Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › ENTRY AND START SYSTEM (for Entry Function) › 2015.06–2017.08
RM27T0E _58 Vehicle Interior _053731 THEFT DETERRENT / KEYLESS ENTRY _0261053 ENTRY AND START SYSTEM(for Entry Function) J

THEFT DETERRENT / KEYLESS ENTRY  ENTRY AND START SYSTEM(for Entry Function)  Room Oscillator does not Recognize Key  


DESCRIPTION

If the room oscillator does not recognize the key, one of the following may be the cause: 1) communication between the indoor No. 1 electrical key antenna (front floor) and electrical key transmitter cannot be performed; 2) communication between the indoor No. 2 electrical key antenna (rear floor) and electrical key transmitter cannot be performed; or 3) communication between the indoor No. 3 electrical key antenna (inside luggage) and electrical key transmitter cannot be performed.

WIRING DIAGRAM

B242477E02
0.643,1.465 1.005,1.603 0.362,0.138 10 i1 0.643,1.62 4.472,1.758 3.829,0.138 10 Indoor No. 1 Electrical Key Antenna Assembly (Front Floor) 0.643,3.118 1.649,3.257 1.006,0.138 10 R14*1, s1*2 0.643,3.259 4.680,3.398 4.037,0.138 10 Indoor No. 2 Electrical Key Antenna Assembly (Rear Floor) 5.505,4.737 5.788,4.878 0.283,0.141 10 G38 5.505,4.892 6.630,5.068 1.126,0.176 10 Certification ECU 2.706,0.573 3.125,0.728 0.419,0.155 10 CLGB 3.172,0.573 3.276,0.728 0.104,0.155 10 3 3.175,0.957 3.279,1.112 0.104,0.155 10 1 5.528,0.573 5.631,0.728 0.103,0.155 10 8 5.809,0.673 6.217,0.827 0.408,0.155 10 CG5B 5.809,1.053 6.217,1.208 0.408,0.155 10 CLG5 5.548,0.957 5.645,1.112 0.097,0.155 10 7 5.522,2.229 5.712,2.384 0.190,0.155 10 25 5.809,2.341 6.217,2.496 0.408,0.155 10 CG6B 5.809,2.692 6.217,2.847 0.408,0.155 10 CLG6 5.533,2.598 5.707,2.753 0.173,0.155 10 24 2.709,0.957 3.128,1.112 0.419,0.155 10 CLG3 2.7,2.229 3.118,2.384 0.419,0.155 10 CLGB 3.166,2.229 3.270,2.384 0.104,0.155 10 2 3.161,2.598 3.265,2.753 0.104,0.155 10 1 2.695,2.598 3.114,2.753 0.419,0.155 10 CLG4 0.643,4.758 0.931,4.896 0.289,0.138 10 R15 0.643,4.913 4.785,5.051 4.143,0.138 10 Indoor No. 3 Electrical Key Antenna Assembly (Inside Luggage) 0.277,5.241 1.204,5.380 0.927,0.138 10 *1: for 5 Door 0.277,5.523 1.169,5.662 0.893,0.138 10 *2: for 3 Door 5.522,3.853 5.712,4.008 0.190,0.155 10 27 5.809,3.952 6.217,4.107 0.408,0.155 10 CG7B 5.809,4.318 6.217,4.472 0.408,0.155 10 CLG7 5.533,4.236 5.707,4.391 0.173,0.155 10 26 2.7,3.853 3.118,4.008 0.419,0.155 10 CLGB 3.166,3.853 3.270,4.008 0.104,0.155 10 2 3.161,4.236 3.265,4.391 0.104,0.155 10 1 2.695,4.236 3.114,4.391 0.419,0.155 10 CLG6

CAUTION / NOTICE / HINT

NOTICE:
·

The entry and start system (for Entry Function) uses a multiplex communication system (LIN communication system) and the CAN communication system. Inspect the communication function by following How to Proceed with Troubleshooting (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM (for Entry Function)>HOW TO PROCEED WITH TROUBLESHOOTING). Troubleshoot the entry and start system (for Entry Function) after confirming that the communication systems are functioning properly.

·

When using the intelligent tester with the engine switch off to troubleshoot: Connect the intelligent tester to the vehicle and turn a courtesy light switch on and off at 1.5 second intervals until communication between the intelligent tester and vehicle begins.

·

Before replacing the certification ECU, refer to the Service Bulletin.



PROCEDURE

1.CHECK ENTRY AND START SYSTEM (START FUNCTION)
a.

Remove the battery of the electrical key transmitter (See page Vehicle Interior>DOOR LOCK>TRANSMITTER BATTERY(w/ Entry and Start System)>REPLACEMENT).


U169646E02
1.479,0.906 1.698,0.51 1.698,0.51 1.865,0.51 false 2.396,2 2.521,2.281 2.521,2.281 2.635,2.281 false 1.906,0.396 2.083,0.563 0.177,0.167 10 false *1 2.688,2.188 2.865,2.354 0.177,0.167 10 false *2

b.

With the clutch pedal (for Manual Transmission) or brake pedal (for Automatic Transmission) depressed, touch the key to the engine switch.


c.

When operating the engine switch, check whether the power source mode changes.

HINT:
·

When the electrical key transmitter cannot be verified even though it is in the operating range of the start function, the engine start check can be performed by removing the transmitter battery from the electrical key transmitter and holding the transmitter against the engine switch.

·

When performing the check, if the power source mode changes, there is a problem with key certification inside the cabin.



OK:

Power source mode changes.


Text in Illustration
*1 Engine Switch
*2 Electrical Key Transmitter



OK

2.CHECK WAVE ENVIRONMENT

NG

2.CHECK WAVE ENVIRONMENT
a.

Install the battery to the electrical key transmitter (See page Vehicle Interior>DOOR LOCK>TRANSMITTER BATTERY(w/ Entry and Start System)>REPLACEMENT).


b.

Move the electrical key transmitter as described below and perform the operation inspection (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM (for Entry Function)>OPERATION CHECK).

i.

Bring the electrical key transmitter near the indoor No. 1 electrical key antenna (front floor) and perform an engine control system start check.

NOTICE:

If the key is brought within 0.2 m (0.656 ft.) of the indoor No. 1 electrical key antenna (front floor), communication is not possible.



ii.

Bring the electrical key transmitter near the indoor No. 2 electrical key antenna (rear floor) and perform an engine control system start check.

NOTICE:

If the key is brought within 0.2 m (0.656 ft.) of the indoor No. 2 electrical key antenna (rear floor), communication is not possible.



iii.

Bring the electrical key transmitter near the indoor No. 3 electrical key antenna (inside luggage) and perform an engine control system start check.

NOTICE:

If the key is brought within 0.2 m (0.656 ft.) of the indoor No. 3 electrical key antenna (rear floor), communication is not possible.


HINT:
·

When the electrical key transmitter is brought near the indoor electrical key antenna, the possibility of wave interference decreases, and it can be determined if wave interference is causing the problem symptom.

·

If the inspection result is that the operation check is normal, the possibility of wave interference is high. Also, added vehicle components may cause wave interference. If installed, remove them and perform the operation check.



OK:

Engine can be started.





OK

AFFECTED BY WAVE INTERFERENCE

NG

3.CHECK ELECTRICAL KEY ANTENNAS IN KEY DIAGNOSTIC MODE
3.CHECK ELECTRICAL KEY ANTENNAS IN KEY DIAGNOSTIC MODE
a.

Check the following antennas in the key diagnostic mode (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM (for Entry Function)>SYSTEM DESCRIPTION).

i.

Check the indoor No. 1 electrical key antenna (front floor).

When the electrical key transmitter is at the inspection point, check that the wireless door lock buzzer sounds.


ii.

Check the indoor No. 2 electrical key antenna (rear floor.

When the electrical key transmitter is at the inspection point, check that the wireless door lock buzzer sounds.


iii.

Check the indoor No. 3 electrical key antenna (inside luggage).

When the electrical key transmitter is at the inspection point, check that the wireless door lock buzzer sounds.

HINT:
·

If the buzzer sounds, it can be determined that the vehicle interior transmitters are operating normally.

·

It is possible to check which indoor electrical key antenna (front floor, rear floor or inside luggage) is operating by the sounding of the buzzer.

·

If the buzzer does not sound for any indoor electrical key antennas, the certification ECU circuit may have a malfunction.



OK:

Wireless door lock buzzer sounds.


Result
Result Proceed to
Front operation check fails A
Rear operation check fails B
Luggage operation check fails C
Front, rear and luggage operation checks are normal D




A

4.CHECK HARNESS AND CONNECTOR (INDOOR NO. 1 ELECTRICAL KEY ANTENNA - CERTIFICATION ECU)

B

8.CHECK HARNESS AND CONNECTOR (INDOOR NO. 2 ELECTRICAL KEY ANTENNA - CERTIFICATION ECU)

C

12.CHECK HARNESS AND CONNECTOR (INDOOR NO. 3 ELECTRICAL KEY ANTENNA - CERTIFICATION ECU)

D

REPLACE CERTIFICATION ECU

4.CHECK HARNESS AND CONNECTOR (INDOOR NO. 1 ELECTRICAL KEY ANTENNA - CERTIFICATION ECU)
a.

Disconnect the i1 antenna connector.


b.

Disconnect the G38 ECU connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
i1-1 (CLG3) - G38-7 (CLG5) Always Below 1 Ω
i1-3 (CLGB) - G38-8 (CG5B) Always Below 1 Ω
G38-7 (CLG5) - Body ground Always 10 kΩ or higher
G38-8 (CG5B) - Body ground Always 10 kΩ or higher




OK

5.CHECK CERTIFICATION ECU (OUTPUT SIGNAL)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK CERTIFICATION ECU (OUTPUT SIGNAL)
a.
U169649E02
1.979,1.375 2.583,1.823 false 1.469,1.365 0.771,1.823 false 0.115,0.021 0.333,0.167 0.219,0.146 10 false *a 1.635,0.229 1.844,0.49 0.208,0.26 10 false i1 2.635,1.771 3.052,1.948 0.417,0.177 10 false CLGB 0.271,1.781 0.708,1.958 0.438,0.177 10 false CLG3

Disconnect the i1 antenna connector.


b.

Measure the voltage according to the value(s) in the table below.

OK:
Tester Connection Switch Condition Specified Condition
i1-1 (CLG3) - i1-3 (CLGB) Engine switch off, all doors closed, key not in cabin and lock sensor off → on No pulse generation → pulse generation


Text in Illustration
*a Front view of wire harness connector
(to Indoor No. 1 Electrical Key Antenna [Front Floor])



OK

6.REPLACE INDOOR NO. 1 ELECTRICAL KEY ANTENNA ASSEMBLY (FRONT FLOOR)

NG

REPLACE CERTIFICATION ECU

6.REPLACE INDOOR NO. 1 ELECTRICAL KEY ANTENNA ASSEMBLY (FRONT FLOOR)
a.

Temporarily replace the indoor No. 1 electrical key antenna (front floor) with a new or normally functioning one (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ELECTRICAL KEY OSCILLATOR(for Front Floor)>REMOVAL).



NEXT

7.CHECK ELECTRICAL KEY ANTENNA IN KEY DIAGNOSTIC MODE
7.CHECK ELECTRICAL KEY ANTENNA IN KEY DIAGNOSTIC MODE
a.

Check the following antenna in the key diagnostic mode (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM (for Entry Function)>SYSTEM DESCRIPTION).

i.

Check the indoor No. 1 electrical key antenna (front floor).

When the electrical key transmitter is at the inspection point, check that the wireless door lock buzzer sounds.

OK:

Wireless door lock buzzer sounds.





OK

END (INDOOR NO. 1 ELECTRICAL KEY ANTENNA ASSEMBLY IS DEFECTIVE)

NG

REPLACE CERTIFICATION ECU

8.CHECK HARNESS AND CONNECTOR (INDOOR NO. 2 ELECTRICAL KEY ANTENNA - CERTIFICATION ECU)
a.

Disconnect the R14*1 or s1*2 antenna connector.

*1: for 5 Door

*2: for 3 Door



b.

Disconnect the G38 ECU connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for 5 Door
Tester Connection Condition Specified Condition
R14-1 (CLG4) - G38-24 (CLG6) Always Below 1 Ω
R14-2 (CLGB) - G38-25 (CG6B) Always Below 1 Ω
G38-24 (CLG6) - Body ground Always 10 kΩ or higher
G38-25 (CG6B) - Body ground Always 10 kΩ or higher

for 3 Door
Tester Connection Condition Specified Condition
s1-1 (CLG4) - G38-24 (CLG6) Always Below 1 Ω
s1-2 (CLGB) - G38-25 (CG6B) Always Below 1 Ω
G38-24 (CLG6) - Body ground Always 10 kΩ or higher
G38-25 (CG6B) - Body ground Always 10 kΩ or higher




OK

9.CHECK CERTIFICATION ECU (OUTPUT SIGNAL)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

9.CHECK CERTIFICATION ECU (OUTPUT SIGNAL)
a.
U169672E02
1.875,1.344 2.583,1.896 false 1.615,1.344 0.771,1.885 false 0.115,0.083 0.333,0.229 0.219,0.146 10 false *a 1.01,0.219 1.323,0.396 0.313,0.177 10 false R14 1.49,0.198 1.677,0.375 0.188,0.177 10 false *A 2.635,1.844 3.052,2.021 0.417,0.177 10 false CLGB 0.271,1.844 0.708,2.021 0.438,0.177 10 false CLG4 2.052,0.219 2.229,0.396 0.177,0.177 10 false s1 2.479,0.198 2.854,0.542 0.375,0.344 10 false *B

Disconnect the R14*1 or s1*2 antenna connector.

*1: for 5 Door

*2: for 3 Door



b.

Measure the voltage according to the value(s) in the table below.

OK:
for 5 Door
Tester Connection Switch Condition Specified Condition
R14-1 (CLG4) - R14-2 (CLGB) Engine switch off, all doors closed, key not in cabin and lock sensor off → on No pulse generation → pulse generation

for 3 Door
Tester Connection Switch Condition Specified Condition
s1-1 (CLG4) - s1-2 (CLGB) Engine switch off, all doors closed, key not in cabin and lock sensor off → on No pulse generation → pulse generation


Text in Illustration
*A for 5 Door
*B for 3 Door
*a Front view of wire harness connector
(to Indoor No. 2 Electrical Key Antenna [Rear Floor])



OK

10.REPLACE INDOOR NO. 2 ELECTRICAL KEY ANTENNA ASSEMBLY (REAR FLOOR)

NG

REPLACE CERTIFICATION ECU

10.REPLACE INDOOR NO. 2 ELECTRICAL KEY ANTENNA ASSEMBLY (REAR FLOOR)
a.

Temporarily replace the indoor No. 2 electrical key antenna (rear floor) with a new or normally functioning one (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ELECTRICAL KEY OSCILLATOR (for Rear Floor)>REMOVAL).



NEXT

11.CHECK ELECTRICAL KEY ANTENNA IN KEY DIAGNOSTIC MODE
11.CHECK ELECTRICAL KEY ANTENNA IN KEY DIAGNOSTIC MODE
a.

Check the following antenna in the key diagnostic mode (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM (for Entry Function)>SYSTEM DESCRIPTION).

i.

Check the indoor No. 2 electrical key antenna (rear floor).

When the electrical key transmitter is at the inspection point, check that the wireless door lock buzzer sounds.

OK:

Wireless door lock buzzer sounds.





OK

END (INDOOR NO. 2 ELECTRICAL KEY ANTENNA ASSEMBLY IS DEFECTIVE)

NG

REPLACE CERTIFICATION ECU

12.CHECK HARNESS AND CONNECTOR (INDOOR NO. 3 ELECTRICAL KEY ANTENNA - CERTIFICATION ECU)
a.

Disconnect the R15 antenna connector.


b.

Disconnect the G38 ECU connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
R15-1 (CLG6) - G38-26 (CLG7) Always Below 1 Ω
R15-2 (CLGB) - G38-27 (CG7B) Always Below 1 Ω
G38-26 (CLG7) - Body ground Always 10 kΩ or higher
G38-27 (CG7B) - Body ground Always 10 kΩ or higher




OK

13.CHECK CERTIFICATION ECU (OUTPUT SIGNAL)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

13.CHECK CERTIFICATION ECU (OUTPUT SIGNAL)
a.
U169673E02
1.875,1.344 2.583,1.896 false 1.615,1.344 0.771,1.885 false 0.083,0.021 0.302,0.167 0.219,0.146 10 false *a 1.573,0.281 1.885,0.458 0.313,0.177 10 false R15 2.635,1.844 3.052,2.021 0.417,0.177 10 false CLGB 0.271,1.844 0.708,2.021 0.438,0.177 10 false CLG6

Disconnect the R15 antenna connector.


b.

Measure the voltage according to the value(s) in the table below.

OK:
Tester Connection Switch Condition Specified Condition
R15-1 (CLG6) - R15-2 (CLGB) Engine switch off, all doors closed, key not in cabin and lock sensor off → on No pulse generation → pulse generation


Text in Illustration
*a Front view of wire harness connector
(to Indoor No. 3 Electrical Key Antenna [Inside Luggage])



OK

14.REPLACE INDOOR NO. 3 ELECTRICAL KEY ANTENNA ASSEMBLY (INSIDE LUGGAGE)

NG

REPLACE CERTIFICATION ECU

14.REPLACE INDOOR NO. 3 ELECTRICAL KEY ANTENNA ASSEMBLY (INSIDE LUGGAGE)
a.

Temporarily replace the indoor No. 3 electrical key antenna (inside luggage) with a new or normally functioning one (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ELECTRICAL KEY OSCILLATOR (for Luggage Compartment)>REMOVAL).



NEXT

15.CHECK ELECTRICAL KEY ANTENNA IN KEY DIAGNOSTIC MODE
15.CHECK ELECTRICAL KEY ANTENNA IN KEY DIAGNOSTIC MODE
a.

Check the following antenna in the key diagnostic mode (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM (for Entry Function)>SYSTEM DESCRIPTION).

i.

Check the indoor No. 3 electrical key antenna (inside luggage).

When the electrical key transmitter is at the inspection point, check that the wireless door lock buzzer sounds.

OK:

Wireless door lock buzzer sounds.





OK

END (INDOOR NO. 3 ELECTRICAL KEY ANTENNA ASSEMBLY IS DEFECTIVE)

NG

REPLACE CERTIFICATION ECU