.313 10 false 2 3.802,2.615 3.979,2.76 0.177,0.146 10 false 13 3.01,2.229 3.188,2.417 0.177,0.188 10 false 3 3.021,2.625 3.198,2.771 0.177,0.146 10 false 14 0.271,1.219 0.75,1.365 0.479,0.146 10 false I1 0.24,1.365 1.781,1.708 1.542,0.344 10 false Clearance Warning ECU Assembly 1.125,0.458 1.427,0.656 0.302,0.198 10 false R1 1.385,0.396 1.646,0.75 0.26,0.354 10 false 3 1.396,0.792 1.573,0.938 0.177,0.146 10 false 5 1.115,0.865 1.479,1.083 0.365,0.219 10 false R2 3.677,1.229 5.281,1.552 1.604,0.323 10 false G98 3.677,1.375 5.281,1.698 1.604,0.323 10 false No. 3 Junction Connector 1.854,3.052 3.458,3.375 1.604,0.323 10 false G95 1.854,3.229 3.458,3.552 1.604,0.323 10 false No. 2 Junction Connector 3.604,3.063 5.208,3.385 1.604,0.323 10 false A72 3.594,3.198 5.198,3.521 1.604,0.323 10 false No. 1 Junction Connector 5.438,3.073 7.042,3.396 1.604,0.323 10 false G102 5.469,3.24 7.073,3.563 1.604,0.323 10 false No. 5 Junction Connector

CAUTION / NOTICE / HINT

HINT:

Operating the ignition switch, any switches or any doors triggers related ECU and sensor communication with the CAN, which causes resistance variation.


PROCEDURE

1.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL
a.

Disconnect the cable from the negative (-) battery terminal before measuring the resistances of the CAN main wire and the CAN branch wire.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the airbag system.


NOTICE:
·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).

·

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).





NEXT

2.CHECK CAN BUS WIRE (CHECK CAN MAIN WIRE FOR DISCONNECTION, CHECK BUS LINE FOR SHORT)
2.CHECK CAN BUS WIRE (CHECK CAN MAIN WIRE FOR DISCONNECTION, CHECK BUS LINE FOR SHORT)
a.
U170279E01
1.386,0.948 1.116,0.586 1.116,0.586 1.017,0.586 false 2.062,0.948 2.332,0.586 2.332,0.586 2.431,0.586 false 1.659,1.08 1.923,1.592 1.923,1.592 2.003,1.592 false 1.562,1.08 1.298,1.592 1.298,1.592 1.219,1.592 false 2.022,1.51 2.388,1.651 0.366,0.140 10 CA2L 0.733,1.51 1.124,1.651 0.390,0.140 10 CA2H 0.62,0.505 1.010,0.645 0.390,0.140 10 GND 2.452,0.505 2.842,0.645 0.390,0.140 10 BATT 0.063,0.042 0.369,0.182 0.306,0.140 10 *a 1.488,0.39 1.851,0.527 0.363,0.137 10 G155

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition Resistance: Malfunction
G155-13 (CA2H) - G155-12 (CA2L) Ignition switch off 54 to 69 Ω Below 53 Ω: Short in line
G155-13 (CA2H) - G155-12 (CA2L) Ignition switch off 54 to 69 Ω Higher than 70 Ω: Open in CAN main bus line
G155-13 (CA2H) - G155-2 (BATT) Ignition switch off 6 kΩ or higher Below 6 kΩ: +B short
G155-12 (CA2L) - G155-2 (BATT) Ignition switch off 6 kΩ or higher Below 6 kΩ: +B short
G155-13 (CA2H) - G155-4 (GND) Ignition switch off 200 Ω or higher Below 200 Ω: Ground short
G155-12 (CA2L) - G155-4 (GND) Ignition switch off 200 Ω or higher Below 200 Ω: Ground short


Text in Illustration
*a Component with harness connected
(Network Gateway ECU)

Result
Result Proceed to
NG
·

Open in CAN main bus line


A
NG
·

Short in line

·

+B short

·

GND short


B
OK C



A

3.CHECK FOR OPEN IN CAN BUS WIRE (NO. 2 JUNCTION CONNECTOR - NETWORK GATEWAY ECU)

B

15.CHECK FOR SHORT IN CAN BUS WIRES (NO. 1 JUNCTION CONNECTOR SIDE)

C

30.CHECK HARNESS AND CONNECTOR (NETWORK GATEWAY ECU - BATTERY AND BODY GROUND)
3.CHECK FOR OPEN IN CAN BUS WIRE (NO. 2 JUNCTION CONNECTOR - NETWORK GATEWAY ECU)
a.
U170280E01
2.525,1.049 2.424,1.049 2.424,1.049 2.272,1.234 false 2.272,1.439 2.446,1.672 2.446,1.672 2.569,1.672 false 2.543,0.971 2.963,1.108 0.421,0.137 10 CANH 2.58,1.59 2.976,1.727 0.396,0.137 10 CANL 0.062,0.08 0.458,0.217 0.396,0.137 10 *a 0.448,1.259 0.728,1.396 0.280,0.137 10 G95

Disconnect the G95 No. 2 junction connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
G95-1 (CANH) - G95-12 (CANL) Ignition switch off 108 to 132 Ω


Text in Illustration
*a Rear view of wire harness connector
(to No. 2 Junction Connector)



OK

4.CHECK FOR OPEN IN CAN BUS WIRE (NO. 2 JUNCTION CONNECTOR - NO. 5 JUNCTION CONNECTOR)

NG

5.CONNECT CONNECTOR
4.CHECK FOR OPEN IN CAN BUS WIRE (NO. 2 JUNCTION CONNECTOR - NO. 5 JUNCTION CONNECTOR)
a.
U170281E01
2.458,0.905 2.357,0.905 2.357,0.905 2.062,1.234 false 2.062,1.439 2.319,1.756 2.319,1.756 2.442,1.756 false 2.476,0.828 2.896,0.964 0.421,0.137 10 CANH 2.453,1.674 2.849,1.811 0.396,0.137 10 CANL 0.062,0.08 0.458,0.217 0.396,0.137 10 *a 0.448,1.259 0.728,1.396 0.280,0.137 10 G95

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
G95-3 (CANH) - G95-14 (CANL) Ignition switch off 108 to 132 Ω


Text in Illustration
*a Rear view of wire harness connector
(to No. 2 Junction Connector)



OK

REPLACE NO. 2 JUNCTION CONNECTOR

NG

10.CONNECT CONNECTOR
5.CONNECT CONNECTOR
a.

Reconnect the G95 No. 2 junction connector.



NEXT

6.CHECK FOR OPEN IN CAN BUS WIRE (NO. 3 JUNCTION CONNECTOR - NETWORK GATEWAY ECU)
6.CHECK FOR OPEN IN CAN BUS WIRE (NO. 3 JUNCTION CONNECTOR - NETWORK GATEWAY ECU)
a.
U170282E01
2.525,1.049 2.424,1.049 2.424,1.049 2.272,1.234 false 2.272,1.439 2.446,1.672 2.446,1.672 2.569,1.672 false 2.543,0.971 2.963,1.108 0.421,0.137 10 CANH 2.58,1.59 2.976,1.727 0.396,0.137 10 CANL 0.062,0.08 0.458,0.217 0.396,0.137 10 *a 0.448,1.259 0.728,1.396 0.280,0.137 10 G98

Disconnect the G98 No. 3 junction connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
G98-1 (CANH) - G98-12 (CANL) Ignition switch off 108 to 132 Ω


Text in Illustration
*a Rear view of wire harness connector
(to No. 3 Junction Connector)



OK

7.CHECK FOR OPEN IN CAN BUS WIRE (NO. 3 JUNCTION CONNECTOR - NO. 2 JUNCTION CONNECTOR)

NG

8.CONNECT CONNECTOR
7.CHECK FOR OPEN IN CAN BUS WIRE (NO. 3 JUNCTION CONNECTOR - NO. 2 JUNCTION CONNECTOR)
a.
U170283E01
2.458,0.905 2.357,0.905 2.357,0.905 2.062,1.234 false 2.062,1.439 2.319,1.756 2.319,1.756 2.442,1.756 false 2.476,0.828 2.896,0.964 0.421,0.137 10 CANH 2.453,1.674 2.849,1.811 0.396,0.137 10 CANL 0.062,0.08 0.458,0.217 0.396,0.137 10 *a 0.448,1.259 0.728,1.396 0.280,0.137 10 G98

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
G98-3 (CANH) - G98-14 (CANL) Ignition switch off 108 to 132 Ω


Text in Illustration
*a Rear view of wire harness connector
(to No. 3 Junction Connector)



OK

REPLACE NO. 3 JUNCTION CONNECTOR

NG

REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR (NO. 3 JUNCTION CONNECTOR - NO. 2 JUNCTION CONNECTOR)

8.CONNECT CONNECTOR
a.

