Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › SPIRAL CABLE › 2015.06–2017.08
RM27T0E _58 Vehicle Interior _053735 SUPPLEMENTAL RESTRAINT SYSTEMS _0261087 SPIRAL CABLE A

SUPPLEMENTAL RESTRAINT SYSTEMS  SPIRAL CABLE  INSTALLATION  


CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for RHD and LHD vehicles.

·

The procedure listed below is for LHD vehicles.



PROCEDURE

Hide 84306 1.INSTALL SPIRAL CABLE SUB-ASSEMBLY

a.

Check that the ignition switch is off.


b.

Check that the cable is disconnected from the negative (-) battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.



c.

Attach the 3 claws to install the spiral cable sub-assembly.

CAUTION:

When replacing the spiral cable sub-assembly with a new one, remove the lock pin before installing the steering wheel assembly.



d.

Connect the connectors to the spiral cable sub-assembly.

NOTICE:

When handling the airbag connector, take care not to damage the airbag wire harness.



Hide 45286B 2.INSTALL UPPER STEERING COLUMN COVER

a.

for Manual Tilt and Manual Telescopic Steering Column:



b.

for Power Tilt and Power Telescopic Steering Column:



Hide 45287 3.INSTALL LOWER STEERING COLUMN COVER

a.

for Manual Tilt and Manual Telescopic Steering Column:



b.

for Power Tilt and Power Telescopic Steering Column:



Hide 4. TURN FRONT WHEELS TO FACE STRAIGHT AHEAD

Hide 84306 5.ADJUST SPIRAL CABLE SUB-ASSEMBLY

a.

Check the check window shown in the illustration.

HINT:

When the spiral cable sub-assembly is centered, the connector is at the top and the conditions below can be checked.


·

w/o Steering Heater:

With the steering wheel straight ahead, align the matchmarks to check the colored roller from the check window.

·

w/ Steering Heater:

With the steering wheel straight ahead, align the matchmarks to check the U-turn point of the cable from the check window.


B399753E07
1.573,1.073 1.094,1.073 true 1.219,2.688 1.344,2.688 1.344,2.688 1.344,3.229 true 1.229,2.76 1.344,2.76 false 4.188,2.427 4.188,2.781 true 4.01,2.594 4.188,2.594 true 5.948,2.781 5.948,3.125 true 5.771,2.938 5.948,2.938 true 5.677,1.167 6.104,1.167 true 0.938,0.99 1.125,1.167 0.188,0.177 10 false *a 6.135,1.094 6.323,1.271 0.188,0.177 10 false *a 0.167,0.063 0.396,0.24 0.229,0.177 10 false *A 3.281,0.063 3.51,0.24 0.229,0.177 10 false *B 3.646,1.719 3.875,1.896 0.229,0.177 10 false *C 5.375,2.063 5.604,2.24 0.229,0.177 10 false *D 1.281,3.219 1.469,3.396 0.188,0.177 10 false *b 4.125,2.802 4.313,2.979 0.188,0.177 10 false *b 5.885,3.135 6.073,3.313 0.188,0.177 10 false *b

Text in Illustration
*A w/o Steering Heater *B w/ Steering Heater
*C for Type A *D for Type B
*a Check Window *b Matchmark
V100155

Colored Roller
V100145

U-turn Point


b.

If the spiral cable sub-assembly is not centered, center it.


c.
C107193

Rotate the spiral cable sub-assembly counterclockwise slowly by hand until it stops.

CAUTION:

Do not turn the spiral cable sub-assembly using the airbag wire harness.



d.

Rotate the spiral cable sub-assembly 2.5 times clockwise from the lock position to align the matchmarks and check the check window.

HINT:
·

The spiral cable sub-assembly will rotate approximately 2.5 turns to both the left and right from the center.

·

When the spiral cable sub-assembly is centered, the connector is at the top and the conditions below can be checked.


·

w/o Steering Heater:

With the steering wheel straight ahead, align the matchmarks to check the colored roller from the check window.

·

w/ Steering Heater:

With the steering wheel straight ahead, align the matchmarks to check the U-turn point of the cable from the check window.



B400826E07
1.552,1.073 1.083,1.073 true 1.219,2.698 1.333,2.698 1.333,2.698 1.333,3.24 true 1.219,2.802 1.333,2.802 false 4.198,2.427 4.198,2.781 true 4.021,2.594 4.198,2.594 true 5.938,2.76 5.938,3.104 true 5.76,2.938 5.938,2.938 true 5.667,1.177 6.198,1.177 true 0.917,0.979 1.104,1.156 0.188,0.177 10 false *a 6.25,1.104 6.438,1.281 0.188,0.177 10 false *a 0.042,0.01 0.271,0.188 0.229,0.177 10 false *A 3.167,0.01 3.396,0.188 0.229,0.177 10 false *B 3.646,1.719 3.875,1.896 0.229,0.177 10 false *C 5.375,2.042 5.604,2.219 0.229,0.177 10 false *D 1.271,3.219 1.458,3.396 0.188,0.177 10 false *b 4.125,2.802 4.313,2.979 0.188,0.177 10 false *b 5.875,3.135 6.063,3.313 0.188,0.177 10 false *b

Text in Illustration
*A w/o Steering Heater *B w/ Steering Heater
*C for Type A *D for Type B
*a Check Window *b Matchmark
V100155

Colored Roller
V100145

U-turn Point

If the spiral cable sub-assembly cannot be centered, it is possible that the spiral cable sub-assembly is broken. Replace the spiral cable sub-assembly with a new one.


Hide 45100 6.INSTALL STEERING WHEEL ASSEMBLY

a.

Install the steering wheel assembly (See page Steering>STEERING COLUMN>STEERING WHEEL>INSTALLATION).