Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › AIRBAG SYSTEM › 2015.06–2017.08
RM27T0E _58 Vehicle Interior _053735 SUPPLEMENTAL RESTRAINT SYSTEMS _0261086 AIRBAG SYSTEM C

SUPPLEMENTAL RESTRAINT SYSTEMS  AIRBAG SYSTEM  B1612/83  Lost Communication with Front Airbag Sensor RH  B1613/83  Front Airbag Sensor RH Initialization Incomplete  


DESCRIPTION

The front airbag sensor RH circuit consists of the center airbag sensor and front airbag sensor RH.

The front airbag sensor RH detects impacts to the vehicle and sends signals to the center airbag sensor to determine if the airbag should be deployed.

DTC B1612/83 or B1613/83 is stored when a malfunction is detected in the front airbag sensor RH circuit.

DTC Code DTC Detection Condition Trouble Area
B1612/83 One of the following conditions is met:
·

The center airbag sensor detects a line short circuit signal, open circuit signal, short circuit to ground signal or short circuit to B+ signal in the front airbag sensor RH circuit for 2 seconds.

·

A front airbag sensor RH malfunction.

·

A center airbag sensor malfunction.


·

Instrument panel wire

·

Engine room main wire

·

Front airbag sensor RH

·

Center airbag sensor assembly


B1613/83 One of the following conditions is met:
·

The center airbag sensor detects a line short circuit signal, open circuit signal, short circuit to ground signal or short circuit to B+ signal in the front airbag sensor RH circuit for 2 seconds.

·

A front airbag sensor RH malfunction.

·

A center airbag sensor malfunction.


·

Instrument panel wire

·

Engine room main wire

·

Front airbag sensor RH

·

Center airbag sensor assembly



WIRING DIAGRAM

C213916E03
5.584,3.826 5.886,3.997 0.302,0.171 10 G1 0.438,3.858 0.740,4.029 0.302,0.171 10 A20 3.591,2.172 3.891,2.343 0.300,0.171 10 GA5 3.591,0.995 3.891,1.166 0.300,0.171 10 GA5 1.717,0.889 2.018,1.060 0.302,0.171 10 2 1.717,2.073 2.018,2.244 0.302,0.171 10 1 5.31,0.889 5.612,1.060 0.302,0.171 10 29 5.31,2.073 5.612,2.244 0.302,0.171 10 27 3.697,0.798 3.795,0.969 0.098,0.171 10 1 3.697,1.982 3.795,2.153 0.098,0.171 10 2 5.622,0.994 5.923,1.165 0.302,0.171 10 +SR 5.622,2.161 5.923,2.332 0.302,0.171 10 -SR 1.292,0.994 1.594,1.165 0.302,0.171 10 +SR 1.292,2.161 1.594,2.332 0.302,0.171 10 -SR 0.438,4.012 2.003,4.185 1.566,0.173 10 Front Airbag Sensor RH 5.584,3.998 6.974,4.196 1.390,0.198 10 Center Airbag Sensor

CAUTION / NOTICE / HINT

NOTICE:
·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).

·

When disconnecting the cable from the negative (-) battery terminal while performing repairs, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).



PROCEDURE

1.CHECK CONNECTION OF CONNECTORS
a.

Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


c.

Check that the connectors are properly connected to the center airbag sensor and front airbag sensor RH.

OK:

The connectors are properly connected.




OK

2.CHECK CONNECTORS

NG

CONNECT CONNECTORS PROPERLY

2.CHECK CONNECTORS
a.

Disconnect the connectors from the center airbag sensor and front airbag sensor RH.


b.
C213959E01
0.344,1.175 0.514,1.345 0.170,0.170 10 *1 2.2,1.57 2.370,1.740 0.170,0.170 10 *2

Check that the connectors (on the center airbag sensor side and front airbag sensor RH side) are not damaged.

OK:

The connectors are not deformed or damaged.


Text in Illustration
*1 Front Airbag Sensor RH
*2 Center Airbag Sensor



OK

3.CHECK FRONT AIRBAG SENSOR RH CIRCUIT

NG

REPLACE HARNESS AND CONNECTOR

3.CHECK FRONT AIRBAG SENSOR RH CIRCUIT
a.

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.

U148405E01
0.279,0.974 0.463,1.148 0.184,0.174 10 *1 1.456,1.196 1.630,1.375 0.175,0.179 10 *2 3.502,0.072 3.686,0.247 0.184,0.174 10 *a 4.196,0.707 4.370,0.886 0.175,0.179 10 *3 5.491,1.495 5.666,1.674 0.175,0.179 10 *5 5.937,0.082 6.121,0.256 0.184,0.174 10 *b 6.75,0.707 6.924,0.886 0.175,0.179 10 *4 0.424,0.522 0.598,0.715 0.174,0.193 10 F 0.691,0.718 0.912,0.976 0.221,0.258 10 E 0.938,0.718 1.131,0.958 0.193,0.239 10 D 1.05,0.718 1.261,0.939 0.211,0.221 10 C 1.296,0.718 1.507,0.948 0.211,0.230 10 B 1.575,0.522 1.768,0.706 0.193,0.184 10 A 2.532,0.465 2.805,0.649 0.273,0.184 10 A20 4.998,0.456 5.218,0.621 0.221,0.165 10 G1 2.908,1.368 3.221,1.533 0.313,0.165 10 -SR 4.043,1.373 4.356,1.538 0.313,0.165 10 +SR 6.614,1.293 6.927,1.458 0.313,0.165 10 -SR 4.895,1.078 5.209,1.244 0.313,0.165 10 +SR 3.52,0.794 3.114,1.34 false 3.693,0.798 4.132,1.363 false 5.73,0.89 5.217,1.142 false 5.945,0.889 6.585,1.318 false 5.671,1.285 5.591,1.48 false

Text in Illustration
*1 Front Airbag Sensor RH *2 Center Airbag Sensor
*3 Connector E *4 Connector B
*5 Service Wire - -
*a Front view of wire harness connector
(to Front Airbag Sensor RH)
*b Rear view of wire harness connector
(to Center Airbag Sensor)


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
A20-2 (+SR) - Body ground Ignition switch ON Below 1 V
A20-1 (-SR) - Body ground Ignition switch ON Below 1 V



c.

Turn the ignition switch off.


d.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


e.

Using a service wire, connect terminals 29 (+SR) and 27 (-SR) of connector B.

NOTICE:

Do not forcibly insert the service wire into the terminals of the connector when connecting a service wire.



f.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A20-2 (+SR) - A20-1 (-SR) Always Below 1 Ω



g.

Disconnect the service wire from connector B.


h.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A20-2 (+SR) - A20-1 (-SR) Always 1 MΩ or higher
A20-2 (+SR) - Body ground Always 1 MΩ or higher
A20-1 (-SR) - Body ground Always 1 MΩ or higher




OK

4.CHECK FRONT AIRBAG SENSOR RH

NG

5.CHECK INSTRUMENT PANEL WIRE (CENTER AIRBAG SENSOR - ENGINE ROOM MAIN WIRE)
4.CHECK FRONT AIRBAG SENSOR RH
a.
C171014E09
0.521,0.865 0.719,1.063 0.198,0.198 10 false *1 1.948,1.229 2.146,1.427 0.198,0.198 10 false *2

Connect the connectors to the center airbag sensor.


b.

Interchange the front airbag sensor LH with RH and connect the connectors to them.


c.

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.


d.

Turn the ignition switch to ON, and wait for at least 60 seconds.



f.

Turn the ignition switch off.


g.

Turn the ignition switch to ON, and wait for at least 60 seconds.


h.

Check for DTCs (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR).

Result
Result Proceed to
DTC B1612, B1613, B1617 and B1618 are not output A
DTC B1617 or B1618 is output B
DTC B1612 or B1613 is output C

HINT:

Codes other than DTC B1612, B1613, B1617 and B1618 may be output at this time, but they are not related to this check.


Text in Illustration
*1 Front Airbag Sensor LH
*2 Center Airbag Sensor



C

A

B

5.CHECK INSTRUMENT PANEL WIRE (CENTER AIRBAG SENSOR - ENGINE ROOM MAIN WIRE)
a.

Disconnect the instrument panel wire connector from the engine room main wire.

U148406E01
0.111,0.885 0.294,1.060 0.184,0.174 10 *1 1.054,0.021 1.238,0.196 0.184,0.174 10 *3 0.956,0.96 1.140,1.134 0.184,0.174 10 *4 1.568,1.126 1.742,1.305 0.175,0.179 10 *2 3.502,0.073 3.686,0.247 0.184,0.174 10 *a 4.364,0.585 4.538,0.764 0.175,0.179 10 *5 5.485,1.537 5.660,1.716 0.175,0.179 10 *7 5.956,0.073 6.140,0.247 0.184,0.174 10 *b 6.862,0.585 7.036,0.764 0.175,0.179 10 *6 0.961,0.654 1.164,0.819 0.202,0.165 10 D 1.12,0.654 1.378,0.875 0.258,0.221 10 C 1.4,0.654 1.575,0.838 0.174,0.184 10 B 1.662,0.486 1.827,0.716 0.165,0.230 10 A 0.7,0.654 0.967,0.921 0.267,0.267 10 E 0.429,0.486 0.724,0.781 0.295,0.295 10 F 0.868,0.505 0.868,0.079 0.868,0.079 1.027,0.079 false 1.3,0.599 1.3,1.025 1.3,1.025 1.141,1.025 false 2.723,0.557 3.060,0.731 0.336,0.174 10 GA5 4.948,0.554 5.187,0.710 0.239,0.156 10 G1 4.128,1.458 4.432,1.641 0.304,0.184 10 -SR 2.83,1.433 3.134,1.617 0.304,0.184 10 +SR 6.356,1.229 6.660,1.413 0.304,0.184 10 -SR 4.964,1.173 5.268,1.357 0.304,0.184 10 +SR 3.509,0.98 3.057,1.412 false 3.705,0.991 4.187,1.451 false 5.696,0.914 5.262,1.212 false 5.885,0.907 6.34,1.271 false 5.682,1.299 5.601,1.492 false

Text in Illustration
*1 Front Airbag Sensor RH *2 Center Airbag Sensor
*3 Engine Room Main Wire *4 Instrument Panel Wire
*5 Connector C *6 Connector B
*7 Service Wire - -
*a Front view of wire harness connector
(to Engine Room Main Wire)
*b Rear view of wire harness connector
(to Center Airbag Sensor)


b.

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
GA5-1 (+SR) - Body ground Ignition switch ON Below 1 V
GA5-2 (-SR) - Body ground Ignition switch ON Below 1 V



d.

Turn the ignition switch off.


e.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


f.

Using a service wire, connect terminals 29 (+SR) and 27 (-SR) of connector B.

NOTICE:

Do not forcibly insert the service wire into the terminals of the connector when connecting a service wire.



g.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
GA5-1 (+SR) - GA5-2 (-SR) Always Below 1 Ω



h.

Disconnect the service wire from connector B.


i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
GA5-1 (+SR) - GA5-2 (-SR) Always 1 MΩ or higher
GA5-1 (+SR) - Body ground Always 1 MΩ or higher
GA5-2 (-SR) - Body ground Always 1 MΩ or higher




OK

REPLACE ENGINE ROOM MAIN WIRE

NG

REPLACE INSTRUMENT PANEL WIRE