Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › THEFT DETERRENT SYSTEM › 2015.06–2016.08
RM27T0E _58 Vehicle Interior _053731 THEFT DETERRENT / KEYLESS ENTRY _0261054 THEFT DETERRENT SYSTEM J

THEFT DETERRENT / KEYLESS ENTRY  THEFT DETERRENT SYSTEM  Theft Warning Siren Circuit  


DESCRIPTION

The theft warning siren assembly (self power siren) has an internal battery. If the vehicle battery cable is disconnected or any of the communication lines are open, the theft warning siren assembly (self power siren) detects this and sounds its siren.

Although the theft warning siren assembly (self power siren) usually sounds by receiving a signal from the main body ECU, the theft warning siren assembly (self power siren) can sound by its internal battery in case the vehicle battery cable is disconnected.

The main body ECU sends an arming signal to the theft warning siren assembly (self power siren) while switching to the armed state, and it sends a disarming signal to the siren while switching to the disarmed state. Also, the main body ECU can cause the theft warning siren assembly (self power siren) to sound by sending an alarm signal during the alarm sounding state.


WIRING DIAGRAM

B159044E08
5.409,1.784 5.690,1.931 0.281,0.147 10 G63 5.314,0.792 5.495,0.939 0.182,0.147 10 18 4.766,0.792 4.894,0.939 0.128,0.147 10 4 3.013,0.463 3.141,0.610 0.128,0.147 10 5 3.013,1.226 3.141,1.374 0.128,0.147 10 2 5.633,0.904 6.073,1.052 0.441,0.147 10 SSCL 4.155,0.904 4.609,1.052 0.455,0.147 10 CONT 3.279,0.575 3.483,0.722 0.205,0.147 10 +B 2.157,0.722 2.883,0.869 0.727,0.147 10 SECURITY 0.381,0.572 1.155,0.790 0.774,0.218 10 from Battery 3.279,1.38 3.733,1.528 0.455,0.147 10 GND 5.409,1.939 7.098,2.255 1.689,0.316 10 Main Body ECU (Multiplex Network Body ECU) 3.03,1.809 3.310,1.957 0.281,0.147 10 Q33 3.02,1.962 4.840,2.298 1.820,0.335 10 Theft Warning Siren Assembly (Self Power Siren)

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


PROCEDURE

1.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (THEFT WARNING SIREN)
a.

Operate the intelligent tester according to the steps on the display and select Active Test (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>THEFT DETERRENT SYSTEM>DATA LIST / ACTIVE TEST).

Main Body
Tester Display Test Part Control Range Diagnostic Note
Security Horn2 Theft warning siren (self power siren) ON/OFF -

OK:

Siren operates normally.




OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

2.CHECK HARNESS AND CONNECTOR (THEFT WARNING SIREN - BATTERY AND BODY GROUND)
2.CHECK HARNESS AND CONNECTOR (THEFT WARNING SIREN - BATTERY AND BODY GROUND)
a.
U169810E01
0.067,0.057 0.256,0.205 0.189,0.148 10 *a 0.607,1.651 0.997,1.823 0.391,0.172 10 GND 2.525,1.651 2.742,1.823 0.217,0.172 10 +B 2.024,1.3 2.507,1.725 false 1.425,1.301 1.043,1.725 false 1.575,0.124 1.860,0.269 0.285,0.145 10 Q33

Disconnect the Q33 siren connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
Q33-2 (GND) - Body ground Always Below 1 Ω



c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
Q33-5 (+B) - Body ground Always 11 to 14 V



Text in Illustration
*a Front view of wire harness connector
(to Theft Warning Siren Assembly)


OK

3.CHECK MAIN BODY ECU (OUTPUT SIGNAL)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK MAIN BODY ECU (OUTPUT SIGNAL)
a.

Using an oscilloscope, check waveform 1.

U169783E01
2.424,0.17 2.602,0.347 0.178,0.178 10 *a 3.189,0.294 3.470,0.451 0.281,0.156 10 G63 3.929,1.653 4.323,1.809 0.394,0.156 10 SSCL 1.63,1.818 1.822,1.974 0.192,0.156 10 *b 2.837,3.139 3.197,3.296 0.360,0.156 10 GND 6.461,3.139 6.821,3.296 0.360,0.156 10 GND 5.232,1.818 5.407,1.974 0.175,0.156 10 *c 4.405,0.294 4.686,0.451 0.281,0.156 10 G64 3.696,1.091 3.911,1.642 false

Text in Illustration
*a Component with harness connected
(Main Body ECU)
*b Waveform 1
*c Waveform 2 - -

Measurement Condition
Item Content
Tester Connection G63-18 (SSCL) - Body ground
Tool Setting 2 V/DIV., 20 ms./DIV.
Condition Switched from armed state or arming preparation state to disarmed state


b.

Using an oscilloscope, check waveform 2.

Measurement Condition
Item Content
Tester Connection G63-18 (SSCL) - Body ground
Tool Setting 2 V/DIV., 20 ms./DIV.
Condition Switched from arming preparation state to armed state


OK:

Waveform is output normally (refer to illustration).



OK

NG

4.CHECK HARNESS AND CONNECTOR (THEFT WARNING SIREN - MAIN BODY ECU)
4.CHECK HARNESS AND CONNECTOR (THEFT WARNING SIREN - MAIN BODY ECU)
a.

Disconnect the Q33 siren connector.


b.

Disconnect the G63 ECU connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
Q33-4 (CONT) - G63-18 (SSCL) Always Below 1 Ω
Q33-4 (CONT) or G63-18 (SSCL) - Body ground Always 10 kΩ or higher




OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR