Home › Vehicle Exterior › DOOR / HATCH › FRONT DOOR › 2015.06–2017.08
RM27T0E _59 Vehicle Exterior _053744 DOOR / HATCH _0261247 FRONT DOOR A

DOOR / HATCH  FRONT DOOR  DISASSEMBLY  


CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for RHD and LHD vehicles.

·

The procedure listed below is for LHD vehicles.

·

Use the same procedure for the RH and LH sides.

·

The procedure listed below is for the LH side.



PROCEDURE

Hide 1.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.


NOTICE:
·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).

·

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).



Hide 67492A 2.REMOVE FRONT DOOR LOWER FRAME BRACKET GARNISH LH

a.
B240614

Detach the 2 clips and remove the front door lower frame bracket garnish LH.


Hide 69298A 3.REMOVE NO. 2 DOOR INSIDE HANDLE BEZEL LH

a.
B238520

Using a moulding remover, detach the 3 claws and remove the inside handle bezel as shown in the illustration.


Hide 74611C 4.REMOVE ASSIST GRIP COVER LH

a.
B238521

Using moulding remover A, detach the 8 claws and remove the assist grip cover.


Hide 67602 5.REMOVE FRONT DOOR TRIM BOARD SUB-ASSEMBLY LH

a.
B238522

Remove the 3 screws.


b.

Remove the 12 clips.


c.
B238523E01
1.601,3.239 1.866,3.447 0.265,0.208 10 *1 1.554,3.333 1.188,3.333 1.188,3.333 1.011,3.672 false

Pull out the front door trim board sub-assembly in the direction indicated by the arrow in the illustration.

Text in Illustration
*1 Reference Boss


d.

Raise the front door trim board sub-assembly to detach the 4 claws and remove the front door trim board sub-assembly together with the front door inner glass weatherstrip LH.


e.
B238524

Disconnect the 2 connectors.


f.

w/ Seat Position Memory System:

i.
B240206

Disconnect the connectors.



g.
B238525

Disconnect the front door lock remote control cable assembly and front door inside locking cable assembly.


Hide 68172A 6.REMOVE FRONT DOOR INNER GLASS WEATHERSTRIP LH

a.
B238526

Using a screwdriver, detach the 4 claws and remove the front door inner glass weatherstrip from the front door trim board sub-assembly as shown in the illustration.


Hide 81910A 7.REMOVE FRONT REFLEX REFLECTOR ASSEMBLY

a.
E198063

Detach the 2 claws and remove the front reflex reflector assembly.


Hide 81080E 8.REMOVE FRONT DOOR INSIDE HANDLE ILLUMINATION LIGHT ASSEMBLY LH

Hide 81081A 9.REMOVE NO. 2 INTERIOR ILLUMINATION LIGHT SUB-ASSEMBLY

Hide 84927 10.REMOVE SEAT MEMORY SWITCH (w/ Seat Position Memory System)

Hide 84040 11.REMOVE MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY (for Driver Side)

a.
B238528

Remove the 3 screws and the multiplex network master switch assembly.


Hide 84810 12.REMOVE POWER WINDOW REGULATOR SWITCH ASSEMBLY (for Front Passenger Side)

Hide 69206B 13.REMOVE FRONT DOOR INSIDE HANDLE SUB-ASSEMBLY LH

a.
B238529

Remove the 8 screws and door assist grip assembly LH.


b.
B238527

Remove the 2 screws.


c.

Detach the guide and 2 claws and remove the front door inside handle sub-assembly from the front door trim board sub-assembly.


Hide 86160 14.REMOVE FRONT NO. 1 SPEAKER ASSEMBLY

Hide 89860A 15.REMOVE SIDE AIRBAG SENSOR ASSEMBLY LH

Hide 67832 16.REMOVE FRONT DOOR SERVICE HOLE COVER LH

a.
B238530

Remove the bolt.


b.

Detach the 2 clamps, move the wire harness out of the way and remove the service hole cover.

HINT:

Remove any remaining butyl tape from the door.



Hide 87940 17.REMOVE OUTER REAR VIEW MIRROR ASSEMBLY LH

Hide 68102 18.REMOVE FRONT DOOR GLASS SUB-ASSEMBLY LH

a.

Connect the cable to the negative (-) battery terminal.


b.

Connect the power window regulator master switch assembly and move the front door glass sub-assembly so that the door glass bolts can be seen.


c.

Disconnect the cable from the negative (-) battery terminal and power window regulator master switch assembly.

NOTICE:
·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).

·

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).




d.
B238531

Remove the 2 bolts.

NOTICE:

After the bolts are removed, do not allow the door glass to fall.



e.
B238532E05
0.365,0.427 0.635,0.656 0.271,0.229 10 true (1) 2.469,0.188 2.698,0.406 0.229,0.219 10 true (2)

Remove the front door glass sub-assembly as indicated by the arrows in the order shown in the illustration.

NOTICE:

Do not damage the door glass.



Hide 69802 19.REMOVE FRONT DOOR WINDOW REGULATOR SUB-ASSEMBLY LH

a.
B238533E10
2.094,1.302 1.885,1.302 true 1.677,1.229 1.979,1.469 0.302,0.24 10 true *1

Disconnect the connector.


b.

Loosen the temporary bolt.

Text in Illustration
*1 Temporary Bolt

NOTICE:

Do not remove the temporary bolt. If the temporary bolt is removed, the front door window regulator may fall and cause damage.



c.

Remove the 5 bolts.


d.

Remove the front door window regulator sub-assembly.


e.

Remove the temporary bolt from the front door window regulator sub-assembly.


Hide 85720C 20.REMOVE FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY LH

Hide 68151D 21.REMOVE FRONT DOOR GLASS RUN LH

a.
B238535

Remove the front door glass run.


Hide 67674A 22.REMOVE REAR DOOR FRAME GARNISH LH

a.
B238558

Detach the clip and remove the door frame garnish.


Hide 67404F 23.REMOVE FRONT DOOR REAR LOWER FRAME SUB-ASSEMBLY LH

a.
B238536

Remove the bolt and front door rear lower frame sub-assembly as shown in the illustration.


Hide 24.REMOVE FRONT DOOR OUTSIDE HANDLE COVER WITH LOCK CYLINDER ASSEMBLY (for Driver Side)

a.
B238537

Remove the hole plug.


b.
B238538

Using a T30 "TORX" socket wrench, loosen the screw and remove the front door outside handle cover with lock cylinder assembly.

HINT:

The screw cannot be removed because it is integrated into the front door outside handle frame sub-assembly.



Hide 69217F 25.REMOVE FRONT DOOR OUTSIDE HANDLE COVER LH (for Driver Side)

a.
B238539

Using a screwdriver, detach the claw and remove the front door outside handle cover.


Hide 69217E 26.REMOVE FRONT DOOR OUTSIDE HANDLE COVER RH (for Front Passenger Side)

a.
B241166

Remove the hole plug.


b.
B238540

Using a T30 "TORX" socket wrench, loosen the screw and remove the front door outside handle cover.

HINT:

The screw cannot be removed because it is integrated into the front door outside handle frame sub-assembly.



Hide 69220 27.REMOVE FRONT DOOR OUTSIDE HANDLE ASSEMBLY LH

a.

w/ Entry and Start System:

i.
B238541

Detach the 2 claws.


ii.

Disconnect the connector.



b.
B238542

Move the lever in the direction indicated by the arrow in the illustration.


c.
B238543

Remove the front door outside handle assembly as shown in the illustration.


Hide 69252 28.REMOVE FRONT DOOR FRONT OUTSIDE HANDLE PAD LH

a.
B238544

Detach the 3 claws and remove the front door front outside handle pad.


Hide 69254C 29.REMOVE FRONT DOOR REAR OUTSIDE HANDLE PAD LH

a.
B238545

Detach the 2 claws and remove the front door rear outside handle pad.


Hide 69040A 30.REMOVE FRONT DOOR LOCK ASSEMBLY LH

Hide 69720B 31.REMOVE FRONT DOOR LOCK REMOTE CONTROL CABLE ASSEMBLY LH

a.
B238548

Remove the front door lock remote control cable assembly.


Hide 69760C 32.REMOVE FRONT DOOR INSIDE LOCKING CABLE ASSEMBLY LH

a.
B238549

Using a screwdriver, detach the 3 claws.

HINT:

Tape the screwdriver tip before use.



b.
B238550

Remove the front door inside locking cable assembly.


Hide 69202A 33.REMOVE FRONT DOOR OUTSIDE HANDLE FRAME SUB-ASSEMBLY LH

a.

w/ Entry and Start System:

i.
B238551

Disconnect the connector.


ii.

Detach the clamp and remove the front door No. 2 wire.



b.
B238553

Using a T30 "TORX" socket wrench, loosen the screw.


c.

Slide the front door outside handle frame sub-assembly to detach the door handle nut and claw of the front door outside handle frame sub-assembly, and then remove the front door outside handle frame sub-assembly.


Hide 82152A 34.REMOVE FRONT DOOR NO. 2 WIRE LH (w/ Entry and Start System)

a.
B238552

Detach the 4 clamps and remove the front door No. 2 wire.


Hide 69312 35.REMOVE FRONT DOOR LOCK OPEN ROD LH

a.
B238554E05
2.917,2.5 3.167,2.75 0.25,0.25 10 true (2) 2.479,1.917 2.75,2.135 0.271,0.219 10 true (1)

Remove the front door lock open rod as indicated by the arrows, in the order shown in the illustration.


Hide 67924 36.REMOVE FRONT DOOR NO. 2 STIFFENER CUSHION

a.
B238555E05
2.417,1.167 2.083,1.167 2.083,1.167 1.667,0.667 true 2.458,1.083 2.667,1.281 0.208,0.198 10 false *1

Remove the 2 bolts.

Text in Illustration
*1 Double-sided Tape


b.

Detach the 2 claws and remove the front door No. 2 stiffener cushion.


Hide 68620 37.REMOVE FRONT DOOR CHECK ASSEMBLY LH

a.
B238556

Remove the bolt, 2 nuts and front door check assembly.


Hide 67862 38.REMOVE FRONT DOOR WEATHERSTRIP LH

a.
B238557

Using a clip remover, detach the 21 clips and remove the front door weatherstrip.


Hide 75756C 40.REMOVE FRONT DOOR REAR WINDOW FRAME MOULDING LH

Hide 75976G 43.REMOVE LOWER FRONT DOOR OUTSIDE STRIPE LH

Hide 67001A 44.REMOVE FRONT DOOR PANEL CUSHION

a.
B240615

Using a clip remover, detach the clip and remove the door panel cushion.