Home › Vehicle Interior › DOOR LOCK › KEY REMINDER WARNING SYSTEM › 2015.06–2017.08
RM27T0E _58 Vehicle Interior _053730 DOOR LOCK _0261037 KEY REMINDER WARNING SYSTEM J

DOOR LOCK  KEY REMINDER WARNING SYSTEM  Key Reminder Buzzer does not Sound  


DESCRIPTION

The key reminder warning buzzer sounds when the driver side door is opened while the ignition switch is ACC or off and the key is in the ignition key cylinder. The key reminder warning buzzer is activated when the main body ECU sends an unlock warning switch signal and front door courtesy light switch LH*1 or RH*2 signal to the combination meter.

*1: for LHD

*2: for RHD


WIRING DIAGRAM

B449872E01
1.469,0.948 6.052,1.146 4.583,0.198 10 false G3 1.479,1.135 6.063,1.333 4.583,0.198 10 false Unlock Warning Switch Assembly 1.625,0.49 1.99,0.688 0.365,0.198 10 false UN- 2.635,0.479 3,0.677 0.365,0.198 10 false UN+ 1.385,0.479 1.75,0.677 0.365,0.198 10 false 2 3.021,0.469 3.385,0.667 0.365,0.198 10 false 1 3.833,0.594 4.198,0.792 0.365,0.198 10 false G64 3.885,0.385 4.25,0.583 0.365,0.198 10 false 17 4.177,0.594 4.594,0.823 0.417,0.229 10 false KSW 3.906,2.198 4.323,2.427 0.417,0.229 10 false A 3.552,2.198 3.969,2.427 0.417,0.229 10 false A 3.479,2 3.844,2.198 0.365,0.198 10 false 4*2 3.854,2 4.219,2.198 0.365,0.198 10 false 2*1 4.156,2.198 4.781,2.438 0.625,0.24 10 false FLCY*1 1.354,2.74 3.344,3.24 1.99,0.5 10 false Front Door Courtesy Light Switch Assembly LH*1, RH*2 1.365,2.563 5.948,2.76 4.583,0.198 10 false R7*1, Q8*2 0.667,4.302 5.25,4.5 4.583,0.198 10 false : CAN Communication Line 3,2.063 3.365,2.26 0.365,0.198 10 false 1 4.156,2.385 4.781,2.625 0.625,0.24 10 false FRCY*2 3.865,2.865 5.854,3.365 1.99,0.5 10 false Main Body ECU (Multiplex Network Body ECU) 5.75,2.323 7.156,2.875 1.406,0.552 10 false Combination Meter Assembly 0.24,3.479 4.823,3.677 4.583,0.198 10 false *1: for LHD 0.24,3.771 4.823,3.969 4.583,0.198 10 false *2: for RHD

CAUTION / NOTICE / HINT

HINT:

Since the key reminder warning system has functions that use CAN communication, first confirm that there is no malfunction in the communication system by inspecting CAN communication in accordance with the "How to Proceed with Troubleshooting" procedures. Then, conduct the following inspection procedure.


PROCEDURE

1.READ VALUE USING INTELLIGENT TESTER (FRONT DOOR COURTESY LIGHT SWITCH)
a.

Check the Data List for proper functioning of the front door courtesy light switch (See page Vehicle Interior>DOOR LOCK>KEY REMINDER WARNING SYSTEM>DATA LIST / ACTIVE TEST).

i.

for LHD:

Main Body
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
FL Door Courtesy Front door courtesy light switch LH signal / ON or OFF ON: Front door LH closed
OFF: Front door LH open
-


ii.

for RHD:

Main Body
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
FR Door Courtesy Front door courtesy light switch RH signal / ON or OFF ON: Front door RH closed
OFF: Front door RH open
-

OK:

On tester screen, each item changes between ON and OFF according to above chart.





OK

2.READ VALUE USING INTELLIGENT TESTER (UNLOCK WARNING SWITCH)

NG

2.READ VALUE USING INTELLIGENT TESTER (UNLOCK WARNING SWITCH)
a.

Check the Data List for proper functioning of the unlock warning switch (See page Vehicle Interior>DOOR LOCK>KEY REMINDER WARNING SYSTEM>DATA LIST / ACTIVE TEST).

Main Body
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
Key Unlock Warning SW Unlock warning switch signal / ON or OFF ON: Key in ignition key cylinder
OFF: No key in ignition key cylinder
-

OK:

On tester screen, each item changes between ON and OFF according to above chart.




OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

NG

3.INSPECT UNLOCK WARNING SWITCH ASSEMBLY
3.INSPECT UNLOCK WARNING SWITCH ASSEMBLY
a.
E198930E02
2.567,1.406 2.875,1.562 0.309,0.156 10 UN+ 0.633,1.393 0.942,1.549 0.309,0.156 10 UN- 1.948,1.33 2.524,1.476 false 1.62,1.333 0.974,1.476 false

Remove the unlock warning switch (See page Vehicle Interior>DOOR LOCK>UNLOCK WARNING SWITCH>REMOVAL).


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
1 (UN+) - 2 (UN-) Not pushed 10 kΩ or higher
Pushed Below 1 Ω




OK

4.CHECK HARNESS AND CONNECTOR (UNLOCK WARNING SWITCH ASSEMBLY - MAIN BODY ECU AND BODY GROUND)

NG

REPLACE UNLOCK WARNING SWITCH ASSEMBLY

4.CHECK HARNESS AND CONNECTOR (UNLOCK WARNING SWITCH ASSEMBLY - MAIN BODY ECU AND BODY GROUND)
a.

Disconnect the G3 unlock warning switch connector.


b.

Disconnect the G64 main body ECU connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G3-1 (UN+) - G64-17 (KSW) Always Below 1 Ω
G3-2 (UN-) - Body ground Always Below 1 Ω
G64-17 (KSW) - Body ground Always 10 kΩ or higher




OK

5.CHECK COMBINATION METER ASSEMBLY (OPERATION)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK COMBINATION METER ASSEMBLY (OPERATION)
a.

Temporarily replace the combination meter assembly with a new or normally functioning one (See page Vehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>OPERATION CHECK).


b.

Check the key reminder warning system (See page Vehicle Interior>DOOR LOCK>KEY REMINDER WARNING SYSTEM>OPERATION CHECK).

OK:

The key reminder warning system functions properly.




OK

END (COMBINATION METER IS DEFECTIVE)

NG

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)