Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › ENTRY AND START SYSTEM (for Start Function) › 2015.06–2017.08
RM27T0E _58 Vehicle Interior _053731 THEFT DETERRENT / KEYLESS ENTRY _0261052 ENTRY AND START SYSTEM(for Start Function) C

THEFT DETERRENT / KEYLESS ENTRY  ENTRY AND START SYSTEM(for Start Function)  B2271  Ignition Hold Monitor Malfunction  


DESCRIPTION

This DTC is stored when a problem, such as an open in the AM2 fuse, an open or short in the wire harness between the fuse and power management control ECU, a short in the IG output circuit inside the power management control ECU, a short between the power management control ECU and relay, or a short in the relay, is detected.

HINT:

When the power management control ECU is replaced with a new one and the cable is connected to the negative (-) battery terminal, the power source mode is reset to on (IG). When the battery is removed and reinstalled, the power source mode that was selected when the battery was removed is restored.


DTC Code DTC Detection Condition Trouble Area
B2271 The hold circuit, IG1 relay actuation circuit or IG2 relay actuation circuit inside the power management control ECU is open or shorted.
·

AM2 fuse

·

Main body ECU (Driver side junction block assembly) (IG1 relays)

·

No. 1 integration relay (IG2 relay)

·

Power management control ECU

·

Harness or connector



WIRING DIAGRAM

C217202E15
2.656,4.021 3.938,4.375 1.281,0.354 10 false Power Management Control ECU 2.563,3.167 2.906,3.323 0.344,0.156 10 false G51 2.542,1.823 2.865,1.99 0.323,0.167 10 false G50 2.646,1.615 2.771,1.792 0.125,0.177 10 false 8 2.281,1.552 2.49,1.906 0.208,0.354 10 false 1*1 6*2 0.552,1.719 0.667,1.885 0.115,0.167 10 false 3 3.802,1.823 4.094,1.979 0.292,0.156 10 false G51 3.865,1.635 4.042,1.802 0.177,0.167 10 false 20 4.479,1.833 4.719,1.979 0.24,0.146 10 false 2A 5.25,1.156 5.896,1.323 0.646,0.167 10 false IG1 NO. 1 5.229,2.104 5.896,2.271 0.667,0.167 10 false IG1 NO. 2 5.26,3.063 5.896,3.219 0.635,0.156 10 false IG1 NO. 3 4.427,3.448 6.844,3.656 2.417,0.208 10 false Driver Side Junction Block Assembly 0.698,2.677 2.323,3.104 1.625,0.427 10 false Engine Room Relay Block (No. 1 Integration Relay) 1.333,2.104 1.583,2.25 0.25,0.146 10 false IG2 4.49,1.635 4.677,1.844 0.188,0.208 10 false 52 6.448,1.833 6.708,1.979 0.26,0.146 10 false 2D 6.49,1.635 6.604,1.781 0.115,0.146 10 false 4 2.646,0.844 2.833,1.073 0.188,0.229 10 false 1 2.646,0.427 2.75,0.594 0.104,0.167 10 false 2 2.552,3.573 2.833,3.74 0.281,0.167 10 false G51 2.646,3.385 2.75,3.542 0.104,0.156 10 false 6 2.667,2.979 2.781,3.135 0.115,0.156 10 false 5 2.906,3.208 3.323,3.385 0.417,0.177 10 false GND2 2.906,1.844 3.25,2.021 0.344,0.177 10 false IG2D 3.385,1.844 3.719,2.021 0.333,0.177 10 false IG1D 2.552,1.021 2.906,1.177 0.354,0.156 10 false G51 2.542,0.635 2.844,0.792 0.302,0.156 10 false G51 2.906,1.042 3.302,1.208 0.396,0.167 10 false AM22 2.906,0.635 3.302,0.792 0.396,0.156 10 false AM21 1.542,0.771 1.854,0.938 0.313,0.167 10 false AM2 0.292,0.656 1.156,0.969 0.865,0.313 10 false from Battery 2.906,3.563 3.229,3.729 0.323,0.167 10 false GND 0.708,2.521 1.854,2.781 1.146,0.26 10 false 1A*1, 1J*2 4.063,3.938 6.938,4.208 2.875,0.271 10 false *1: except 1GD-FTV (w/ Urea SCR System) 4.052,4.219 6.927,4.49 2.875,0.271 10 false *2: for 1GD-FTV (w/ Urea SCR System)

CAUTION / NOTICE / HINT

NOTICE:
·

When using the intelligent tester with the engine switch off to troubleshoot: Connect the intelligent tester to the vehicle and turn a courtesy light switch on and off at 1.5 second intervals until communication between the intelligent tester and vehicle begins.

·

Before performing the inspection, check that there are no problems related to the CAN communication system and LIN communication system.

·

Inspect the fuses for circuits related to this system before performing the following inspection procedure.



PROCEDURE

1.CHECK HARNESS AND CONNECTOR (BATTERY - POWER MANAGEMENT CONTROL ECU)
a.
U169135E02
2.958,1.417 2.906,1.417 2.906,1.417 2.813,2.073 false 2.719,2.094 2.604,1.333 2.604,1.333 2.521,1.333 false 0.083,0.052 0.24,0.229 0.156,0.177 10 false *a 2.99,1.302 3.406,1.5 0.417,0.198 10 false AM22 2.115,1.229 2.531,1.417 0.417,0.188 10 false AM21 0.729,1.969 1.052,2.146 0.323,0.177 10 false G51

Disconnect the G51 power management control ECU connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
G51-2 (AM21) - Body ground Always 9.5 to 14 V
G51-1 (AM22) - Body ground


Text in Illustration
*a Rear view of wire harness connector
(to Power Management Control ECU)



OK

2.CHECK HARNESS AND CONNECTOR (POWER MANAGEMENT CONTROL ECU - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.CHECK HARNESS AND CONNECTOR (POWER MANAGEMENT CONTROL ECU - BODY GROUND)
a.

Disconnect the G51 power management control ECU connector.


b.
U169136E02
1.073,2.458 1.125,2.458 1.125,2.458 1.521,2.094 false 1.208,2.719 1.26,2.719 1.26,2.719 1.604,2.115 false 0.104,0.063 0.26,0.24 0.156,0.177 10 false *a 0.75,2.625 1.177,2.771 0.427,0.146 10 false GND2 0.698,2.375 1.052,2.521 0.354,0.146 10 false GND 0.74,1.74 1.063,1.917 0.323,0.177 10 false G51

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G51-6 (GND) - Body ground Always Below 1 Ω
G51-5 (GND2) - Body ground


Text in Illustration
*a Rear view of wire harness connector
(to Power Management Control ECU)



OK

3.INSPECT NO. 1 INTEGRATION RELAY (IG2 RELAY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.INSPECT NO. 1 INTEGRATION RELAY (IG2 RELAY)
a.

Remove the No. 1 integration relay.


b.

Measure the resistance according to the value(s) in the table below.

U170500E02
2.198,0.24 2.51,0.479 0.313,0.24 10 false 1J 4.917,2.135 5.229,2.271 0.313,0.135 10 false 1A 0.938,1.948 1.198,2.156 0.26,0.208 10 false *B 0.896,0.063 1.156,0.271 0.26,0.208 10 false *A 0.125,0.021 0.385,0.229 0.26,0.208 10 false *a

Text in Illustration
*A for 1GD-FTV (w/ Urea SCR System) *B except 1GD-FTV (w/ Urea SCR System)
*a Component without harness connected
(No. 1 Integration Relay)
- -

Standard Resistance:
for 1GD-FTV (w/ Urea SCR System):
Tester Connection Condition Specified Condition
1J-6 - 1J-3 20°C (68°F) 500 to 750Ω

except 1GD-FTV (w/ Urea SCR System):
Tester Connection Condition Specified Condition
1A-1 - 1A-3 20°C (68°F) 255 to 387 Ω




OK

4.INSPECT DRIVER SIDE JUNCTION BLOCK ASSEMBLY (IG1 NO. 1, IG1 NO. 2 AND IG1 NO. 3 RELAYS)

NG

REPLACE NO. 1 INTEGRATION RELAY

4.INSPECT DRIVER SIDE JUNCTION BLOCK ASSEMBLY (IG1 NO. 1, IG1 NO. 2 AND IG1 NO. 3 RELAYS)
a.
U169669E01
2.178,2.664 2.389,2.826 0.211,0.163 10 2A 2.178,1.511 2.389,1.674 0.211,0.163 10 2D 2.413,3.113 2.871,3.275 0.458,0.163 10 2A-52 0.7,1.44 1.075,1.603 0.375,0.163 10 2D-4 0.257,0.136 0.469,0.299 0.211,0.163 10 *a 1.774,3.195 2.366,3.195 false 1.63,1.524 1.107,1.524 false

