Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › THEFT DETERRENT SYSTEM › 2015.06–2017.08
RM27T0E _58 Vehicle Interior _053731 THEFT DETERRENT / KEYLESS ENTRY _0261054 THEFT DETERRENT SYSTEM J

THEFT DETERRENT / KEYLESS ENTRY  THEFT DETERRENT SYSTEM  Intrusion Sensor Cancel Switch Circuit  


DESCRIPTION

When the intrusion sensor OFF switch on the map light assembly is pressed, the sensor off signal is sent to the main body ECU which causes the theft warning radar sensor (intrusion sensor) to stop operating.


WIRING DIAGRAM

B246189E01
4.957,1.822 6.643,2.165 1.686,0.342 10 Main Body ECU (Multiplex Network Body ECU) 5.044,0.751 5.244,0.921 0.200,0.170 10 23 5.348,0.849 5.837,1.032 0.489,0.184 10 SSW1 1.186,0.751 1.386,0.921 0.200,0.170 10 5 1.378,0.849 1.813,1.032 0.435,0.184 10 GND3 2.455,0.742 2.654,0.912 0.199,0.170 10 26 1.941,0.849 2.382,1.032 0.441,0.184 10 SOFF 1.118,1.659 1.391,1.812 0.273,0.153 10 W7 1.118,1.823 3.246,2.165 2.128,0.342 10 Map Light Assembly (Intrusion Sensor OFF Switch) 4.957,1.659 5.323,1.800 0.366,0.141 10 G64

PROCEDURE

1.READ VALUE USING INTELLIGENT TESTER (INTRUSION SENSOR OFF SWITCH)
a.

Using the intelligent tester, read the Data List (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>THEFT DETERRENT SYSTEM>DATA LIST / ACTIVE TEST).

Main Body
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
Intrusion Sens OFF SW Intrusion sensor OFF switch /
ON or OFF
ON: Intrusion sensor OFF switch pushed
OFF: Intrusion sensor OFF switch not pushed
-

OK:

ON (intrusion sensor OFF switch pushed) and OFF (intrusion sensor OFF switch not pushed) appear on screen according to switch condition.




OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

2.INSPECT MAP LIGHT ASSEMBLY (INTRUSION SENSOR OFF SWITCH)
2.INSPECT MAP LIGHT ASSEMBLY (INTRUSION SENSOR OFF SWITCH)
a.
E140936E19
0.441,1.917 0.867,2.066 0.427,0.149 10 SOFF 2.395,0.619 2.822,0.768 0.427,0.149 10 GND3 0.948,1.998 1.063,1.998 1.063,1.998 1.15,1.607 false 2.343,0.709 2.227,0.709 2.227,0.709 2.098,1.352 false

Remove the map light (See page Vehicle Interior>LIGHTING (INT)>ROOM LIGHT(for Front)>REMOVAL).


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
5 (GND3) - 26 (SOFF) Intrusion sensor OFF switch pushed Below 1 Ω
5 (GND3) - 26 (SOFF) Intrusion sensor OFF switch not pushed 10 kΩ or higher




OK

3.CHECK HARNESS AND CONNECTOR (MAP LIGHT - MAIN BODY ECU AND BODY GROUND)

NG

MAP LIGHT ASSEMBLY (INTRUSION SENSOR OFF SWITCH)

3.CHECK HARNESS AND CONNECTOR (MAP LIGHT - MAIN BODY ECU AND BODY GROUND)
a.

Disconnect the W7 light connector.


b.

Disconnect the G64 ECU connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
W7-26 (SOFF) - G64-23 (SSW1) Always Below 1 Ω
W7-26 (SOFF) or G64-23 (SSW1) - Body ground Always 10 kΩ or higher
W7-5 (GND3) - Body ground Always Below 1 Ω




OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR