Home › Vehicle Interior › PRE-CRASH SAFETY › PRE-CRASH SAFETY SYSTEM › 2015.06–2017.08
RM27T0E _58 Vehicle Interior _053736 PRE-CRASH SAFETY _0261101 PRE-CRASH SAFETY SYSTEM C

PRE-CRASH SAFETY  PRE-CRASH SAFETY SYSTEM  B2007  Open in Seat Belt Motor LH Circuit  


DESCRIPTION

The seat belt control ECU receives collision information from the driving support ECU and skid control ECU via CAN communication and tightens the seat belt by operating the motor inside the front seat outer belt LH.

When DTC B2007 is stored, DTCs B2031 and B2032 are not stored.

DTC Code DTC Detection Condition Trouble Area
B2007 During the initial check or with the ignition switch ON, the seat belt motor LH circuit has an open (the voltage at terminal MOL+ is 8.5 V or higher and the voltage at terminal MOL- is below 2 V) for 1 second or more.
·

Front seat outer belt assembly LH

·

Harness or connector

·

Seat belt control ECU



WIRING DIAGRAM

E200776E20
5.552,3 6.958,3.188 1.406,0.188 10 false G117 5.563,3.198 6.958,3.427 1.396,0.229 10 false Seat Belt Control ECU 5.74,0.74 5.833,0.885 0.094,0.146 10 false 3 6.01,0.865 6.479,1.042 0.469,0.177 10 false MOL+ 6.01,2.313 6.448,2.51 0.438,0.198 10 false MOL- 5.74,2.198 5.833,2.344 0.094,0.146 10 false 4 2.458,0.74 2.896,0.938 0.438,0.198 10 false MOL+ 1.583,0.719 2.01,0.906 0.427,0.188 10 false MOL- 3.021,0.74 3.135,0.948 0.115,0.208 10 false 1 1.354,0.74 1.479,0.906 0.125,0.167 10 false 2 1.365,1.354 1.573,1.51 0.208,0.156 10 false R3 1.365,1.51 3.594,1.906 2.229,0.396 10 false Front Seat Outer Belt Assembly LH (Seat Belt Motor LH)

CAUTION / NOTICE / HINT

CAUTION:

The pretensioner is built into the front seat outer belt assembly LH. Be sure to follow the correct inspection procedure, as failure to follow the correct procedure (such as inspection of incorrect connectors) may activate the pretensioner.


PROCEDURE

1.CHECK FRONT SEAT OUTER BELT ASSEMBLY LH CIRCUIT
a.
U170593E01
1.475,0.374 1.836,0.525 0.360,0.151 10 G117 0.137,0.077 0.346,0.279 0.209,0.203 10 *a 2.203,1.239 2.623,1.866 false 2.058,1.239 1.637,1.866 false 2.388,1.883 2.817,2.027 0.429,0.144 10 MOL- 1.405,1.876 1.806,2.021 0.401,0.144 10 MOL+

Disconnect the G117 ECU connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G117-3 (MOL+) - G117-4 (MOL-) Always Below 20 Ω


Text in Illustration
*a Front view of wire harness connector
(to Seat Belt Control ECU)



OK

REPLACE SEAT BELT CONTROL ECU

NG

2.CHECK HARNESS AND CONNECTOR (FRONT SEAT OUTER BELT LH - SEAT BELT CONTROL ECU)
2.CHECK HARNESS AND CONNECTOR (FRONT SEAT OUTER BELT LH - SEAT BELT CONTROL ECU)
a.

Disconnect the G117 ECU connector.


b.

Disconnect the R3 belt connector.


c.

Using a service wire, connect terminals R3-1 (MOL+) and R3-2 (MOL-) of the connector of the front seat outer belt LH.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G117-3 (MOL+) - G117-4 (MOL-) Always Below 2 Ω




OK

REPLACE FRONT SEAT OUTER BELT ASSEMBLY LH

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR