Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › ENTRY AND START SYSTEM (for Entry Function) › 2015.06–2017.08
RM27T0E _58 Vehicle Interior _053731 THEFT DETERRENT / KEYLESS ENTRY _0261053 ENTRY AND START SYSTEM(for Entry Function) J

THEFT DETERRENT / KEYLESS ENTRY  ENTRY AND START SYSTEM(for Entry Function)  Front Passenger Side Door Entry Lock and Unlock Functions do not Operate  


DESCRIPTION

When the front passenger side door entry lock and unlock functions do not operate, one of the following may be malfunctioning: 1) the power door lock control system, 2) the front door outside handle (for front passenger side), or 3) the certification ECU.

WIRING DIAGRAM

B243941E02
1.189,0.344 1.573,0.504 0.384,0.160 10 ANT1 1.186,0.645 1.585,0.806 0.399,0.160 10 ANT2 0.242,1.724 1.003,1.885 0.761,0.160 10 N1*1, O1*2 1.237,1.3 1.581,1.443 0.344,0.144 10 GND 1.669,0.535 1.774,0.693 0.105,0.158 10 3 1.677,1.194 1.783,1.347 0.105,0.153 10 2 1.451,0.976 1.583,1.119 0.132,0.144 10 B 1.677,0.87 1.783,1.023 0.105,0.153 10 5 1.671,0.255 1.776,0.400 0.105,0.145 10 6 5.652,0.347 6.069,0.513 0.416,0.167 10 CLG2 5.656,0.647 6.086,0.803 0.430,0.156 10 CG2B 5.648,0.967 6.063,1.131 0.415,0.164 10 POS2 5.443,0.249 5.559,0.406 0.116,0.157 10 5 5.443,0.553 5.568,0.718 0.124,0.166 10 6 5.365,0.878 5.560,1.040 0.195,0.162 10 33 5.448,1.737 5.746,1.892 0.298,0.155 10 G38 5.448,1.89 6.638,2.042 1.190,0.152 10 Certification ECU 0.243,1.871 4.395,2.054 4.152,0.183 10 Front Door Outside Handle Assembly (for Front Passenger Side) 0.234,2.171 0.948,2.314 0.714,0.143 10 *1: for LHD 0.234,2.457 1.027,2.599 0.793,0.143 10 *2: for RHD

CAUTION / NOTICE / HINT

NOTICE:
·

The entry and start system (for Entry Function) uses a multiplex communication system (LIN communication system) and the CAN communication system. Inspect the communication function by following How to Proceed with Troubleshooting (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM (for Entry Function)>HOW TO PROCEED WITH TROUBLESHOOTING). Troubleshoot the entry and start system (for Entry Function) after confirming that the communication systems are functioning properly.

·

When using the intelligent tester with the engine switch off to troubleshoot: Connect the intelligent tester to the DLC3 and turn a courtesy light switch on and off at 1.5-second intervals until communication between the intelligent tester and vehicle begins.

·

Check that there are no electrical key transmitters in the vehicle.

·

Before performing the inspection, check that DTC B1242 (wireless door lock control) is not output (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM (for Entry Function)>DTC CHECK / CLEAR).

·

When checking the entry lock operation multiple times, the lock operation may be limited to 2 consecutive operations depending on the settings. In order to perform the entry lock operation 3 or more times, an unlock operation must be performed once (any type of unlock operation is sufficient). However, only consecutive entry lock operations are limited. Using the wireless lock or other types of lock operations, it is possible to perform consecutive lock operations without this limitation.

·

Before replacing the certification ECU, refer to the Service Bulletin.



PROCEDURE

1.CHECK POWER DOOR LOCK OPERATION
a.

When the door control switch on the multiplex network master switch assembly is operated, check that the doors unlock and lock according to the switch operation (See page Vehicle Interior>DOOR LOCK>POWER DOOR LOCK CONTROL SYSTEM>OPERATION CHECK).

OK:

Door locks operate normally.




OK

2.CHECK WAVE ENVIRONMENT

NG

2.CHECK WAVE ENVIRONMENT
a.

Bring the electrical key transmitter approximately 0.3 m (0.984 ft.) from the door outside handle (for front passenger side) and perform a front passenger side door entry lock and unlock operation check (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM (for Entry Function)>OPERATION CHECK).

NOTICE:

If the key is brought within 0.2 m (0.656 ft.) of the door handle, communication is not possible.


HINT:
·

When the electrical key transmitter is brought near the front passenger side door outside handle, the possibility of wave interference decreases, and it can be determined if wave interference is causing the problem symptom.

·

If the operation check is normal, the possibility of wave interference is high. Also, added vehicle components may cause wave interference. If installed, remove them and perform the operation check.



OK:

Entry function operates normally.




OK

AFFECTED BY WAVE INTERFERENCE

NG

3.READ VALUE USING INTELLIGENT TESTER (DOOR LOCK POSITION SWITCH)
3.READ VALUE USING INTELLIGENT TESTER (DOOR LOCK POSITION SWITCH)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the intelligent tester on.


d.

Enter the following menus: Body / Main Body / Data List.


e.

Read the Data List according to the display on the intelligent tester.

Main Body
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
FR Door Lock Pos*1 Front RH side door lock position switch signal / UNLOCK or LOCK UNLOCK: Front RH side door unlocked
LOCK: Front RH side door locked
-
FL Door Lock Pos*2 Front LH side door lock position switch signal / UNLOCK or LOCK UNLOCK: Front LH side door unlocked
LOCK: Front LH side door locked
-

*1: for LHD

*2: for RHD


OK:

On the intelligent tester screen, the display changes between LOCK and UNLOCK as shown in the chart above.




OK

4.CHECK HARNESS AND CONNECTOR (FRONT DOOR OUTSIDE HANDLE - CERTIFICATION ECU)

NG

GO TO POWER DOOR LOCK CONTROL SYSTEM (Proceed to Only Front Passenger Door Lock/Unlock Functions do not Operate)

4.CHECK HARNESS AND CONNECTOR (FRONT DOOR OUTSIDE HANDLE - CERTIFICATION ECU)
a.

Disconnect the N1*1 or O1*2 handle connector.

*1: for LHD

*2: for RHD



b.

Disconnect the G38 ECU connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for LHD:
Tester Connection Condition Specified Condition
N1-3 (ANT2) - G38-6 (CG2B) Always Below 1 Ω
N1-6 (ANT1) - G38-5 (CLG2) Always Below 1 Ω
N1-5 (B) - G38-33 (POS2) Always Below 1 Ω
N1-2 (GND) - Body ground Always Below 1 Ω
G38-6 (CG2B) - Body ground Always 10 kΩ or higher
G38-5 (CLG2) - Body ground Always 10 kΩ or higher
G38-33 (POS2) - Body ground Always 10 kΩ or higher

for RHD:
Tester Connection Condition Specified Condition
O1-3 (ANT2) - G38-6 (CG2B) Always Below 1 Ω
O1-6 (ANT1) - G38-5 (CLG2) Always Below 1 Ω
O1-5 (B) - G38-33 (POS2) Always Below 1 Ω
O1-2 (GND) - Body ground Always Below 1 Ω
G38-6 (CG2B) - Body ground Always 10 kΩ or higher
G38-5 (CLG2) - Body ground Always 10 kΩ or higher
G38-33 (POS2) - Body ground Always 10 kΩ or higher




OK

5.CHECK CERTIFICATION ECU (OUTPUT SIGNAL)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK CERTIFICATION ECU (OUTPUT SIGNAL)
a.
U169645E02
1.875,1.052 2.531,0.917 false 1.875,1.25 2.406,1.594 false 0.875,1.594 1.688,1.25 false 1.552,0.219 1.75,0.448 0.198,0.229 10 false *A 0.135,0.052 0.448,0.406 0.313,0.354 10 false *a 2.344,0.229 2.604,0.49 0.26,0.26 10 false *B 1.198,0.198 1.479,0.365 0.281,0.167 10 false N1 1.979,0.198 2.271,0.354 0.292,0.156 10 false O1 2.5,1.563 2.885,1.75 0.385,0.188 10 false ANT1 2.625,0.781 3.01,0.969 0.385,0.188 10 false ANT2 0.74,1.531 0.865,1.677 0.125,0.146 10 false B

Disconnect the N1*1 or O1*2 handle connector.

*1: for LHD

*2: for RHD



b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
for LHD:
Tester Connection Switch Condition Specified Condition
N1-3 (ANT2) - N1-6 (ANT1) Engine switch off, all doors closed, key not in cabin and transmitter lock switch not pressed → pressed No pulse generation → Pulse generation
N1-5 (B) - Body ground Engine switch off → on (IG) 9 to 14 V → Below 2 V

for RHD:
Tester Connection Switch Condition Specified Condition
O1-3 (ANT2) - O1-6 (ANT1) Engine switch off, all doors closed, key not in cabin and transmitter lock switch not pressed → pressed No pulse generation → Pulse generation
O1-5 (B) - Body ground Engine switch off → on (IG) 9 to 14 V → Below 2 V


Text in Illustration
*A for LHD
*B for RHD
*a Front view of wire harness connector
(to Front Door Outside Handle Assembly [for Front Passenger Side])



OK

6.REPLACE FRONT DOOR OUTSIDE HANDLE ASSEMBLY (FOR FRONT PASSENGER SIDE)

NG

REPLACE CERTIFICATION ECU

6.REPLACE FRONT DOOR OUTSIDE HANDLE ASSEMBLY (FOR FRONT PASSENGER SIDE)
a.

Temporarily replace the front door outside handle assembly (for front passenger side) with a new or normally functioning one (See page Vehicle Exterior>DOOR / HATCH>FRONT DOOR>DISASSEMBLY).



NEXT

7.CHECK FRONT DOOR OUTSIDE HANDLE ASSEMBLY (OPERATION)
7.CHECK FRONT DOOR OUTSIDE HANDLE ASSEMBLY (OPERATION)
a.

Check that the entry functions operate normally (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM (for Entry Function)>OPERATION CHECK).

OK:

Entry functions operate normally.




OK

END (FRONT DOOR OUTSIDE HANDLE ASSEMBLY IS DEFECTIVE)

NG

REPLACE CERTIFICATION ECU