Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › THEFT DETERRENT SYSTEM › 2015.06–2017.08
RM27T0E _58 Vehicle Interior _053731 THEFT DETERRENT / KEYLESS ENTRY _0261054 THEFT DETERRENT SYSTEM C

THEFT DETERRENT / KEYLESS ENTRY  THEFT DETERRENT SYSTEM  B2762  Intrusion Sensor Signal Circuit Malfunction  B2764  Short to GND in Intrusion Sensor Signal Circuit  


DESCRIPTION

The theft warning radar sensor (intrusion sensor) conducts a self-diagnosis immediately after power is supplied to the sensor (when the theft deterrent system is set).

If a malfunction is detected in the IOUT line, the main body ECU stores DTC B2762.

DTC B2764 is stored when terminal IOUT of the theft warning radar sensor (intrusion sensor) has not received a signal for 5 seconds or more.

DTC Code DTC Detection Condition Trouble Area
B2762 After a normal/trouble signal is output from the theft warning radar sensor (intrusion sensor) as a result of self-diagnosis, either of the following malfunctions is detected:
1.

The IOUT line circuit is open.

2.

Signals other than a normal/trouble signal are received.


·

Map light assembly (theft warning radar sensor [intrusion sensor])

·

Main body ECU

·

Harness or connector


B2764 After a normal/trouble signal is output from the theft warning radar sensor (intrusion sensor) as a result of self-diagnosis, the following malfunction is detected:
Terminal IOUT of the theft warning radar sensor (intrusion sensor) has not received a signal for 5 seconds or more.
·

Map light assembly (theft warning radar sensor [intrusion sensor])

·

Main body ECU

·

Harness or connector



WIRING DIAGRAM

B240856E01
5.287,1.762 6.976,2.138 1.689,0.376 10 Main Body ECU (Multiplex Network Body ECU) 2.741,0.445 3.928,0.994 1.187,0.550 10 Theft Warning Radar Sensor (Intrusion Sensor) 2.683,2.091 4.010,2.287 1.328,0.197 10 Map Light Assembly 0.186,0.519 0.996,0.716 0.809,0.197 10 from Battery 2.683,1.92 2.927,2.116 0.244,0.197 10 W7 5.287,1.584 5.569,1.781 0.281,0.197 10 G63 5.264,0.666 5.457,0.821 0.192,0.155 10 12 4.545,0.666 4.738,0.821 0.192,0.155 10 6 5.536,0.767 5.833,0.922 0.297,0.155 10 ISIF 4.11,0.667 4.468,0.821 0.358,0.155 10 IOUT 2.062,0.413 2.254,0.568 0.192,0.155 10 7 2.243,0.413 2.601,0.568 0.358,0.155 10 S+B 2.062,1.238 2.254,1.393 0.192,0.155 10 5 2.211,1.239 2.650,1.394 0.439,0.155 10 GND3 1.412,0.666 1.885,0.839 0.473,0.174 10 ECU-B

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


PROCEDURE

1.CHECK HARNESS AND CONNECTOR (MAP LIGHT - BATTERY AND BODY GROUND)
a.
U170568E01
1.599,0.448 1.865,0.605 0.266,0.158 10 W7 0.121,0.77 0.558,0.928 0.437,0.158 10 GND3 0.75,0.453 1.062,0.611 0.312,0.158 10 S+B 0.1,0.095 0.398,0.253 0.298,0.158 10 *a 1.119,0.627 1.66,1.361 false 0.677,0.86 1.354,1.364 false

Disconnect the W7 light connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
W7-5 (GND3) - Body ground Always Below 1 Ω



c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
W7-7 (S+B) - Body ground Always 11 to 14 V



Text in Illustration
*a Front view of wire harness connector
(to Map Light Assembly)


OK

2.CHECK HARNESS AND CONNECTOR (MAP LIGHT - MAIN BODY ECU)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.CHECK HARNESS AND CONNECTOR (MAP LIGHT - MAIN BODY ECU)
a.

Disconnect the W7 light connector.


b.

Disconnect the G63 ECU connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
W7-6 (IOUT) - G63-12 (ISIF) Always Below 1 Ω
W7-6 (IOUT) or G63-12 (ISIF) - Body ground Always 10 kΩ or higher




OK

3.CHECK MAP LIGHT ASSEMBLY (THEFT WARNING RADAR SENSOR)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK MAP LIGHT ASSEMBLY (THEFT WARNING RADAR SENSOR)
a.

Using an oscilloscope, check the waveform.

B450007E01
1.438,0.313 1.865,0.635 0.427,0.323 1.865,1.479 2.302,2.083 true 4.74,1.938 4.958,2.5 4.958,2.5 5.115,2.5 true 1.531,0.406 1.844,0.604 0.313,0.198 10 false W7 0.302,0.302 0.615,0.5 0.313,0.198 10 false *a 3.875,0.417 4.188,0.615 0.313,0.198 10 false *b 2.281,2.146 2.896,2.344 0.615,0.198 10 false IOUT 6.448,1.906 7.063,2.104 0.615,0.198 10 false GND 4.104,1.271 4.417,1.469 0.313,0.198 10 false HI 3.906,1.865 4.365,2.063 0.458,0.198 10 false LOW 5.198,2.417 5.51,2.615 0.313,0.198 10 false *c

Measurement Condition
Item Content
Tester Connection W7-6 (IOUT) - Body ground
Tool Setting 2 V/DIV., 100 ms./DIV.
Condition Immediately after theft deterrent system set

HINT:
·

If the intrusion sensor is normal when the map light receives a HI input signal from the main body ECU, the sensor outputs the initial response.

·

When the input signal from the main body ECU is LOW and does not change, the main body ECU may be malfunctioning.



OK:

Initial response occurs (refer to illustration).


Text in Illustration
*a Component with harness connected
(Map Light Assembly)
*b Waveform
*c Initial Response

Result
Result Proceed to
OK A
NG (Signal is LOW and does not change) B
NG (Signal is HIGH and does not change) C



A

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

B

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

C

REPLACE MAP LIGHT ASSEMBLY (THEFT WARNING RADAR SENSOR)