Remove the driver side junction block assembly.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
2A-52 - 2D-4 20°C (68°F) 101.25 to 123.75 Ω


Text in Illustration
*a Component without harness connected
(Driver Side Junction Block Assembly)



OK

5.CHECK HARNESS AND CONNECTOR (POWER MANAGEMENT CONTROL ECU - DRIVER SIDE JUNCTION BLOCK ASSEMBLY)

NG

REPLACE MAIN BODY ECU (DRIVER SIDE JUNCTION BLOCK ASSEMBLY)

5.CHECK HARNESS AND CONNECTOR (POWER MANAGEMENT CONTROL ECU - DRIVER SIDE JUNCTION BLOCK ASSEMBLY)
a.

Disconnect the G51 power management control ECU connector.


b.

Disconnect the 2A driver side junction block assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G51-20 (IG1D) - 2A-52 Always Below 1 Ω
G51-20 (IG1D) - Body ground Always 10 kΩ or higher




OK

6.CHECK HARNESS AND CONNECTOR (DRIVER SIDE JUNCTION BLOCK ASSEMBLY - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.CHECK HARNESS AND CONNECTOR (DRIVER SIDE JUNCTION BLOCK ASSEMBLY - BODY GROUND)
a.

Disconnect the 2D driver side junction block assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
2D-4 - Body ground Always Below 1 Ω




OK

7.CHECK HARNESS AND CONNECTOR (POWER MANAGEMENT CONTROL ECU - NO. 1 INTEGRATION RELAY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.CHECK HARNESS AND CONNECTOR (POWER MANAGEMENT CONTROL ECU - NO. 1 INTEGRATION RELAY)
a.

Disconnect the G50 power management control ECU connector.


b.

Disconnect the 1J*1 or 1A*2 No. 1 integration relay connector.

*1: for 1GD-FTV (w/ Urea SCR System)

*2: except 1GD-FTV (w/ Urea SCR System)



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for 1GD-FTV (w/ Urea SCR System):
Tester Connection Condition Specified Condition
G50-8 (IG2D) - 1J-6 Always Below 1 Ω
G50-8 (IG2D) - Body ground Always 10 kΩ or higher

except 1GD-FTV (w/ Urea SCR System):
Tester Connection Condition Specified Condition
G50-8 (IG2D) - 1A-1 Always Below 1 Ω
G50-8 (IG2D) - Body ground Always 10 kΩ or higher




OK

8.CHECK HARNESS AND CONNECTOR (NO. 1 INTEGRATION RELAY - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

8.CHECK HARNESS AND CONNECTOR (NO. 1 INTEGRATION RELAY - BODY GROUND)
a.

Disconnect the 1J*1 or 1A*2 No. 1 integration relay connector.

*1: for 1GD-FTV (w/ Urea SCR System)

*2: except 1GD-FTV (w/ Urea SCR System)



b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for 1GD-FTV (w/ Urea SCR System):
Tester Connection Condition Specified Condition
1J-3 - Body ground Always Below 1 Ω

except 1GD-FTV (w/ Urea SCR System):
Tester Connection Condition Specified Condition
1A-3 - Body ground Always Below 1 Ω




OK

9.CHECK POWER MANAGEMENT CONTROL ECU

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

9.CHECK POWER MANAGEMENT CONTROL ECU
a.

Install the No. 1 integration relay.


b.

Install the driver side junction block assembly.


c.

Connect the power management control ECU connectors.

U169906E01
0.135,0.091 0.337,0.251 0.202,0.160 10 *a 3.475,0.566 3.816,0.737 0.341,0.172 10 IG2D 5.707,0.615 6.144,0.787 0.437,0.172 10 IG1D 3.438,0.647 3.363,0.647 3.363,0.647 3.233,1.451 false 5.305,1.637 5.564,0.677 5.564,0.677 5.676,0.677 false 4.49,0.69 4.773,0.862 0.283,0.172 10 G51 2.425,0.69 2.708,0.862 0.283,0.172 10 G50

Text in Illustration
*a Component with harness connected
(Power Management Control ECU)
- -


d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
G50-8 (IG2D) - Body ground Engine switch off Below 1 V
Engine switch on (IG) ((Voltage at terminal AM21 or AM22) minus 2.0 V) or higher
G51-20 (IG1D) - Body ground Engine switch off Below 1 V
Engine switch on (IG) ((Voltage at terminal AM21 or AM22) minus 2.0 V) or higher




OK

NG