If the front passenger side door entry unlock function does not operate but the entry lock function operates, the communication line between the vehicle and electrical key transmitter is normal. The part at fault may be an unlock sensor circuit (front door outside handle assembly [for front passenger side] → certification ECU).
The entry and start system (for Entry Function) uses a multiplex communication system (LIN communication system) and the CAN communication system. Inspect the communication function by following How to Proceed with Troubleshooting (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM (for Entry Function)>HOW TO PROCEED WITH TROUBLESHOOTING). Troubleshoot the entry and start system (for Entry Function) after confirming that the communication systems are functioning properly.
When using the intelligent tester with the engine switch off to troubleshoot: Connect the intelligent tester to the DLC3 and turn a courtesy light switch on and off at 1.5-second intervals until communication between the intelligent tester and vehicle begins.
Check that there are no electrical key transmitters in the vehicle.
Before performing the inspection, check that DTC B1242 (wireless door lock control) is not output (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM (for Entry Function)>DTC CHECK / CLEAR).
When checking the entry lock operation multiple times, the lock operation may be limited to 2 consecutive operations depending on the settings. In order to perform the entry lock operation 3 or more times, an unlock operation must be performed once (any type of unlock operation is sufficient). However, only consecutive entry lock operations are limited. Using the wireless lock or other types of lock operations, it is possible to perform consecutive lock operations without this limitation.
Before replacing the certification ECU, refer to the Service Bulletin.
When the door control switch on the multiplex network master switch assembly is operated, check that the doors unlock and lock according to the switch operation (See page Vehicle Interior>DOOR LOCK>POWER DOOR LOCK CONTROL SYSTEM>OPERATION CHECK).
Door locks operate normally.
OK
NG
(See pageVehicle Interior>DOOR LOCK>POWER DOOR LOCK CONTROL SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING)
Connect the intelligent tester to the DLC3.
Turn the engine switch on (IG).
Turn the intelligent tester on.
Enter the following menus: Body / Main Body / Data List.
Read the Data List according to the display on the intelligent tester.
| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
|---|---|---|---|
| FR Door Lock Pos*1 | Front RH side door lock position switch signal / UNLOCK or LOCK | UNLOCK: Front RH side door unlocked
LOCK: Front RH side door locked |
- |
| FL Door Lock Pos*2 | Front LH side door lock position switch signal / UNLOCK or LOCK | UNLOCK: Front LH side door unlocked
LOCK: Front LH side door locked |
- |
*1: for LHD
*2: for RHD
On the intelligent tester screen, the display changes between LOCK and UNLOCK as shown in the chart above.
OK
NG
Using the intelligent tester, read the Data List (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM (for Entry Function)>DATA LIST / ACTIVE TEST).
| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
|---|---|---|---|
| P-Door Touch Sensor | Front passenger side door unlock sensor / ON or OFF | ON: Front passenger side door unlock sensor touched
OFF: Front passenger side door unlock sensor not touched |
- |
"ON" (unlock sensor is touched) and "OFF" (unlock sensor is not touched) appear on the screen.
OK
NG
Disconnect the N1*1 or O1*2 handle connector.
*1: for LHD
*2: for RHD
Disconnect the G38 ECU connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| N1-4 (SENS) - G38-21 (SEN2) | Always | Below 1 Ω |
| G38-21 (SEN2) - Body ground | Always | 10 kΩ or higher |
| G38-15 (E) - Body ground | Always | Below 1 Ω |
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| O1-4 (SENS) - G38-21 (SEN2) | Always | Below 1 Ω |
| G38-21 (SEN2) - Body ground | Always | 10 kΩ or higher |
| G38-15 (E) - Body ground | Always | Below 1 Ω |
OK
NG
Measure the voltage according to the value(s) in the table below.
| *a | Component with harness connected
(Certification ECU) |
- | - |
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| G38-21 (SEN2) - G38-15 (E) | Engine switch off, all doors locked, key not sufficiently close to vehicle and unlock sensor (for front passenger side) off → on | Pulse generation → Below 2 V |
OK
NG