Home › Vehicle Interior › DOOR LOCK › POWER DOOR LOCK CONTROL SYSTEM › 2015.06–2017.08
RM27T0E _58 Vehicle Interior _053730 DOOR LOCK _0261036 POWER DOOR LOCK CONTROL SYSTEM C

DOOR LOCK  POWER DOOR LOCK CONTROL SYSTEM  B1243  GSW Terminal Circuit Malfunction  


DESCRIPTION

If the collision door lock release function does not operate normally, or an open or short in the GSW input circuit of the main body ECU (driver side junction block assembly) is detected, DTC B1243 is stored.

HINT:

If DTC B1243 is stored, the speed-sensitive automatic door lock function, shift-linked automatic door lock function and collision door lock release function are prohibited.


DTC Code DTC Detection Condition Trouble Area
B1243 Either condition is met:
·

An open or short in the GSW input circuit of the main body ECU (multiplex network body ECU).

·

The collision door lock release function does not operate normally.


·

Center airbag sensor assembly

·

Harness or connector

·

Main body ECU (multiplex network body ECU)



WIRING DIAGRAM

B243229E01
0.369,1.72 2.047,2.077 1.678,0.357 10 Main Body ECU (Multiplex Network Body ECU) 4.922,1.713 6.944,1.900 2.022,0.187 10 Center Airbag Sensor Assembly 0.369,1.533 0.877,1.712 0.508,0.179 10 A 4.922,1.533 5.430,1.712 0.508,0.179 10 G1 1.303,0.823 1.681,0.970 0.378,0.147 10 GSW 5.517,0.823 5.895,0.970 0.378,0.147 10 GSW 5.218,0.716 5.404,0.862 0.186,0.147 10 18 1.775,0.681 1.986,0.864 0.211,0.184 10 24

CAUTION / NOTICE / HINT

NOTICE:
·

w/ Navigation system:

After the ignition switch is turned off, the HDD navigation system requires approximately a minute to record various types of memory and settings. As a result, after turning the ignition switch off, wait a minute or more before disconnecting the cable from the negative (-) battery terminal.

·

When disconnecting the cable from the negative (-) battery terminal while performing repairs, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).



PROCEDURE

1.CHECK FOR DTC

b.

Check for DTCs (See page Vehicle Interior>DOOR LOCK>POWER DOOR LOCK CONTROL SYSTEM>DTC CHECK / CLEAR).

Result
Result Proceed to
DTC B1243 is output A
DTC B1243 is not output B



A

2.CHECK HARNESS AND CONNECTOR (MAIN BODY ECU - CENTER AIRBAG SENSOR)

B

2.CHECK HARNESS AND CONNECTOR (MAIN BODY ECU - CENTER AIRBAG SENSOR)
a.

Disconnect the cable from the negative (-) battery terminal.



c.

Disconnect the G1 center airbag sensor connector.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G1-18 (GSW) - A-24 (GSW) Always Below 1 Ω
G1-18 (GSW) - Body ground Always 10 kΩ or higher




OK

3.CHECK MAIN BODY ECU (GSW VOLTAGE)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK MAIN BODY ECU (GSW VOLTAGE)
a.
U115554E03
2.01,1.094 2.469,0.438 2.469,0.438 2.594,0.438 false 2.615,0.365 2.99,0.521 0.375,0.156 10 false GSW 0.354,1.083 0.563,1.24 0.208,0.156 10 false G1 0.177,0.104 0.344,0.25 0.167,0.146 10 false *a

Disconnect the cable from the negative (-) battery terminal.


b.

Disconnect the G1 center airbag sensor connector.


c.

Connect the cable to the negative (-) battery terminal.


d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
G1-18 (GSW) - Body ground Ignition switch ON 4.5 to 5.5 V


Text in Illustration
*a Front view of wire harness connector
(to Center Airbag Sensor)



OK

NG

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)