Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › THEFT DETERRENT SYSTEM › 2015.06–2017.08
RM27T0E _58 Vehicle Interior _053731 THEFT DETERRENT / KEYLESS ENTRY _0261054 THEFT DETERRENT SYSTEM J

THEFT DETERRENT / KEYLESS ENTRY  THEFT DETERRENT SYSTEM  Security Indicator Light Circuit  


DESCRIPTION

When the theft deterrent system is in the disarmed state, the security indicator light flashes continuously when the engine immobiliser system is set, and does not illuminate when the engine immobiliser system is not set.

When the theft deterrent system is in the armed state, the engine immobiliser system is automatically set and the security indicator light flashes continuously.

When the theft deterrent system is in the arming preparation state or alarm sounding state, the main body ECU causes the security indicator light to be illuminated.


WIRING DIAGRAM

B236698E03
0.991,1.99 3.096,2.155 2.105,0.166 10 Security Indicator Light Assembly 1.253,1.142 2.716,1.305 1.463,0.163 10 Security Indicator Light 3.23,1.439 3.385,1.624 0.156,0.186 10 E 3.153,0.896 3.428,1.082 0.275,0.186 10 LP 3.428,1.388 3.790,1.574 0.362,0.186 10 5 3.427,0.846 3.733,1.032 0.306,0.186 10 2 4.655,0.846 4.848,1.032 0.194,0.186 10 23 4.169,2.059 4.363,2.245 0.194,0.186 10 A 0.994,1.823 1.293,2.009 0.300,0.186 10 H23 4.935,0.976 5.259,1.161 0.324,0.186 10 IND 4.16,2.197 7.116,2.369 2.956,0.172 10 Main Body ECU (Multiplex Network Body ECU)

PROCEDURE

1.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (SECURITY INDICATOR LIGHT)
a.

Operate the intelligent tester according to the steps on the display and select Active Test (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>THEFT DETERRENT SYSTEM>DATA LIST / ACTIVE TEST).

Main Body
Tester Display Test Part Control Range Diagnostic Note
Security Indicator Security indicator light ON/OFF The test is possible when the following conditions are met:
·

The key is in the cabin*1

·

The engine switch on (IG)*1

·

The key is in the ignition key cylinder*2



*1: w/ Entry and Start System

*2: w/o Entry and Start System


OK:

Security indicator light can be turned on and off using the intelligent tester.




OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

2.INSPECT SECURITY INDICATOR LIGHT ASSEMBLY
2.INSPECT SECURITY INDICATOR LIGHT ASSEMBLY
a.
B238374E01
0.737,0.653 0.954,0.830 0.217,0.177 10 LP 0.848,1.608 0.978,1.785 0.130,0.177 10 E 1.003,0.735 1.106,0.735 1.106,0.735 1.506,0.967 false 1.004,1.701 1.106,1.701 1.106,1.701 1.507,1.469 false

Remove the security indicator light (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>SECURITY INDICATOR LIGHT ASSEMBLY>REMOVAL).


b.

Apply battery voltage between the terminals of the security indicator light assembly and check that the security indicator light illuminates.

OK:
Measurement Condition Specified Condition
Battery positive (+) → 2 (LP)
Battery negative (-) → 5 (E)
Security indicator light illuminates




OK

3.CHECK HARNESS AND CONNECTOR (SECURITY INDICATOR LIGHT - MAIN BODY ECU AND BODY GROUND)

NG

3.CHECK HARNESS AND CONNECTOR (SECURITY INDICATOR LIGHT - MAIN BODY ECU AND BODY GROUND)
a.

Disconnect the H23 light connector.


b.

c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H23-2 (LP) - A-23 (IND) Always Below 1 Ω
H23-5 (E) - Body ground Always Below 1 Ω
H23-2 (LP) or A-23 (IND) - Body ground Always 10 kΩ or higher




OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR