Home › Vehicle Interior › DOOR LOCK › POWER DOOR LOCK CONTROL SYSTEM › 2015.06–2017.08
RM27T0E _58 Vehicle Interior _053730 DOOR LOCK _0261036 POWER DOOR LOCK CONTROL SYSTEM J

DOOR LOCK  POWER DOOR LOCK CONTROL SYSTEM  All Doors LOCK/UNLOCK Functions do not Operate Via Master Switch, Driver Side Door Key Cylinder  


DESCRIPTION

The main body ECU (multiplex network body ECU) receives switch signals from the multiplex network master switch, and key-linked switch signals from the front door lock. The main body ECU (multiplex network body ECU) activates the door lock motor on each door according to these signals.

WIRING DIAGRAM

B449866E01
1.854,2.51 2.313,2.708 0.458,0.198 10 false UL3 1.906,3.063 2.365,3.26 0.458,0.198 10 false L2 2.25,2.927 2.708,3.125 0.458,0.198 10 false 11 4.531,1.865 5.24,2.115 0.708,0.25 10 false 8*2, 7*1 0.948,3.656 1.406,3.854 0.458,0.198 10 false G64 0.969,3.813 2.729,4.198 1.76,0.385 10 false Main Body ECU (Multiplex Network Body ECU) 0.688,5.417 2.51,5.573 1.823,0.156 10 false : LIN Communication Line 0.354,4.76 2.177,4.917 1.823,0.156 10 false *1: for LHD 0.354,5.063 2.177,5.219 1.823,0.156 10 false *2: for RHD 4.688,3.677 6.708,4.052 2.021,0.375 10 false Front Door Lock Assembly LH 4.698,4.177 6.719,4.552 2.021,0.375 10 false Front Door Lock Assembly RH 4.667,3.521 5.125,3.719 0.458,0.198 10 false K6*1 4.677,4.021 5.135,4.219 0.458,0.198 10 false J6*2 4.427,2.385 5.135,2.635 0.708,0.25 10 false 5*2, 10*1 5.094,2.396 5.552,2.594 0.458,0.198 10 false UL 5.115,2.958 5.573,3.156 0.458,0.198 10 false L 4.521,2.938 5.229,3.188 0.708,0.25 10 false 6*2, 9*1 5.125,1.854 5.583,2.052 0.458,0.198 10 false E 4.896,1.042 6.656,1.427 1.76,0.385 10 false Multiplex Network Master Switch Assembly 2.271,2.396 2.729,2.594 0.458,0.198 10 false 24

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


HINT:

Since the power door lock control system has functions that use LIN communication, first confirm that there is no malfunction in the communication system by inspecting the LIN communication functions in accordance with the "How to Proceed with Troubleshooting" procedures. Then, conduct the following inspection procedure.


PROCEDURE

1.CHECK DOOR LOCK OPERATION
a.

Check the door lock operation.

Result
Result Proceed to
No doors can be locked using multiplex network master switch A
No doors can be locked using key-linked switch B



A

REPLACE MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY

B

2.READ VALUE USING INTELLIGENT TESTER (KEY-LINKED SWITCH)
2.READ VALUE USING INTELLIGENT TESTER (KEY-LINKED SWITCH)
a.

Use the Data List to check if the door key-linked switches is functioning properly (See page Vehicle Interior>DOOR LOCK>POWER DOOR LOCK CONTROL SYSTEM>DATA LIST / ACTIVE TEST).

Main Body
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
Door Key SW-Lock Driver side door key-linked switch lock signal / ON or OFF ON: Driver side door key cylinder turned to lock position
OFF: Driver side door key cylinder not turned to lock position
-
D Door Key SW-UL Driver side door key-linked switch unlock signal / ON or OFF ON: Driver side door key cylinder turned to unlock position
OFF: Driver side door key cylinder not turned to unlock position
-

OK:

On tester screen, each item changes between ON and OFF according to above chart.




OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

NG

3.INSPECT FRONT DOOR LOCK ASSEMBLY (KEY-LINKED SWITCH)
3.INSPECT FRONT DOOR LOCK ASSEMBLY (KEY-LINKED SWITCH)
a.

Remove the front door lock (See page Vehicle Interior>DOOR LOCK>FRONT DOOR LOCK>REMOVAL).


b.

Measure the resistance according to the value(s) in the table below.

B245138E01
2.001,3.284 2.141,3.69 2.141,3.69 2.23,3.69 false 5.849,3.34 5.989,3.625 5.989,3.625 6.078,3.625 false 2.262,3.618 2.409,3.762 0.147,0.144 10 E 5.083,3.561 5.230,3.705 0.147,0.144 10 E 1.497,3.163 1.351,2.999 1.351,2.999 1.259,2.999 false 1.319,3.558 1.426,3.702 0.107,0.144 10 L 5.522,3.558 5.629,3.702 0.107,0.144 10 L 1.053,2.946 1.252,3.090 0.200,0.144 10 UL 6.121,3.598 6.321,3.742 0.200,0.144 10 UL 0.32,0.262 0.517,0.404 0.198,0.142 10 *A 3.907,0.262 4.104,0.404 0.198,0.142 10 *B 1.665,3.289 1.475,3.639 1.475,3.639 1.417,3.639 false 5.681,3.345 5.62,3.62 5.62,3.62 5.602,3.62 false 5.382,3.345 5.264,3.639 5.264,3.639 5.228,3.639 false 2.956,1.344 3.172,1.513 0.216,0.170 10 *a 4.329,1.063 4.545,1.233 0.216,0.170 10 *a

Text in Illustration
*A for LHD *B for RHD
*a Off - -
V100135

Lock
V100136

Unlock

Standard Resistance:
for LHD:
Tester Connection Condition Specified Condition
9 (L) - 7 (E) Lock Below 1 Ω
9 (L) - 7 (E) Off 10 kΩ or higher
10 (UL) - 7 (E) Unlock Below 1 Ω
10 (UL) - 7 (E) Off 10 kΩ or higher

for RHD:
Tester Connection Condition Specified Condition
6 (L) - 8 (E) Lock Below 1 Ω
6 (L) - 8 (E) Off 10 kΩ or higher
5 (UL) - 8 (E) Unlock Below 1 Ω
5 (UL) - 8 (E) Off 10 kΩ or higher




OK

4.CHECK HARNESS AND CONNECTOR (FRONT DOOR LOCK ASSEMBLY - MAIN BODY ECU AND BODY GROUND)

NG

REPLACE FRONT DOOR LOCK ASSEMBLY

4.CHECK HARNESS AND CONNECTOR (FRONT DOOR LOCK ASSEMBLY - MAIN BODY ECU AND BODY GROUND)
a.

Disconnect the K6*1 and J6*2 door lock connectors.

*1: for LHD

*2: for RHD



b.

Remove the G46 main body ECU (See page Power Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>REMOVAL).


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for LHD:
Tester Connection Condition Specified Condition
K6-10 (UL) - G64-24 (UL3) Always Below 1 Ω
K6-9 (L) - G64-11 (L2) Always Below 1 Ω
K6-7 (E) - Body ground Always Below 1 Ω
K6-10 (UL) - Body ground Always 10 kΩ or higher
K6-9 (L) - Body ground Always 10 kΩ or higher

for RHD:
Tester Connection Condition Specified Condition
J6-5 (UL) - G64-24 (UL3) Always Below 1 Ω
J6-6 (L) - G64-11 (L2) Always Below 1 Ω
J6-8 (E) - Body ground Always Below 1 Ω
J6-5 (UL) - Body ground Always 10 kΩ or higher
J6-6 (L) - Body ground Always 10 kΩ or higher




OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR