Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › AIRBAG SYSTEM › 2015.06–2017.08
RM27T0E _58 Vehicle Interior _053735 SUPPLEMENTAL RESTRAINT SYSTEMS _0261086 AIRBAG SYSTEM C

SUPPLEMENTAL RESTRAINT SYSTEMS  AIRBAG SYSTEM  B1610/13  Front Airbag Sensor RH Malfunction  


DESCRIPTION

The front airbag sensor RH consists of the diagnostic circuit and frontal deceleration sensor, etc.

If the center airbag sensor receives signals from the frontal deceleration sensor, it determines whether the SRS should be activated.

DTC B1610/13 is stored when a malfunction is detected in the front airbag sensor RH circuit.

DTC Code DTC Detection Condition Trouble Area
B1610/13 Either condition is met:
·

A front airbag sensor RH malfunction.

·

A center airbag sensor malfunction.


·

Front airbag sensor RH

·

Center airbag sensor assembly



WIRING DIAGRAM

C213916E03
5.584,3.826 5.886,3.997 0.302,0.171 10 G1 0.438,3.858 0.740,4.029 0.302,0.171 10 A20 3.591,2.172 3.891,2.343 0.300,0.171 10 GA5 3.591,0.995 3.891,1.166 0.300,0.171 10 GA5 1.717,0.889 2.018,1.060 0.302,0.171 10 2 1.717,2.073 2.018,2.244 0.302,0.171 10 1 5.31,0.889 5.612,1.060 0.302,0.171 10 29 5.31,2.073 5.612,2.244 0.302,0.171 10 27 3.697,0.798 3.795,0.969 0.098,0.171 10 1 3.697,1.982 3.795,2.153 0.098,0.171 10 2 5.622,0.994 5.923,1.165 0.302,0.171 10 +SR 5.622,2.161 5.923,2.332 0.302,0.171 10 -SR 1.292,0.994 1.594,1.165 0.302,0.171 10 +SR 1.292,2.161 1.594,2.332 0.302,0.171 10 -SR 0.438,4.012 2.003,4.185 1.566,0.173 10 Front Airbag Sensor RH 5.584,3.998 6.974,4.196 1.390,0.198 10 Center Airbag Sensor

CAUTION / NOTICE / HINT

NOTICE:
·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).

·

When disconnecting the cable from the negative (-) battery terminal while performing repairs, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).



PROCEDURE

1.CHECK FRONT AIRBAG SENSOR RH
C171014E08
0.521,0.865 0.719,1.063 0.198,0.198 10 false *1 1.948,1.25 2.146,1.448 0.198,0.198 10 false *2

a.

Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


c.

Interchange the front airbag sensor LH with RH and connect the connectors to them.


d.

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.


e.

Turn the ignition switch to ON, and wait for at least 60 seconds.



g.

Turn the ignition switch off.


h.

Turn the ignition switch to ON, and wait for at least 60 seconds.


i.

Check for DTCs (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR).

Result
Result Proceed to
DTC B1610 is output A
DTC B1615 is output B
DTC B1610 and B1615 are not output C

HINT:

Codes other than DTC B1610 and B1615 may be output at this time, but they are not related to this check.


Text in Illustration
*1 Front Airbag Sensor LH
*2 Center Airbag Sensor



C

A

B