Reconnect the G98 No. 3 junction connector.



NEXT

9.CHECK FOR OPEN IN CAN BUS WIRE (NETWORK GATEWAY ECU)
9.CHECK FOR OPEN IN CAN BUS WIRE (NETWORK GATEWAY ECU)
a.
U170301E01
0.447,1.121 0.807,1.259 0.360,0.137 10 G155 1.59,1.278 1.186,1.588 1.186,1.588 1.063,1.588 false 1.235,1.843 1.409,1.843 1.409,1.843 1.699,1.276 false 0.573,1.514 0.962,1.651 0.389,0.137 10 CA2H 0.785,1.757 1.174,1.895 0.389,0.137 10 CA2L 0.087,0.073 0.388,0.210 0.301,0.137 10 *a

Disconnect the G155 network gateway ECU connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
G155-13 (CA2H) - G155- 12 (CA2L) Ignition switch off 108 to 132 Ω


Text in Illustration
*a Rear view of wire harness connector
(to Network Gateway ECU)



OK

NG

REPAIR OR REPLACE CAN MAIN WIRE CONNECTED TO NETWORK GATEWAY ECU (NETWORK GATEWAY ECU - NO. 3 JUNCTION CONNECTOR)

10.CONNECT CONNECTOR
a.

Reconnect the G95 No. 2 junction connector.



NEXT

11.CHECK FOR OPEN IN CAN BUS WIRE (NO. 1 JUNCTION CONNECTOR - NO. 5 JUNCTION CONNECTOR)
11.CHECK FOR OPEN IN CAN BUS WIRE (NO. 1 JUNCTION CONNECTOR - NO. 5 JUNCTION CONNECTOR)
a.
U170284E01
2.525,1.049 2.424,1.049 2.424,1.049 2.272,1.234 false 2.272,1.439 2.446,1.672 2.446,1.672 2.569,1.672 false 2.543,0.971 2.963,1.108 0.421,0.137 10 CANH 2.58,1.59 2.976,1.727 0.396,0.137 10 CANL 0.062,0.08 0.458,0.217 0.396,0.137 10 *a 0.448,1.259 0.728,1.396 0.280,0.137 10 A72

Disconnect the A72 No. 1 junction connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
A72-1 (CANH) - A72-12 (CANL) Ignition switch off 108 to 132 Ω


Text in Illustration
*a Rear view of wire harness connector
(to No. 1 Junction Connector)



OK

12.CHECK FOR OPEN IN CAN BUS WIRE (NO. 1 JUNCTION CONNECTOR - NO. 2 JUNCTION CONNECTOR)

NG

13.CONNECT CONNECTOR
12.CHECK FOR OPEN IN CAN BUS WIRE (NO. 1 JUNCTION CONNECTOR - NO. 2 JUNCTION CONNECTOR)
a.
U170285E01
2.456,1.015 2.355,1.015 2.355,1.015 2.169,1.234 false 2.169,1.439 2.343,1.672 2.343,1.672 2.466,1.672 false 2.474,0.937 2.894,1.074 0.421,0.137 10 CANH 2.477,1.59 2.873,1.727 0.396,0.137 10 CANL 0.062,0.08 0.458,0.217 0.396,0.137 10 *a 0.451,1.259 0.721,1.396 0.269,0.137 10 A72

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
A72-2 (CANH) - A72-13 (CANL) Ignition switch off 108 to 132 Ω


Text in Illustration
*a Rear view of wire harness connector
(to No. 1 Junction Connector)



OK

REPLACE NO. 1 JUNCTION CONNECTOR

NG

REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR (NO. 1 JUNCTION CONNECTOR - NO. 2 JUNCTION CONNECTOR)

13.CONNECT CONNECTOR
a.

Reconnect the A72 No. 1 junction connector.



NEXT

14.CHECK FOR OPEN IN CAN BUS WIRE (NO. 5 JUNCTION CONNECTOR)
14.CHECK FOR OPEN IN CAN BUS WIRE (NO. 5 JUNCTION CONNECTOR)
a.
U170275E02
1.333,0.813 1.104,0.521 1.104,0.521 0.979,0.521 false 1.302,0.177 1.427,0.177 1.427,0.177 1.604,0.802 false 0.531,0.448 1.042,0.76 0.51,0.313 10 false CANH 0.875,0.094 1.427,0.354 0.552,0.26 10 false CANL 0.094,0.104 0.646,0.354 0.552,0.25 10 false *a 0.354,0.979 0.76,1.281 0.406,0.302 10 false G102

Disconnect the G102 No. 5 junction connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
G102-3 (CANH) - G102-2 (CANL) Ignition switch off 108 to 132 Ω


Text in Illustration
*a Rear view of wire harness connector
(to No. 5 Junction Connector)



OK

REPLACE NO. 5 JUNCTION CONNECTOR

NG

REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR (NO. 5 JUNCTION CONNECTOR - NO. 1 JUNCTION CONNECTOR)

15.CHECK FOR SHORT IN CAN BUS WIRES (NO. 1 JUNCTION CONNECTOR SIDE)
a.
U170279E01
1.386,0.948 1.116,0.586 1.116,0.586 1.017,0.586 false 2.062,0.948 2.332,0.586 2.332,0.586 2.431,0.586 false 1.659,1.08 1.923,1.592 1.923,1.592 2.003,1.592 false 1.562,1.08 1.298,1.592 1.298,1.592 1.219,1.592 false 2.022,1.51 2.388,1.651 0.366,0.140 10 CA2L 0.733,1.51 1.124,1.651 0.390,0.140 10 CA2H 0.62,0.505 1.010,0.645 0.390,0.140 10 GND 2.452,0.505 2.842,0.645 0.390,0.140 10 BATT 0.063,0.042 0.369,0.182 0.306,0.140 10 *a 1.488,0.39 1.851,0.527 0.363,0.137 10 G155

Disconnect the A72 No. 1 junction connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
G155-13 (CA2H) - G155-12 (CA2L) Ignition switch off 108 to 132 Ω
G155-13 (CA2H) - G155-4 (GND) Ignition switch off 200 Ω or higher
G155-12 (CA2L) - G155-4 (GND) Ignition switch off 200 Ω or higher
G155-13 (CA2H) - G155-2 (BATT) Ignition switch off 6 kΩ or higher
G155-12 (CA2L) - G155-2 (BATT) Ignition switch off 6 kΩ or higher


Text in Illustration
*a Component with harness connected
(Network Gateway ECU)



OK

16.CHECK FOR SHORT IN CAN BUS WIRES (NO. 1 JUNCTION CONNECTOR - NO. 5 JUNCTION CONNECTOR)

NG

19.CONNECT CONNECTOR
16.CHECK FOR SHORT IN CAN BUS WIRES (NO. 1 JUNCTION CONNECTOR - NO. 5 JUNCTION CONNECTOR)
a.
U170333E01
1.673,2.512 1.488,2.164 1.488,2.164 1.348,2.164 false 2.211,2.959 2.348,3.208 2.348,3.208 2.489,3.208 false 2.213,1.291 2.337,1.495 2.337,1.495 2.434,1.495 false 2.48,0.951 2.365,0.951 2.365,0.951 2.213,1.103 false 0.045,0.06 0.282,0.297 0.237,0.237 10 *a 0.045,1.892 0.282,2.129 0.237,0.237 10 *b 2.501,0.874 2.921,1.016 0.420,0.142 10 CANH 2.452,1.409 2.876,1.551 0.424,0.142 10 CANL 2.523,3.14 2.947,3.282 0.424,0.142 10 BAT 0.402,2.702 0.684,2.840 0.282,0.138 10 G48 1.062,2.087 1.291,2.229 0.229,0.142 10 CG 0.554,1.104 0.819,1.242 0.265,0.138 10 A72

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
A72-1 (CANH) - A72-12 (CANL) Ignition switch off 108 to 132 Ω
A72-1 (CANH) - G48-4 (CG) Ignition switch off 200 Ω or higher
A72-12 (CANL) - G48-4 (CG) Ignition switch off 200 Ω or higher
A72-1 (CANH) - G48-16 (BAT) Ignition switch off 6 kΩ or higher
A72-12 (CANL) - G48-16 (BAT) Ignition switch off 6 kΩ or higher


Text in Illustration
*a Rear view of wire harness connector
(to No. 1 Junction Connector)
*b Front view of DLC3



OK

REPLACE NO. 1 JUNCTION CONNECTOR

NG

17.CONNECT CONNECTOR
17.CONNECT CONNECTOR
a.

Reconnect the A72 No. 1 junction connector.



NEXT

18.CHECK FOR SHORT IN CAN BUS WIRES (NO. 5 JUNCTION CONNECTOR)
18.CHECK FOR SHORT IN CAN BUS WIRES (NO. 5 JUNCTION CONNECTOR)
a.
U170304E01
1.334,2.154 1.426,2.154 1.426,2.154 1.665,2.524 false 2.219,2.959 2.357,3.208 2.357,3.208 2.497,3.208 false 1.377,0.874 1.146,1.126 1.146,1.126 0.963,1.126 false 1.215,0.358 1.373,0.358 1.373,0.358 1.691,0.708 false 0.062,0.06 0.299,0.297 0.237,0.237 10 *a 0.062,1.892 0.299,2.129 0.237,0.237 10 *b 0.76,0.272 1.148,0.414 0.389,0.142 10 CANL 0.445,1.049 0.869,1.191 0.424,0.142 10 CANH 1.045,2.078 1.469,2.220 0.424,0.142 10 CG 2.532,3.14 2.955,3.282 0.424,0.142 10 BAT 0.407,2.69 0.689,2.830 0.282,0.140 10 G48 2.564,0.773 2.938,0.913 0.374,0.140 10 G102

Disconnect the G102 No. 5 junction connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
G102-3 (CANH) - G102-2 (CANL) Ignition switch off 108 to 132 Ω
G102-3 (CANH) - G48-4 (CG) Ignition switch off 200 Ω or higher
G102-2 (CANL) - G48-4 (CG) Ignition switch off 200 Ω or higher
G102-3 (CANH) - G48-16 (BAT) Ignition switch off 6 kΩ or higher
G102-2 (CANL) - G48-16 (BAT) Ignition switch off 6 kΩ or higher


Text in Illustration
*a Rear view of wire harness connector
(to No. 5 Junction Connector)
*b Front view of DLC3



OK

REPLACE NO. 5 JUNCTION CONNECTOR

NG

REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR (NO. 5 JUNCTION CONNECTOR - NO. 1 JUNCTION CONNECTOR)

19.CONNECT CONNECTOR
a.

Reconnect the A72 No. 1 junction connector.



NEXT

20.CHECK FOR SHORT IN CAN BUS WIRES (NO. 2 JUNCTION CONNECTOR - NO. 1 JUNCTION CONNECTOR)
20.CHECK FOR SHORT IN CAN BUS WIRES (NO. 2 JUNCTION CONNECTOR - NO. 1 JUNCTION CONNECTOR)
a.
U170334E01
1.673,2.512 1.488,2.164 1.488,2.164 1.348,2.164 false 2.211,2.959 2.348,3.208 2.348,3.208 2.489,3.208 false 2.019,1.291 2.225,1.576 2.225,1.576 2.323,1.576 false 2.406,0.797 2.292,0.797 2.292,0.797 2.019,1.103 false 0.045,0.06 0.282,0.297 0.237,0.237 10 *a 0.045,1.892 0.282,2.129 0.237,0.237 10 *b 2.428,0.719 2.848,0.861 0.420,0.142 10 CANH 2.34,1.49 2.764,1.632 0.424,0.142 10 CANL 2.523,3.14 2.947,3.282 0.424,0.142 10 BAT 0.402,2.702 0.684,2.840 0.282,0.138 10 G48 1.062,2.087 1.291,2.229 0.229,0.142 10 CG 0.531,1.104 0.813,1.242 0.282,0.138 10 G95

Disconnect the G95 No. 2 junction connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
G95-3 (CANH) - G95-14 (CANL) Ignition switch off 108 to 132 Ω
G95-3 (CANH) - G48-4 (CG) Ignition switch off 200 Ω or higher
G95-14 (CANL) - G48-4 (CG) Ignition switch off 200 Ω or higher
G95-3 (CANH) - G48-16 (BAT) Ignition switch off 6 kΩ or higher
G95-14 (CANL) - G48-16 (BAT) Ignition switch off 6 kΩ or higher


Text in Illustration
*a Rear view of wire harness connector
(to No. 2 Junction Connector)
*b Front view of DLC3



OK

21.CHECK FOR SHORT IN CAN BUS WIRES (NO. 2 JUNCTION CONNECTOR SIDE)

NG

REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR (NO. 2 JUNCTION CONNECTOR - NO. 1 JUNCTION CONNECTOR)

21.CHECK FOR SHORT IN CAN BUS WIRES (NO. 2 JUNCTION CONNECTOR SIDE)
a.
U170279E01
1.386,0.948 1.116,0.586 1.116,0.586 1.017,0.586 false 2.062,0.948 2.332,0.586 2.332,0.586 2.431,0.586 false 1.659,1.08 1.923,1.592 1.923,1.592 2.003,1.592 false 1.562,1.08 1.298,1.592 1.298,1.592 1.219,1.592 false 2.022,1.51 2.388,1.651 0.366,0.140 10 CA2L 0.733,1.51 1.124,1.651 0.390,0.140 10 CA2H 0.62,0.505 1.010,0.645 0.390,0.140 10 GND 2.452,0.505 2.842,0.645 0.390,0.140 10 BATT 0.063,0.042 0.369,0.182 0.306,0.140 10 *a 1.488,0.39 1.851,0.527 0.363,0.137 10 G155

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
G155-13 (CA2H) - G155-12 (CA2L) Ignition switch off 108 to 132 Ω
G155-13 (CA2H) - G155-4 (GND) Ignition switch off 200 Ω or higher
G155-12 (CA2L) - G155-4 (GND) Ignition switch off 200 Ω or higher
G155-13 (CA2H) - G155-2 (BATT) Ignition switch off 6 kΩ or higher
G155-12 (CA2L) - G155-2 (BATT) Ignition switch off 6 kΩ or higher


Text in Illustration
*a Component with harness connected
(Network Gateway ECU)



OK

22.CHECK FOR SHORT IN CAN BUS WIRES (NO. 2 JUNCTION CONNECTOR - CLEARANCE WARNING ECU ASSEMBLY)

NG

25.CONNECT CONNECTOR
22.CHECK FOR SHORT IN CAN BUS WIRES (NO. 2 JUNCTION CONNECTOR - CLEARANCE WARNING ECU ASSEMBLY)
a.
U170366E01
1.673,2.512 1.488,2.164 1.488,2.164 1.348,2.164 false 2.211,2.959 2.348,3.208 2.348,3.208 2.489,3.208 false 2.122,1.291 2.298,1.576 2.298,1.576 2.396,1.576 false 2.437,0.913 2.322,0.913 2.322,0.913 2.122,1.103 false 0.045,0.06 0.282,0.297 0.237,0.237 10 *a 0.045,1.892 0.282,2.129 0.237,0.237 10 *b 2.459,0.835 2.878,0.977 0.420,0.142 10 CANH 2.413,1.49 2.837,1.632 0.424,0.142 10 CANL 2.523,3.14 2.947,3.282 0.424,0.142 10 BAT 0.402,2.702 0.684,2.840 0.282,0.138 10 G48 1.062,2.087 1.291,2.229 0.229,0.142 10 CG 0.531,1.104 0.813,1.242 0.282,0.138 10 G95

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
G95-2 (CANH) - G95-13 (CANL) Ignition switch off 200 Ω or higher
G95-2 (CANH) - G48-4 (CG) Ignition switch off 200 Ω or higher
G95-13 (CANL) - G48-4 (CG) Ignition switch off 200 Ω or higher
G95-2 (CANH) - G48-16 (BAT) Ignition switch off 6 kΩ or higher
G95-13 (CANL) - G48-16 (BAT) Ignition switch off 6 kΩ or higher


Text in Illustration
*a Rear view of wire harness connector
(to No. 2 Junction Connector)
*b Front view of DLC3



OK

REPLACE NO. 2 JUNCTION CONNECTOR

NG

23.CONNECT CONNECTOR
23.CONNECT CONNECTOR
a.

Reconnect the G95 No. 2 junction connector.



NEXT

24.CHECK FOR SHORT IN CAN BUS WIRES (CLEARANCE WARNING ECU ASSEMBLY)
24.CHECK FOR SHORT IN CAN BUS WIRES (CLEARANCE WARNING ECU ASSEMBLY)
a.
U170320E01
1.185,1.047 0.88,0.749 0.88,0.749 0.729,0.749 false 0.483,0.667 0.681,0.804 0.198,0.137 10 R1 0.726,0.362 0.923,0.498 0.196,0.137 10 R2 0.064,0.068 0.506,0.205 0.442,0.137 10 *a 1.682,0.343 1.820,0.479 0.138,0.137 10 I1 0.064,1.878 0.506,2.015 0.442,0.137 10 *b 0.422,2.566 0.704,2.702 0.281,0.137 10 G48 2.213,2.858 2.377,3.15 2.377,3.15 2.531,3.15 false 2.554,3.071 2.942,3.208 0.389,0.137 10 BAT 0.987,2 1.376,2.136 0.389,0.137 10 CG 1.669,2.448 1.46,2.074 1.46,2.074 1.305,2.074 false 1.408,1.047 1.119,0.447 1.119,0.447 0.969,0.447 false

Disconnect the I1 clearance warning ECU assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
I1-3 (R1) - I1-5 (R2) Ignition switch off 54 to 69 Ω
I1-3 (R1) - G48-4 (CG) Ignition switch off 200 Ω or higher
I1-5 (R2) - G48-4 (CG) Ignition switch off 200 Ω or higher
I1-3 (R1) - G48-16 (BAT) Ignition switch off 6 kΩ or higher
I1-5 (R2) - G48-16 (BAT) Ignition switch off 6 kΩ or higher


Text in Illustration
*a Front view of wire harness connector
(to Clearance Warning ECU Assembly)
*b Front view of DLC3



OK

NG

REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO CLEARANCE WARNING ECU ASSEMBLY (R1, R2)

25.CONNECT CONNECTOR
a.

Reconnect the G95 No. 2 junction connector.



NEXT

26.CHECK FOR SHORT IN CAN BUS WIRES (NO. 3 JUNCTION CONNECTOR - NO. 2 JUNCTION CONNECTOR)
26.CHECK FOR SHORT IN CAN BUS WIRES (NO. 3 JUNCTION CONNECTOR - NO. 2 JUNCTION CONNECTOR)
a.
U170335E01
1.673,2.512 1.488,2.164 1.488,2.164 1.348,2.164 false 2.211,2.959 2.348,3.208 2.348,3.208 2.489,3.208 false 2.019,1.291 2.225,1.576 2.225,1.576 2.323,1.576 false 2.406,0.797 2.292,0.797 2.292,0.797 2.019,1.103 false 0.045,0.06 0.282,0.297 0.237,0.237 10 *a 0.045,1.892 0.282,2.129 0.237,0.237 10 *b 2.428,0.719 2.848,0.861 0.420,0.142 10 CANH 2.34,1.49 2.764,1.632 0.424,0.142 10 CANL 2.523,3.14 2.947,3.282 0.424,0.142 10 BAT 0.402,2.702 0.684,2.840 0.282,0.138 10 G48 1.062,2.087 1.291,2.229 0.229,0.142 10 CG 0.531,1.104 0.813,1.242 0.282,0.138 10 G98

Disconnect the G98 No. 3 junction connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
G98-3 (CANH) - G98-14 (CANL) Ignition switch off 108 to 132 Ω
G98-3 (CANH) - G48-4 (CG) Ignition switch off 200 Ω or higher
G98-14 (CANL) - G48-4 (CG) Ignition switch off 200 Ω or higher
G98-3 (CANH) - G48-16 (BAT) Ignition switch off 6 kΩ or higher
G98-14 (CANL) - G48-16 (BAT) Ignition switch off 6 kΩ or higher


Text in Illustration
*a Rear view of wire harness connector
(to No. 3 Junction Connector)
*b Front view of DLC3



OK

27.CHECK FOR SHORT IN CAN BUS WIRES (NO. 3 JUNCTION CONNECTOR - NETWORK GATEWAY ECU)

NG

REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR (NO. 3 JUNCTION CONNECTOR - NO. 2 JUNCTION CONNECTOR)

27.CHECK FOR SHORT IN CAN BUS WIRES (NO. 3 JUNCTION CONNECTOR - NETWORK GATEWAY ECU)
a.
U170336E01
1.673,2.512 1.488,2.164 1.488,2.164 1.348,2.164 false 2.211,2.959 2.348,3.208 2.348,3.208 2.489,3.208 false 2.213,1.291 2.384,1.507 2.384,1.507 2.482,1.507 false 2.482,0.915 2.367,0.915 2.367,0.915 2.208,1.103 false 0.045,0.06 0.282,0.297 0.237,0.237 10 *a 0.045,1.892 0.282,2.129 0.237,0.237 10 *b 2.504,0.837 2.923,0.979 0.420,0.142 10 CANH 2.499,1.421 2.923,1.563 0.424,0.142 10 CANL 2.523,3.14 2.947,3.282 0.424,0.142 10 BAT 0.402,2.702 0.684,2.840 0.282,0.138 10 G48 1.062,2.087 1.291,2.229 0.229,0.142 10 CG 0.531,1.104 0.813,1.242 0.282,0.138 10 G98

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
G98-1 (CANH) - G98-12 (CANL) Ignition switch off 108 to 132 Ω
G98-1 (CANH) - G48-4 (CG) Ignition switch off 200 Ω or higher
G98-12 (CANL) - G48-4 (CG) Ignition switch off 200 Ω or higher
G98-1 (CANH) - G48-16 (BAT) Ignition switch off 6 kΩ or higher
G98-12 (CANL) - G48-16 (BAT) Ignition switch off 6 kΩ or higher


Text in Illustration
*a Rear view of wire harness connector
(to No. 3 Junction Connector)
*b Front view of DLC3



OK

REPLACE NO. 3 JUNCTION CONNECTOR

NG

28.CONNECT CONNECTOR
28.CONNECT CONNECTOR
a.

Reconnect the G98 No. 3 junction connector.



NEXT

29.CHECK FOR SHORT IN CAN BUS WIRES (NETWORK GATEWAY ECU)
29.CHECK FOR SHORT IN CAN BUS WIRES (NETWORK GATEWAY ECU)
a.
U170306E01
2.572,1.04 2.931,1.177 0.359,0.137 10 G155 1.334,2.154 1.426,2.154 1.426,2.154 1.665,2.524 false 2.219,2.959 2.357,3.208 2.357,3.208 2.497,3.208 false 1.518,1.199 1.147,1.448 1.147,1.448 0.998,1.448 false 1.623,1.199 1.411,1.713 1.411,1.713 1.245,1.713 false 0.045,0.06 0.282,0.297 0.237,0.237 10 *a 0.045,1.892 0.282,2.129 0.237,0.237 10 *b 0.499,1.362 0.923,1.504 0.424,0.142 10 CA2H 0.763,1.627 1.187,1.769 0.424,0.142 10 CA2L 1.045,2.078 1.469,2.220 0.424,0.142 10 CG 2.532,3.14 2.955,3.282 0.424,0.142 10 BAT 0.405,2.689 0.684,2.829 0.280,0.140 10 G48

Disconnect the G155 network gateway ECU connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
G155-13 (CA2H) - G155-12 (CA2L) Ignition switch off 108 to 132 Ω
G155-13 (CA2H) - G48-4 (CG) Ignition switch off 200 Ω or higher
G155-12 (CA2L) - G48-4 (CG) Ignition switch off 200 Ω or higher
G155-13 (CA2H) - G48-16 (BAT) Ignition switch off 6 kΩ or higher
G155-12 (CA2L) - G48-16 (BAT) Ignition switch off 6 kΩ or higher


Text in Illustration
*a Rear view of wire harness connector
(to Network Gateway ECU)
*b Front view of DLC3



OK

NG

REPAIR OR REPLACE CAN MAIN WIRE CONNECTED TO NETWORK GATEWAY ECU (CA2H, CA2L)

30.CHECK HARNESS AND CONNECTOR (NETWORK GATEWAY ECU - BATTERY AND BODY GROUND)
a.
U170302E01
2.037,1.295 2.43,1.583 2.43,1.583 2.553,1.583 false 2.215,1.935 2.144,1.935 2.144,1.935 1.929,1.293 false 2.567,1.508 2.956,1.646 0.389,0.137 10 IG2 2.61,0.709 2.999,0.846 0.389,0.137 10 BATT 0.604,0.709 0.993,0.846 0.389,0.137 10 GND 2.234,1.866 2.623,2.004 0.389,0.137 10 IG1 0.497,1.136 0.856,1.273 0.360,0.137 10 G155 0.07,0.056 0.371,0.193 0.301,0.137 10 *a 1.35,1.097 1.101,0.786 1.101,0.786 1.029,0.786 false 2.278,1.097 2.527,0.786 2.527,0.786 2.598,0.786 false

Connect the cable to the negative (-) battery terminal.

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).



b.

Disconnect the G155 network gateway ECU connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G155-4 (GND) - Body ground Always Below 1 Ω



d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
G155-2 (BATT) - Body ground Always 11 to 14 V
G155-10 (IG1) - Body ground Ignition switch ON 11 to 14 V
G155-9 (IG2) - Body ground Ignition switch ON 11 to 14 V



Text in Illustration
*a Rear view of wire harness connector
(to Network Gateway ECU)


OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR