Home › Vehicle Interior › PRE-CRASH SAFETY › PRE-CRASH SAFETY SYSTEM › 2015.06–2017.08
RM27T0E _58 Vehicle Interior _053736 PRE-CRASH SAFETY _0261101 PRE-CRASH SAFETY SYSTEM C

PRE-CRASH SAFETY  PRE-CRASH SAFETY SYSTEM  B2075  Passenger Side Seat Belt Buckle Switch Circuit Malfunction  


DESCRIPTION

This DTC is stored when there is a malfunction in the front seat inner belt buckle switch circuit for the passenger side. The seat belt control ECU receives buckle switch condition information from the front seat inner belt and controls the pre-crash safety system.

DTC Code DTC Detection Condition Trouble Area
B2075 A malfunction in the front seat inner belt (buckle switch) circuit.
·

Front seat inner belt assembly (for passenger side)

·

Harness or connector

·

Seat belt control ECU



WIRING DIAGRAM

E200777E01
0.102,2.998 0.814,3.151 0.711,0.152 10 *1: for LHD 0.102,3.31 0.848,3.463 0.746,0.152 10 *2: for RHD 3.597,1.211 3.748,1.353 0.151,0.142 10 *1 3.248,0.817 3.348,0.959 0.099,0.142 10 5 3.623,0.817 3.722,0.959 0.099,0.142 10 5 3.223,1.211 3.373,1.353 0.150,0.142 10 *2 3.155,2.088 3.429,2.230 0.274,0.142 10 R34 3.529,2.088 3.812,2.230 0.283,0.142 10 Q21 3.155,1.014 3.429,1.156 0.274,0.142 10 R34 3.529,1.014 3.812,1.156 0.283,0.142 10 Q21 3.597,2.293 3.748,2.435 0.151,0.142 10 *1 3.248,1.899 3.348,2.041 0.099,0.142 10 4 3.623,1.899 3.722,2.041 0.099,0.142 10 4 3.223,2.293 3.373,2.435 0.150,0.142 10 *2 2.518,0.747 3.064,1.057 0.546,0.310 10 RBE+*1 LBE+*2 2.578,2.197 3.064,2.507 0.486,0.310 10 RBE-*1 LBE-*2 1.059,2.736 3.015,3.062 1.956,0.326 10 Front Seat Inner Belt Assembly (for Passenger Side) 5.177,2.66 5.579,2.802 0.401,0.142 10 G118 5.399,2.09 5.800,2.232 0.401,0.142 10 PBK- 5.399,1.011 5.800,1.153 0.401,0.142 10 PBK+ 5.177,2.823 6.597,2.965 1.420,0.142 10 Seat Belt Control ECU 5.149,0.92 5.250,1.060 0.100,0.140 10 5 5.149,2.001 5.250,2.141 0.100,0.140 10 6

PROCEDURE

1.CHECK FOR DTC

OK

NG

2.CHECK SEAT BELT CONTROL ECU
2.CHECK SEAT BELT CONTROL ECU
a.

Remove the seat belt control ECU, but do not disconnect the connector (See page Vehicle Interior>PRE-CRASH SAFETY>SEAT BELT CONTROL ECU>REMOVAL).

U170646E01
0.048,0.042 2.378,0.355 2.330,0.313 10 Component with harness connected: (Seat Belt Control ECU) 2.448,1.626 2.598,2.278 2.598,2.278 2.686,2.278 false 2.384,1.626 2.234,2.278 2.234,2.278 2.146,2.278 false 2.701,2.211 3.082,2.357 0.382,0.145 10 PBK+ 1.786,2.211 2.167,2.357 0.382,0.145 10 PBK- 2.209,0.892 2.570,1.044 0.361,0.152 10 G118 4.735,1.464 5.064,1.608 0.329,0.144 10 GND 6.682,1.464 7.012,1.608 0.329,0.144 10 GND 3.158,0.539 4.666,0.679 1.508,0.140 10 Front seat belt fastened 5.111,0.553 6.896,0.693 1.786,0.140 10 Front seat belt unfastened


b.

Using an oscilloscope, check the waveform.

Measurement Condition
Item Content
Tester Connection G118-5 (PBK+) - G118-6 (PBK-)
Tool Setting 2 V/DIV., 20 ms/DIV.
Condition Ignition switch ON, front seat belt (for passenger side) fastened → unfastened

OK:

Waveform is as shown in illustration.




OK

REPLACE SEAT BELT CONTROL ECU

NG

3.CHECK HARNESS AND CONNECTOR (SEAT BELT CONTROL ECU - FRONT SEAT INNER BELT ASSEMBLY)
3.CHECK HARNESS AND CONNECTOR (SEAT BELT CONTROL ECU - FRONT SEAT INNER BELT ASSEMBLY)
a.

Disconnect the G118 ECU connector.


b.

Disconnect the Q21*1 or R34*2 belt connector.

*1: for LHD

*2: for RHD



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for LHD
Tester Connection Condition Specified Condition
G118-5 (PBK+) - Q21-5 (RBE+) Always Below 1 Ω
G118-6 (PBK-) - Q21-4 (RBE-)
G118-5 (PBK+) - Body ground Always 10 kΩ or higher
G118-6 (PBK-) - Body ground

for RHD
Tester Connection Condition Specified Condition
G118-5 (PBK+) - R34-5 (LBE+) Always Below 1 Ω
G118-6 (PBK-) - R34-4 (LBE-)
G118-5 (PBK+) - Body ground Always 10 kΩ or higher
G118-6 (PBK-) - Body ground




OK

REPLACE FRONT SEAT INNER BELT ASSEMBLY (for Passenger Side)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR