Home › Vehicle Interior › SEAT › REAR NO. 2 SEAT ASSEMBLY (for Power Seat Type LH Side) › 2015.06–2021.06
RM27T0E _58 Vehicle Interior _053737 SEAT _0261105 REAR NO. 2 SEAT ASSEMBLY(for Power Seat Type LH Side) A

SEAT  REAR NO. 2 SEAT ASSEMBLY(for Power Seat Type LH Side)  INSTALLATION  


CAUTION / NOTICE / HINT

CAUTION:

Wear protective gloves. Sharp areas on the parts may injure your hands.


NOTICE:
·

Under either of the following conditions, perform initialization (initial position memorization) of the fold seat control ECU (See page Vehicle Interior>SEAT>REAR POWER SEAT CONTROL SYSTEM>INITIALIZATION).

-

The fold seat control ECU is replaced with a new one.

-

Initialization (initial position reset) of the fold seat control ECU is performed.



·

Under any of the following conditions, perform initialization (initial position reset and initial position memorization) of the fold seat control ECU (See page Vehicle Interior>SEAT>REAR POWER SEAT CONTROL SYSTEM>INITIALIZATION).

-

The fold seat control ECU is exchanged with one from another vehicle.

-

The seatback frame and seat leg are inspected.

-

The seat is disassembled and the positions of the seatback and seat cushion change with respect to one another.

-

The seatback frame or seat leg is replaced.

-

The cable is disconnected from the battery while the seatback or seat cushion is operating.




HINT:
·

Use the same procedure for the RH and LH sides.

·

The procedure listed below is for the LH side.



PROCEDURE

Hide 1.INSTALL REAR NO. 2 SEAT ASSEMBLY LH

a.

Place the rear No. 2 seat assembly in the cabin.

NOTICE:

Be careful not to damage the vehicle body.


HINT:

If installing the seat on the RH side with the LH side installed, install it with the No. 3 rear seat leg cover LH raised.



b.

Temporarily install the 4 bolts.


c.

Tighten the 4 bolts.

Torque:
37 N*m (377 kgf*cm, 27 ft.*lbf)


d.
B238649E01
2.843,0.707 2.992,0.849 0.149,0.142 10 *1 2.917,1.295 2.917,0.874 false 1.081,1.534 1.230,1.676 0.149,0.142 10 *1 0.717,1.623 1.073,1.623 false

Attach the 6 claws and 2 guides to close the 2 covers.

Text in Illustration
*1 Guide


e.

Connect the connector.


Hide 58417D 2.INSTALL NO. 1 DECK BOARD BRACKET LH

a.

Install the bracket with the 2 bolts.


Hide 58439D 3.INSTALL DECK BOARD BRACKET REINFORCEMENT

a.

Attach the 2 hooks.


b.

Install the reinforcement with the 2 bolts.


Hide 58574A 4.INSTALL REAR FLOOR MAT SUPPORT PLATE

a.

Attach the 5 clips and 2 guides.


b.

Attach the 4 claws to install the plate.


c.

Install the 3 bolts.


Hide 58417 5.INSTALL REAR NO. 3 FLOOR BOARD (w/o Rear Air Conditioning System)

a.
B240100E01
0.785,2.139 0.934,2.277 0.149,0.137 10 *1 0.505,1.393 0.505,2.219 0.505,2.219 0.778,2.219 false 0.653,1.741 0.653,2.219 false

Attach the 2 guides and 4 claws.

Text in Illustration
*1 Guide


b.

Attach the clip to install the board.


Hide 58417 6.INSTALL REAR NO. 3 FLOOR BOARD (w/ Rear Air Conditioning System)

a.
B238653E01
0.365,1.798 0.518,1.943 0.152,0.145 10 *1 0.451,1.787 0.451,1.398 0.451,1.398 0.67,1.398 false 0.451,1.572 0.787,1.572 false

Attach the 2 guides and 3 claws.

Text in Illustration
*1 Guide


b.

Attach the clip to install the board.


Hide 58418A 7.INSTALL REAR NO. 4 FLOOR BOARD

a.
B238652E01
3.072,1.743 3.233,1.885 0.161,0.142 10 *1 2.958,1.542 2.958,1.815 2.958,1.815 3.064,1.815 false 2.958,1.815 2.875,1.815 false

Attach the 2 guides and 3 claws.

Text in Illustration
*1 Guide


b.

Attach the clip to install the board.


Hide 58410R 8.INSTALL DECK BOARD ASSEMBLY

a.

Attach the 4 clips.


b.

Install the deck board with the 2 bolts.


Hide 9.PERFORM INITIALIZATION

NOTICE:
·

Under either of the following conditions, perform initialization (initial position memorization) of the fold seat control ECU (See page Vehicle Interior>SEAT>REAR POWER SEAT CONTROL SYSTEM>INITIALIZATION).

-

The fold seat control ECU is replaced with a new one.

-

Initialization (initial position reset) of the fold seat control ECU is performed.



·

Under any of the following conditions, perform initialization (initial position reset and initial position memorization) of the fold seat control ECU (See page Vehicle Interior>SEAT>REAR POWER SEAT CONTROL SYSTEM>INITIALIZATION).

-

The fold seat control ECU is exchanged with one from another vehicle.

-

The seatback frame and seat leg are inspected.

-

The seat is disassembled and the positions of the seatback and seat cushion change with respect to one another.

-

The seatback frame or seat leg is replaced.

-

The cable is disconnected from the battery while the seatback or seat cushion is operating.




Hide 10.CHECK REAR NO. 2 SEAT

a.

Hide 11.ADJUST REAR SEAT LOCK CONTROL CABLE

a.
B505967C01
2.833,0.667 2.583,0.417 true 1.979,0.813 1.75,0.5 true 2,1.583 1.698,1.198 true 2.792,0.677 3.104,0.875 0.313,0.198 10 false *1 1.635,0.333 1.948,0.531 0.313,0.198 10 false *2 1.969,1.594 2.281,1.792 0.313,0.198 10 false *3

If the rear seat headrest assembly does not operate correctly during the retraction operation, adjust in the tightening direction.

HINT:

Tightening the rear seat lock control cable excessively will prevent the rear seat headrest assembly from locking. Therefore, after adjustment, check that the rear seat headrest assembly locks smoothly.


Text in Illustration
*1 Cable End Side
*2 Tightening Direction
*3 Loosening Direction