When a key is inserted into the ignition key cylinder, the transponder key coil receives the key ID code and sends it to the transponder key ECU assembly.
If an error in communication between the transponder key coil and transponder key ECU assembly occurs, this symptom may occur.
If the transponder key ECU assembly or key is replaced, refer to the Service Bulletin.
When using the GTS with the engine switch off to troubleshoot:
When using the GTS with the vehicle ignition switch off, connect the GTS to the vehicle and turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the GTS and the vehicle begins. Then select the Model Code "KEY REGIST" under manual mode and enter the following menus: Body Electrical / Immobiliser. While using the GTS, periodically turn a courtesy light switch on and off at intervals of 1.5 seconds or less to maintain communication between the GTS and the vehicle.
NEXT
Check for DTCs (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENGINE IMMOBILISER SYSTEM(w/o Entry and Start System)>DTC CHECK / CLEAR).
Before checking for DTCs, perform the "DTC Output Confirmation Operation" procedure.
| Result | Proceed to |
|---|---|
| DTCs are not output (for SFI System) | A |
| DTCs are not output (for ECD System) | B |
| DTCs are output | C |
A
B
C
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Body Electrical / Immobiliser or Main Body / Active Test.
Perform the Active Test according to the display on the GTS.
| Tester Display | Measurement Item / Range | Normal Condition | Diagnostic Note |
|---|---|---|---|
| Immobiliser Fuel Cut | Status of immobiliser system fuel cut / OFF/ON | ON: Immobiliser fuel cut on
OFF: Immobiliser fuel cut off |
- |
The item in the Data List indicates "OFF".
OK
(See pageEngine / Hybrid System>2TR-FE (ENGINE CONTROL)>SFI SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING)
NG
Check that the security indicator light turns off when a registered key is inserted into the ignition key cylinder.
Security indicator light turns off.
OK
NG
Check that the security indicator light turns off when another registered key is inserted into the ignition key cylinder.
Security indicator light turns off.
OK
NG
Using another registered key, turn the ignition switch to ON.
Check that the engine starts 5 seconds after the ignition switch was turned to ON.
Engine starts normally.
| Result | Proceed to |
|---|---|
| Engine can be started | A |
| Engine cannot be started | B |
A
B
Replace the key.
Key ID code registration is necessary when replacing the key.
Refer to the Service Bulletin.
NEXT
Using a registered key, turn the ignition switch to ON.
Check that the engine starts 5 seconds after the ignition switch was turned to ON.
Engine starts normally.
| Result | Proceed to |
|---|---|
| Engine can be started | A |
| Engine cannot be started (for 2TR-FE) | B |
| Engine cannot be started (for 1KD-FTV) | C |
| Engine cannot be started (for 5L-E) | D |
A
B
(See pageEngine / Hybrid System>2TR-FE (ENGINE CONTROL)>SFI SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING)
C
(See pageEngine / Hybrid System>1KD-FTV (ENGINE CONTROL)>ECD SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING)
D
(See pageEngine / Hybrid System>5L-E (ENGINE CONTROL)>ECD SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING)
Temporarily replace the transponder key coil with a new or known good one (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>TRANSPONDER KEY AMPLIFIER>REMOVAL).
NEXT
Using a registered key, turn the ignition switch to ON.
Check that the engine starts 5 seconds after the ignition switch was turned to ON.
Engine starts normally.
| Result | Proceed to |
|---|---|
| Engine can be started | A |
| Engine cannot be started | B |
A
B
Replace the transponder key ECU assembly with a new one.
Refer to the Service Bulletin.
Key ID code registration is necessary when replacing the transponder key ECU assembly.
Refer to the Service Bulletin.
NEXT
Using a registered key, turn the ignition switch to ON.
Check that the engine starts 5 seconds after the ignition switch was turned to ON.
Engine starts normally.
| Result | Proceed to |
|---|---|
| Engine can be started | A |
| Engine cannot be started | B |
A
B
Temporarily replace the key with a new or known good one.
Key ID code registration is necessary when replacing the key.
Refer to the Service Bulletin.
NEXT
Using a registered key, turn the ignition switch to ON.
Check that the engine starts 5 seconds after the ignition switch was turned to ON.
Engine starts normally.
| Result | Proceed to |
|---|---|
| Engine can be started | A |
| Engine cannot be started (for 2TR-FE) | B |
| Engine cannot be started (for 1KD-FTV) | C |
| Engine cannot be started (for 5L-E) | D |
A
B
(See pageEngine / Hybrid System>2TR-FE (ENGINE CONTROL)>SFI SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING)
C
(See pageEngine / Hybrid System>1KD-FTV (ENGINE CONTROL)>ECD SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING)
D
(See pageEngine / Hybrid System>5L-E (ENGINE CONTROL)>ECD SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING)