Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › ENTRY AND START SYSTEM (for Entry Function) › 2015.06–2017.08
RM27T0E _58 Vehicle Interior _053731 THEFT DETERRENT / KEYLESS ENTRY _0261053 ENTRY AND START SYSTEM(for Entry Function) C

THEFT DETERRENT / KEYLESS ENTRY  ENTRY AND START SYSTEM(for Entry Function)  B27A2  Open in Front Passenger Side Electrical Antenna Circuit  


DESCRIPTION

The certification ECU generates a request signal and transmits the signal to the front door outside handle assembly (for front passenger side) at an interval of 250 ms. The front door outside handle assembly (for front passenger side) detects when the electrical key is brought close to the vehicle, and when a request signal is received from within 1.0 m (3.28 ft.) of the front passenger door, the signal is transmitted at an interval of 250 ms. DTC B27A2 is stored by the certification ECU when an open circuit is detected in the circuit between the certification ECU and front door outside handle assembly (for front passenger side) (CLG2 - ANT1, CG2B - ANT2).

DTC Code DTC Detection Condition Trouble Area
B27A2 An open circuit is detected in the circuit between the certification ECU and front door outside handle assembly (for front passenger side) (CLG2 - ANT1, CG2B - ANT2).
·

Harness or connector

·

Front door outside handle assembly (for front passenger side)

·

Certification ECU



WIRING DIAGRAM

B243939E02
1.197,0.354 1.582,0.514 0.384,0.160 10 ANT1 1.19,0.826 1.589,0.986 0.399,0.160 10 ANT2 0.246,1.742 1.008,1.902 0.761,0.160 10 N1*1, O1*2 1.242,1.309 1.585,1.453 0.344,0.144 10 GND 1.674,0.715 1.779,0.873 0.105,0.158 10 3 1.682,1.203 1.787,1.356 0.105,0.153 10 2 1.675,0.264 1.781,0.409 0.105,0.145 10 6 5.657,0.356 6.073,0.523 0.416,0.167 10 CLG2 5.657,0.828 6.086,0.984 0.430,0.156 10 CG2B 5.652,1.296 5.830,1.460 0.178,0.164 10 E 5.448,0.258 5.564,0.416 0.116,0.157 10 5 5.448,0.733 5.572,0.899 0.124,0.166 10 6 5.37,1.207 5.564,1.369 0.195,0.162 10 15 5.453,1.747 5.751,1.902 0.298,0.155 10 G38 5.453,1.9 6.643,2.052 1.190,0.152 10 Certification ECU 0.248,1.888 4.254,2.071 4.006,0.183 10 Front Door Outside Handle Assembly (for Front Passenger Side) 0.239,2.189 0.953,2.331 0.714,0.143 10 *1: for LHD 0.239,2.466 1.032,2.609 0.793,0.143 10 *2: for RHD

CAUTION / NOTICE / HINT

NOTICE:
·

The entry and start system (for Entry Function) uses a multiplex communication system (LIN communication system) and the CAN communication system. Inspect the communication function by following How to Proceed with Troubleshooting (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM (for Entry Function)>HOW TO PROCEED WITH TROUBLESHOOTING). Troubleshoot the entry and start system (for Entry Function) after confirming that the communication systems are functioning properly.

·

When using the intelligent tester with the engine switch off to troubleshoot: Connect the intelligent tester to the DLC3 and turn a courtesy light switch on and off at 1.5-second intervals until communication between the intelligent tester and vehicle begins.

·

Before replacing the certification ECU, refer to the Service Bulletin.



PROCEDURE

1.CHECK CONNECTOR CONNECTION
a.

Turn the engine switch off.


b.

Check that the connectors are properly connected to the certification ECU and front door outside handle assembly (for front passenger side).

OK:

Connectors are properly connected.




OK

2.CHECK HARNESS AND CONNECTOR (FRONT DOOR OUTSIDE HANDLE - CERTIFICATION ECU)

NG

CONNECT CONNECTORS PROPERLY

2.CHECK HARNESS AND CONNECTOR (FRONT DOOR OUTSIDE HANDLE - CERTIFICATION ECU)
a.

Disconnect the N1*1 or O1*2 handle connector.

*1: for LHD

*2: for RHD



b.

Disconnect the G38 ECU connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for LHD:
Tester Connection Condition Specified Condition
N1-3 (ANT2) - G38-6 (CG2B) Always Below 1 Ω
N1-6 (ANT1) - G38-5 (CLG2) Always Below 1 Ω
N1-2 (GND) - Body ground Always Below 1 Ω
G38-6 (CG2B) - Body ground Always 10 kΩ or higher
G38-5 (CLG2) - Body ground Always 10 kΩ or higher
G38-15 (E) - Body ground Always Below 1 Ω

for RHD:
Tester Connection Condition Specified Condition
O1-3 (ANT2) - G38-6 (CG2B) Always Below 1 Ω
O1-6 (ANT1) - G38-5 (CLG2) Always Below 1 Ω
O1-2 (GND) - Body ground Always Below 1 Ω
G38-6 (CG2B) - Body ground Always 10 kΩ or higher
G38-5 (CLG2) - Body ground Always 10 kΩ or higher
G38-15 (E) - Body ground Always Below 1 Ω




OK

3.CHECK CERTIFICATION ECU

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK CERTIFICATION ECU
a.

Measure the voltage according to the value(s) in the table below.

U169658E01
1.025,0.173 1.241,0.384 0.217,0.212 10 *a 2.197,0.427 2.494,0.606 0.297,0.179 10 G38 3.508,0.46 3.924,0.625 0.416,0.165 10 CLG2 2.663,0.463 3.106,0.635 0.443,0.172 10 CG2B 3.192,1.135 3.072,0.526 false 0.896,0.701 1.054,0.872 0.158,0.172 10 E 1.482,1.143 1.017,0.763 false 3.47,0.531 3.309,1.137 false

Text in Illustration
*a Component with harness connected
(Certification ECU)
- -

OK:
Tester Connection Switch Condition Specified Condition
G38-5 (CLG2) - G38-15 (E) Engine switch off, all doors closed, key not in cabin and transmitter lock switch not pressed → pressed No pulse generation → Pulse generation
G38-6 (CG2B) - G38-15 (E) Engine switch off, all doors closed, key not in cabin and transmitter lock switch not pressed → pressed No pulse generation → Pulse generation




OK

4.REPLACE FRONT DOOR OUTSIDE HANDLE ASSEMBLY (FOR FRONT PASSENGER SIDE)

NG

REPLACE CERTIFICATION ECU

4.REPLACE FRONT DOOR OUTSIDE HANDLE ASSEMBLY (FOR FRONT PASSENGER SIDE)
a.

Temporarily replace the front door outside handle assembly (for front passenger side) with a new or normally functioning one (See page Vehicle Exterior>DOOR / HATCH>FRONT DOOR>DISASSEMBLY).



NEXT

5.CHECK FOR DTC
5.CHECK FOR DTC

OK

END (FRONT DOOR OUTSIDE HANDLE ASSEMBLY IS DEFECTIVE)

NG

REPLACE CERTIFICATION ECU