Home › Vehicle Interior › PRE-CRASH SAFETY › PRE-CRASH SAFETY SYSTEM › 2015.06–2017.08
RM27T0E _58 Vehicle Interior _053736 PRE-CRASH SAFETY _0261101 PRE-CRASH SAFETY SYSTEM C

PRE-CRASH SAFETY  PRE-CRASH SAFETY SYSTEM  B2002  Open in Seat Belt Motor RH Circuit  


DESCRIPTION

The seat belt control ECU receives collision information from the driving support ECU and skid control ECU via CAN communication and tightens the seat belt by operating the motor inside the front seat outer belt RH.

When DTC B2002 is stored, DTCs B2026 and B2027 are not stored.

DTC Code DTC Detection Condition Trouble Area
B2002 During the initial check or with the ignition switch ON, the seat belt motor RH circuit has an open (the voltage at terminal MOR+ is 8.5 V or higher and the voltage at terminal MOR- is below 2 V) for 1 second or more.
·

Front seat outer belt assembly RH

·

Harness or connector

·

Seat belt control ECU



WIRING DIAGRAM

E200776E19
5.552,3 6.958,3.188 1.406,0.188 10 false G117 5.563,3.198 6.958,3.427 1.396,0.229 10 false Seat Belt Control ECU 5.74,0.74 5.833,0.885 0.094,0.146 10 false 2 6.01,0.865 6.479,1.042 0.469,0.177 10 false MOR+ 6.01,2.313 6.448,2.51 0.438,0.198 10 false MOR- 5.74,2.198 5.833,2.344 0.094,0.146 10 false 1 2.458,0.74 2.896,0.938 0.438,0.198 10 false MOR+ 1.583,0.719 2.01,0.906 0.427,0.188 10 false MOR- 3.021,0.74 3.135,0.948 0.115,0.208 10 false 1 1.354,0.74 1.479,0.906 0.125,0.167 10 false 2 1.375,1.354 1.583,1.51 0.208,0.156 10 false Q3 1.365,1.51 3.594,1.906 2.229,0.396 10 false Front Seat Outer Belt Assembly RH (Seat Belt Motor RH)

CAUTION / NOTICE / HINT

CAUTION:

The pretensioner is built into the front seat outer belt assembly RH. Be sure to follow the correct inspection procedure, as failure to follow the correct procedure (such as inspection of incorrect connectors) may activate the pretensioner.


PROCEDURE

1.CHECK FRONT SEAT OUTER BELT ASSEMBLY RH CIRCUIT
a.
U170592E01
0.124,0.092 0.332,0.295 0.209,0.203 10 *a 1.507,0.345 1.866,0.485 0.358,0.139 10 G117 1.384,1.239 1.804,1.866 false 1.238,1.239 0.818,1.866 false 1.568,1.883 1.998,2.027 0.429,0.144 10 MOR+ 0.585,1.876 0.987,2.021 0.401,0.144 10 MOR-

Disconnect the G117 ECU connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G117-2 (MOR+) - G117-1 (MOR-) Always Below 20 Ω


Text in Illustration
*a Front view of wire harness connector
(to Seat Belt Control ECU)



OK

REPLACE SEAT BELT CONTROL ECU

NG

2.CHECK HARNESS AND CONNECTOR (SEAT BELT CONTROL ECU - FRONT SEAT OUTER BELT RH)
2.CHECK HARNESS AND CONNECTOR (SEAT BELT CONTROL ECU - FRONT SEAT OUTER BELT RH)
a.

Disconnect the G117 ECU connector.


b.

Disconnect the Q3 belt connector.


c.

Using a service wire, connect terminals Q3-1 (MOR+) and Q3-2 (MOR-) of the connector of the front seat outer belt RH.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G117-2 (MOR+) - G117-1 (MOR-) Always Below 2 Ω




OK

REPLACE FRONT SEAT OUTER BELT ASSEMBLY RH

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR