Home › Vehicle Interior › PRE-CRASH SAFETY › PRE-CRASH SAFETY SYSTEM › 2015.06–2017.08
RM27T0E _58 Vehicle Interior _053736 PRE-CRASH SAFETY _0261101 PRE-CRASH SAFETY SYSTEM J

PRE-CRASH SAFETY  PRE-CRASH SAFETY SYSTEM  Pre-crash Safety Brake Cancel Switch Circuit  


DESCRIPTION

The driving support ECU receives pre-crash brake on/off signals from the pre-crash brake cancel switch assembly.

WIRING DIAGRAM

E169489E29
5.028,2.039 6.258,2.195 1.230,0.156 10 G119 5.028,2.198 6.383,2.354 1.355,0.156 10 Driving Support ECU 2.329,1.152 2.818,1.308 0.489,0.156 10 G121 2.329,1.311 4.535,1.622 2.207,0.312 10 Pre-crash Brake Cancel Switch Assembly 4.979,0.722 5.091,0.878 0.112,0.156 10 5 3.2,0.722 3.376,0.878 0.177,0.156 10 2 2.849,0.928 3.166,1.084 0.317,0.156 10 ECU 2.401,0.928 2.734,1.084 0.333,0.156 10 GND 2.235,0.722 2.412,0.878 0.177,0.156 10 1 5.2,0.814 5.654,0.970 0.454,0.156 10 PBSW

PROCEDURE

1.READ VALUE USING INTELLIGENT TESTER
a.

Use the Data List to check if the pre-crash brake cancel switch assembly is functioning properly (See page Vehicle Interior>PRE-CRASH SAFETY>PRE-CRASH SAFETY SYSTEM>DATA LIST / ACTIVE TEST).

Pre-Crash 2
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
Pre-Crash Brake OFF Switch Pre-crash brake cancel switch assembly signal / ON or OFF ON: Pre-crash brake cancel switch assembly on
OFF: Pre-crash brake cancel switch assembly off
-

OK:

On screen, each item changes between ON and OFF according to above chart.




OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

2.INSPECT PRE-CRASH BRAKE CANCEL SWITCH ASSEMBLY
2.INSPECT PRE-CRASH BRAKE CANCEL SWITCH ASSEMBLY
a.
E118525E41
1.54,1.493 1.124,1.797 false 1.892,1.493 2.308,1.797 false 2.33,1.713 2.662,1.858 0.332,0.144 10 GND 0.732,1.713 1.052,1.858 0.320,0.144 10 ECU

Remove the pre-crash brake cancel switch assembly (See page Vehicle Interior>PRE-CRASH SAFETY>PRE-CRASH BRAKE CANCEL SWITCH>REMOVAL).


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
1 (GND) - 2 (ECU) Pressed Below 1 Ω
Not pressed 10 kΩ or higher




OK

3.CHECK HARNESS AND CONNECTOR (PRE-CRASH BRAKE CANCEL SWITCH - DRIVING SUPPORT ECU)

NG

REPLACE PRE-CRASH BRAKE CANCEL SWITCH ASSEMBLY

3.CHECK HARNESS AND CONNECTOR (PRE-CRASH BRAKE CANCEL SWITCH - DRIVING SUPPORT ECU)
a.

Disconnect the G121 switch connector.


b.

Disconnect the G119 ECU connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G121-2 (ECU) - G119-5 (PBSW) Always Below 1 Ω
G121-1 (GND) - Body ground
G121-2 (ECU) - Body ground Always 10 kΩ or higher




OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR