Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM(for RHD without Entry and Start System) › 2015.06–2017.08
RM27T0E _57 Power Source / Network _053729 NETWORKING _0261034 CAN COMMUNICATION SYSTEM(for RHD without Entry and Start System) J

NETWORKING  CAN COMMUNICATION SYSTEM(for RHD without Entry and Start System)  Audio Receiver Assembly Communication Stop Mode  


DESCRIPTION

Detection Item Symptom Trouble Area
Audio Receiver Assembly Communication Stop Mode Either condition is met:
·

"Display and Navigation (AVN1)" is not displayed on "Bus Check".

·

"Audio Receiver Assembly Communication Stop Mode" in "DTC Combination Table" applies.


·

Power source or inside radio and display receiver assembly

·

Radio and display receiver assembly CAN branch wire or connector

·

Radio and display receiver assembly



For vehicles with an audio and visual system (for radio and display type).


WIRING DIAGRAM

C280381E53
5.427,5.969 6.656,6.365 1.229,0.396 10 false Radio and Display Receiver Assembly 5.646,5.073 7,5.458 1.354,0.385 10 false GND1 5.646,4.25 7,4.635 1.354,0.385 10 false IG 5.615,3.427 6.969,3.813 1.354,0.385 10 false ACC1 5.646,2.583 7,2.969 1.354,0.385 10 false +B1 5.646,1.438 7,1.823 1.354,0.385 10 false CANL 5.656,0.833 7.01,1.219 1.354,0.385 10 false CANH 1.677,0.698 3.031,1.083 1.354,0.385 10 false 9 1.667,1.271 3.021,1.656 1.354,0.385 10 false 20 0.438,1.771 1.792,2.156 1.354,0.385 10 false G132 0.438,1.938 2.813,2.219 2.375,0.281 10 false No. 2 Junction Connector 2.115,2.594 3.469,2.979 1.354,0.385 10 false from Battery 1.844,3.417 3.198,3.802 1.354,0.385 10 false from ACC Relay 1.646,4.219 3,4.604 1.354,0.385 10 false from IG1 NO.1 Relay 3.792,4.063 5.146,4.448 1.354,0.385 10 false ECU-IG NO.2 4.115,3.25 5.469,3.635 1.354,0.385 10 false ACC 4.021,2.417 4.938,2.833 0.917,0.417 10 false RAD NO. 1 5.146,2.594 6.063,3.01 0.917,0.417 10 false H49 5.146,3.417 6.063,3.833 0.917,0.417 10 false H49 5.146,4.229 6.063,4.646 0.917,0.417 10 false H51 5.146,5.052 6.063,5.469 0.917,0.417 10 false H49 5.146,1.417 6.063,1.833 0.917,0.417 10 false H51 5.146,0.823 6.063,1.24 0.917,0.417 10 false H51 5.188,1.146 6.542,1.531 1.354,0.385 10 false 10 5.24,0.563 6.594,0.948 1.354,0.385 10 false 9 5.229,2.323 6.583,2.708 1.354,0.385 10 false 4 5.219,3.167 6.573,3.552 1.354,0.385 10 false 3 5.219,3.979 6.573,4.365 1.354,0.385 10 false 1 5.188,4.792 6.542,5.177 1.354,0.385 10 false 7

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


HINT:

Operating the ignition switch, any switches or any doors triggers related ECU and sensor communication with the CAN, which causes resistance variation.


PROCEDURE

1.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL
a.

Disconnect the cable from the negative (-) battery terminal before measuring the resistances of the CAN main wire and the CAN branch wire.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the airbag system.


NOTICE:
·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).

·

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).





NEXT

2.CHECK FOR OPEN IN CAN BUS WIRE (RADIO AND DISPLAY RECEIVER ASSEMBLY CAN BRANCH WIRE)
2.CHECK FOR OPEN IN CAN BUS WIRE (RADIO AND DISPLAY RECEIVER ASSEMBLY CAN BRANCH WIRE)
a.
U148880E01
0.082,0.083 0.286,0.253 0.205,0.170 10 *a 1.58,0.371 1.854,0.512 0.274,0.140 10 H51 2.039,1.299 2.26,1.774 2.26,1.774 2.366,1.774 false 1.908,1.299 1.687,1.774 1.687,1.774 1.581,1.774 false 1.079,1.699 1.490,1.837 0.411,0.139 10 CANH 2.398,1.699 2.809,1.837 0.411,0.139 10 CANL

Disconnect the H51 radio and display receiver assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
H51-9 (CANH) - H51-10 (CANL) Ignition switch off 54 to 69 Ω


Text in Illustration
*a Front view of wire harness connector
(to Radio and Display Receiver Assembly)



OK

3.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - BATTERY AND BODY GROUND)

NG

REPAIR OR REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY CAN BRANCH WIRE OR CONNECTOR (CANH, CANL)

3.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - BATTERY AND BODY GROUND)
a.
U148930E01
0.064,0.06 0.269,0.230 0.205,0.170 10 *a 2.01,0.866 2.297,0.554 2.297,0.554 2.402,0.554 false 2.184,0.98 2.383,1.19 2.383,1.19 2.488,1.19 false 1.599,1.152 1.351,1.459 1.351,1.459 1.246,1.459 false 0.449,2.359 0.613,2.498 0.165,0.139 10 IG 0.743,1.384 1.154,1.522 0.411,0.139 10 GND1 2.505,1.113 2.916,1.251 0.411,0.139 10 +B1 2.423,0.477 2.835,0.615 0.411,0.139 10 ACC1 0.651,2.432 0.786,2.432 0.786,2.432 0.981,2.605 false 1.577,1.826 1.857,1.963 0.279,0.137 10 H51 1.575,0.256 1.854,0.393 0.279,0.137 10 H49

Connect the cable to the negative (-) battery terminal.

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).



b.

Disconnect the H49 radio and display receiver assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H49-7 (GND1) - Body ground Always Below 1 Ω



d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
H49-4 (+B1) - Body ground Always 11 to 14 V
H49-3 (ACC1) - Body ground Ignition switch ACC 11 to 14 V
H51-1 (IG) - Body ground Ignition switch ON 11 to 14 V



Text in Illustration
*a Front view of wire harness connector
(to Radio and Display Receiver Assembly)


OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR