Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › ENGINE IMMOBILISER SYSTEM(w/o Entry and Start System)
RM27T0E _58 Vehicle Interior _053731 THEFT DETERRENT / KEYLESS ENTRY _0261067 ENGINE IMMOBILISER SYSTEM(w/o Entry and Start System) C

THEFT DETERRENT / KEYLESS ENTRY  ENGINE IMMOBILISER SYSTEM(w/o Entry and Start System)  B2780  Push Switch / Key Unlock Warning Switch Malfunction  


DESCRIPTION

This DTC is stored if the transponder key ECU assembly does not detect that the unlock warning switch assembly is on even when the ignition switch is ON.

DTC No. DTC Detection Condition Trouble Area DTC Output Confirmation Operation
B2780 The unlock warning switch assembly is not detected as being on when the ignition switch is ON (1 trip detection logic*).
·

Harness or connector

·

Unlock warning switch assembly

·

Transponder key ECU assembly


Insert the key into the ignition key cylinder.

*: Only output while a malfunction is present.


Vehicle Condition and Fail-safe Operation when Malfunction Detected
Vehicle Condition when Malfunction Detected Fail-safe Operation when Malfunction Detected
Engine cannot be started -

Related Data List and Active Test
DTC No. Data List and Active Test
B2780 Key SW

WIRING DIAGRAM

B278950E33
2.167,1.094 4.292,1.448 2.125,0.354 10 false Unlock Warning Switch Assembly 2.167,0.885 2.479,1.125 0.313,0.24 10 false G3 5.375,1.833 6.76,2.365 1.385,0.531 10 false Transponder Key ECU Assembly 5.375,1.656 5.781,1.823 0.406,0.167 10 false G74 5.646,0.542 6,0.698 0.354,0.156 10 false KSW 5.479,0.469 5.604,0.625 0.125,0.156 10 false 3 3.74,0.458 3.865,0.615 0.125,0.156 10 false 1 2.5,0.458 2.625,0.615 0.125,0.156 10 false 2

CAUTION / NOTICE / HINT

NOTICE:
·

If the transponder key ECU assembly is replaced, refer to the Service Bulletin.

·

After repair, confirm that no DTCs are output by performing "DTC Output Confirmation Operation".

·

When using the GTS with the vehicle ignition switch off, connect the GTS to the vehicle and turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the GTS and the vehicle begins. Then select the Model Code "KEY REGIST" under manual mode and enter the following menus: Body Electrical / Immobiliser. While using the GTS, periodically turn a courtesy light switch on and off at intervals of 1.5 seconds or less to maintain communication between the GTS and the vehicle.



PROCEDURE

2.CHECK FOR DTC
a.

Check for DTCs (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENGINE IMMOBILISER SYSTEM(w/o Entry and Start System)>DTC CHECK / CLEAR).

HINT:

Before checking for DTCs, perform the "DTC Output Confirmation Operation" procedure.


OK:

DTC B2780 is not output.




OK

NG

3.INSPECT UNLOCK WARNING SWITCH ASSEMBLY
3.INSPECT UNLOCK WARNING SWITCH ASSEMBLY
a.

Remove the unlock warning switch assembly (See page Vehicle Interior>DOOR LOCK>UNLOCK WARNING SWITCH>REMOVAL).


b.

Inspect the unlock warning switch assembly (See page Vehicle Interior>DOOR LOCK>UNLOCK WARNING SWITCH>INSPECTION).



OK

4.CHECK HARNESS AND CONNECTOR (UNLOCK WARNING SWITCH ASSEMBLY - TRANSPONDER KEY ECU ASSEMBLY AND BODY GROUND)

NG

REPLACE UNLOCK WARNING SWITCH ASSEMBLY

4.CHECK HARNESS AND CONNECTOR (UNLOCK WARNING SWITCH ASSEMBLY - TRANSPONDER KEY ECU ASSEMBLY AND BODY GROUND)
a.

Disconnect the G3 unlock warning switch assembly connector.


b.

Disconnect the G74 transponder key ECU assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G3-1 - G74-3 (KSW) Always Below 1 Ω
G3-2 - Body ground Always Below 1 Ω
G3-1 - Body ground Always 10 kΩ or higher
G74-3 (KSW) - Body ground Always 10 kΩ or higher




OK

REPLACE TRANSPONDER KEY ECU ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR