Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › AIRBAG SYSTEM › 2015.06–2017.08
RM27T0E _58 Vehicle Interior _053735 SUPPLEMENTAL RESTRAINT SYSTEMS _0261086 AIRBAG SYSTEM C

SUPPLEMENTAL RESTRAINT SYSTEMS  AIRBAG SYSTEM  B1651/33  Manual Cut off Switch Trouble  


DESCRIPTION

HINT:

"Manual cut off switch" refers to the airbag cutoff switch cylinder.


The airbag cutoff switch cylinder circuit consists of the center airbag sensor and airbag cutoff switch cylinder.

The instrument panel passenger airbag can be optionally deactivated via this circuit by turning the airbag cutoff switch cylinder to the "OFF" position.

If the instrument panel passenger airbag is deactivated, the airbag cutoff indicator comes on to inform the passengers.

DTC B1651/33 is stored when a malfunction is detected in the airbag cutoff switch cylinder circuit.

DTC Code DTC Detection Condition Trouble Area
B1651/33 One of the following conditions is met:
·

The center airbag sensor detects a line short circuit signal, open circuit signal, short circuit to ground signal or short circuit to B+ signal in the airbag cutoff switch cylinder circuit for 2 seconds.

·

An airbag cutoff switch cylinder malfunction.

·

A center airbag sensor malfunction.


·

Instrument panel wire

·

Airbag cutoff switch cylinder sub-assembly

·

Center airbag sensor assembly



WIRING DIAGRAM

C199310E04
0.626,3.233 2.570,3.403 1.943,0.170 10 Airbag Cutoff Switch Cylinder 0.626,3.026 0.993,3.182 0.367,0.155 10 G73 5.482,3.233 6.873,3.403 1.390,0.170 10 Center Airbag Sensor 5.482,3.026 5.849,3.182 0.367,0.155 10 G1 5.854,1.144 6.320,1.321 0.466,0.177 10 MSW+ 5.854,2.335 6.320,2.512 0.466,0.177 10 MSW- 5.517,2.219 5.728,2.389 0.211,0.170 10 12 5.517,0.994 5.728,1.164 0.211,0.170 10 11 2.102,1.025 2.568,1.202 0.466,0.177 10 PMC+ 2.102,2.216 2.568,2.393 0.466,0.177 10 PMC- 2.62,2.219 2.790,2.389 0.170,0.170 10 1 2.62,0.994 2.790,1.164 0.170,0.170 10 2

CAUTION / NOTICE / HINT

NOTICE:
·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).

·

When disconnecting the cable from the negative (-) battery terminal while performing repairs, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).



HINT:

The 19-11 (MSW+) and 19-12 (MSW-) terminals in this circuit have an activation prevention mechanism. This mechanism can be used to check for an open circuit in the wire harness. In case of other checks (check for short, short to ground or short to B+), it is necessary to release this mechanism.


PROCEDURE

1.CHECK INSTRUMENT PANEL WIRE (CENTER AIRBAG SENSOR - AIRBAG CUTOFF SWITCH CYLINDER)
a.
U169940E02
1.177,4.083 2.208,3.563 false 2.344,3.552 2.646,4.094 false 1.604,2.323 1.115,2.688 false 1.948,2.302 2.385,2.667 false 0.76,1.094 1.01,1.25 0.25,0.156 10 false *1 2.271,1.458 2.521,1.615 0.25,0.156 10 false *2 2.198,0.542 2.365,0.708 0.167,0.167 10 false A 1.021,0.542 1.188,0.708 0.167,0.167 10 false D 1.406,0.813 1.573,0.979 0.167,0.167 10 false C 1.813,0.792 1.979,0.958 0.167,0.167 10 false B 0.594,2.938 0.844,3.094 0.25,0.156 10 false *5 0.594,1.74 0.844,1.896 0.25,0.156 10 false *3 2.656,3.49 2.906,3.646 0.25,0.156 10 false *6 2.417,2.073 2.667,2.229 0.25,0.156 10 false *4 0.615,3.427 0.823,3.573 0.208,0.146 10 false G1 0.563,2.177 0.854,2.323 0.292,0.146 10 false G73 2.646,4.094 3.125,4.271 0.479,0.177 10 false MSW+ 0.729,4.01 1.271,4.188 0.542,0.177 10 false MSW- 2.479,2.604 2.917,2.781 0.438,0.177 10 false PMC+ 0.677,2.635 1.104,2.813 0.427,0.177 10 false PMC-

Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


c.

Disconnect the connectors from the center airbag sensor and airbag cut off switch cylinder.


d.

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.


e.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
G73-2 (PMC+) - Body ground Ignition switch ON Below 1 V
G73-1 (PMC-) - Body ground Ignition switch ON Below 1 V



f.

Turn the ignition switch off.


g.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


h.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G73-2 (PMC+) - G73-1 (PMC-) Always Below 1 Ω



i.

Release the activation prevention mechanism built into connector B (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DIAGNOSIS SYSTEM).


j.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G73-2 (PMC+) - G73-1 (PMC-) Always 1 MΩ or higher
G73-2 (PMC+) - Body ground Always 1 MΩ or higher
G73-1 (PMC-) - Body ground Always 1 MΩ or higher



Text in Illustration
*1 Airbag Cutoff Switch Cylinder
*2 Center Airbag Sensor
*3 Front view of wire harness connector
(to Airbag Cutoff Switch Cylinder)
*4 Connector C
*5 Rear view of wire harness connector
(to Center Airbag Sensor)
*6 Connector B


OK

2.INSPECT AIRBAG CUTOFF SWITCH CYLINDER

NG

REPLACE INSTRUMENT PANEL WIRE

2.INSPECT AIRBAG CUTOFF SWITCH CYLINDER
a.
C198536E02
1.037,1.598 1.498,1.796 0.461,0.198 10 PMC+ 1.884,1.581 2.304,1.778 0.420,0.198 10 PMC- 1.569,1.3 1.317,1.581 false 1.839,1.3 2.056,1.587 false

Remove the airbag cutoff switch cylinder (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG CUT-OFF SWITCH>REMOVAL).


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
2 (PMC+) - 1 (PMC-) Cutoff switch in "ON" position (Front passenger side airbag active) 360 to 440 Ω
2 (PMC+) - 1 (PMC-) Cutoff switch in "OFF" position (Front passenger side airbag not active) 90 to 110 Ω




OK

3.CHECK CENTER AIRBAG SENSOR

NG

REPLACE AIRBAG CUTOFF SWITCH CYLINDER SUB-ASSEMBLY

3.CHECK CENTER AIRBAG SENSOR
a.
C201187E01
0.756,1.333 0.953,1.530 0.198,0.198 10 *1 1.787,1.676 1.985,1.874 0.198,0.198 10 *2

Connect the connectors to the center airbag sensor and airbag cutoff switch cylinder.


b.

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.


c.

Turn the ignition switch to ON, and wait for at least 60 seconds.



e.

Turn the ignition switch off.


f.

Turn the ignition switch to ON, and wait for at least 60 seconds.


g.

Check for DTCs (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR).

OK:

DTC B1651 is not output.


HINT:

Codes other than DTC B1651 may be output at this time, but they are not related to this check.


Text in Illustration
*1 Airbag Cutoff Switch Cylinder
*2 Center Airbag Sensor



OK

NG