Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › ENTRY AND START SYSTEM (for Entry Function) › 2015.06–2017.08
RM27T0E _58 Vehicle Interior _053731 THEFT DETERRENT / KEYLESS ENTRY _0261053 ENTRY AND START SYSTEM(for Entry Function) J

THEFT DETERRENT / KEYLESS ENTRY  ENTRY AND START SYSTEM(for Entry Function)  Driver Side Door Entry Lock Function does not Operate  


DESCRIPTION

If the driver side door entry lock function does not operate but the entry unlock function operates, the communication between the vehicle and electrical key transmitter is normal. The malfunctioning part may be an entry lock sensor circuit (front door outside handle assembly [for driver side] → certification ECU).

WIRING DIAGRAM

B243940E03
1.158,0.581 1.617,0.741 0.458,0.160 10 TRG+ 0.246,1.675 1.008,1.836 0.761,0.160 10 O1*1, N1*2 1.675,0.484 1.781,0.629 0.105,0.145 10 1 5.657,0.576 6.073,0.742 0.416,0.167 10 TSW1 5.652,1.448 5.830,1.612 0.178,0.164 10 E 5.363,0.478 5.563,0.635 0.201,0.157 10 18 5.37,1.359 5.564,1.521 0.195,0.162 10 15 5.453,1.966 5.751,2.121 0.298,0.155 10 G38 5.453,2.119 6.643,2.271 1.190,0.152 10 Certification ECU 0.248,1.821 3.677,2.005 3.429,0.183 10 Front Door Outside Handle Assembly (for Driver Side) 0.239,2.122 0.953,2.265 0.714,0.143 10 *1: for LHD 0.239,2.408 1.032,2.550 0.793,0.143 10 *2: for RHD

CAUTION / NOTICE / HINT

NOTICE:
·

The entry and start system (for Entry Function) uses a multiplex communication system (LIN communication system) and the CAN communication system. Inspect the communication function by following How to Proceed with Troubleshooting (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM (for Entry Function)>HOW TO PROCEED WITH TROUBLESHOOTING). Troubleshoot the entry and start system (for Entry Function) after confirming that the communication systems are functioning properly.

·

When using the intelligent tester with the engine switch off to troubleshoot: Connect the intelligent tester to the DLC3 and turn a courtesy light switch on and off at 1.5-second intervals until communication between the intelligent tester and vehicle begins.

·

Check that there are no electrical key transmitters in the vehicle.

·

Before performing the inspection, check that DTC B1242 (wireless door lock control) is not output (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM (for Entry Function)>DTC CHECK / CLEAR).

·

When checking the entry lock operation multiple times, the lock operation may be limited to 2 consecutive operations depending on the settings. In order to perform the entry lock operation 3 or more times, an unlock operation must be performed once (any type of unlock operation is sufficient). However, only consecutive entry lock operations are limited. Using the wireless lock or other types of lock operations, it is possible to perform consecutive lock operations without this limitation.

·

Before replacing the certification ECU, refer to the Service Bulletin.



PROCEDURE

1.CHECK POWER DOOR LOCK OPERATION
a.

When the door control switch on the multiplex network master switch assembly is operated, check that the doors unlock and lock according to the switch operation (See page Vehicle Interior>DOOR LOCK>POWER DOOR LOCK CONTROL SYSTEM>OPERATION CHECK).

OK:

Door locks operate normally.




OK

2.READ VALUE USING INTELLIGENT TESTER (DOOR LOCK POSITION SWITCH)

NG

2.READ VALUE USING INTELLIGENT TESTER (DOOR LOCK POSITION SWITCH)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the intelligent tester on.


d.

Enter the following menus: Body / Main Body / Data List.


e.

Read the Data List according to the display on the intelligent tester.

Main Body
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
FR Door Lock Pos*1 Front RH side door lock position switch signal / UNLOCK or LOCK UNLOCK: Front RH side door unlocked
LOCK: Front RH side door locked
-
FL Door Lock Pos*2 Front LH side door lock position switch signal / UNLOCK or LOCK UNLOCK: Front LH side door unlocked
LOCK: Front LH side door locked
-

*1: for RHD

*2: for LHD


OK:

On the intelligent tester screen, the display changes between LOCK and UNLOCK as shown in the chart above.




OK

3.READ VALUE USING INTELLIGENT TESTER (LOCK SENSOR)

NG

GO TO POWER DOOR LOCK CONTROL SYSTEM (Proceed to Only Driver Door Lock/Unlock Functions do not Operate)

3.READ VALUE USING INTELLIGENT TESTER (LOCK SENSOR)
a.

Using the intelligent tester, read the Data List (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM (for Entry Function)>DATA LIST / ACTIVE TEST).

Entry&Start
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
D-Door Trigger Switch Driver side door lock sensor / ON or OFF ON: Driver side door lock sensor touched
OFF: Driver side door lock sensor not touched
-

OK:

"ON" (lock sensor is touched) and "OFF" (lock sensor is not touched) appear on the screen.




OK

REPLACE CERTIFICATION ECU

NG

4.CHECK HARNESS AND CONNECTOR (FRONT DOOR OUTSIDE HANDLE - CERTIFICATION ECU)
4.CHECK HARNESS AND CONNECTOR (FRONT DOOR OUTSIDE HANDLE - CERTIFICATION ECU)
a.

Disconnect the O1*1 or N1*2 handle connector.

*1: for LHD

*2: for RHD



b.

Disconnect the G38 ECU connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for LHD:
Tester Connection Condition Specified Condition
O1-1 (TRG+) - G38-18 (TSW1) Always Below 1 Ω
G38-18 (TSW1) - Body ground Always 10 kΩ or higher
G38-15 (E) - Body ground Always Below 1 Ω

for RHD:
Tester Connection Condition Specified Condition
N1-1 (TRG+) - G38-18 (TSW1) Always Below 1 Ω
G38-18 (TSW1) - Body ground Always 10 kΩ or higher
G38-15 (E) - Body ground Always Below 1 Ω




OK

5.CHECK FRONT DOOR OUTSIDE HANDLE ASSEMBLY (LOCK SENSOR)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK FRONT DOOR OUTSIDE HANDLE ASSEMBLY (LOCK SENSOR)
a.

Measure the voltage according to the value(s) in the table below.

U169664E01
1.025,0.173 1.241,0.384 0.217,0.212 10 *a 2.411,0.248 2.708,0.427 0.297,0.179 10 G38 3.748,0.463 4.164,0.628 0.416,0.165 10 TSW1 0.896,0.701 1.054,0.872 0.158,0.172 10 E 1.482,1.143 1.017,0.763 false 3.71,0.534 3.549,1.259 false

Text in Illustration
*a Component with harness connected
(Certification ECU)
- -

Standard Voltage:
Tester Connection Switch Condition Specified Condition
G38-18 (TSW1) - G38-15 (E) Engine switch off, all doors closed and lock sensor (for driver side) off → on Pulse generation → Below 2 V




OK

REPLACE CERTIFICATION ECU

NG

REPLACE FRONT DOOR OUTSIDE HANDLE ASSEMBLY (FOR DRIVER SIDE)