Home › Vehicle Interior › SEAT › FRONT POWER SEAT CONTROL SYSTEM (w/ Memory) › 2015.06–2017.08
RM27T0E _58 Vehicle Interior _053737 SEAT _0261110 FRONT POWER SEAT CONTROL SYSTEM(w/ Memory) J

SEAT  FRONT POWER SEAT CONTROL SYSTEM(w/ Memory)  Power Seat Position is not Memorized  


DESCRIPTION

When the seat memory SET switch and a memory switch (M1 or M2) are pressed simultaneously, the main body ECU commands the position control ECU through CAN communication to record the value of each position sensor.

WIRING DIAGRAM

B205120E02
0.591,4.288 2.339,4.440 1.748,0.151 10 : CAN Communication Line 3.378,2.776 3.705,2.927 0.327,0.151 10 G63 0.82,2.935 2.124,3.086 1.304,0.151 10 Seat Memory Switch 0.82,2.776 1.698,2.927 0.878,0.151 10 K9*1, J10*2 0.656,2.089 0.881,2.240 0.225,0.151 10 1 0.873,2.292 1.099,2.443 0.225,0.151 10 E 3.076,0.9 3.254,1.052 0.178,0.151 10 25 3.076,1.501 3.254,1.652 0.178,0.151 10 27 3.076,2.089 3.262,2.240 0.186,0.151 10 26 2.155,0.9 2.381,1.052 0.225,0.151 10 3 1.831,1.099 2.051,1.250 0.220,0.151 10 M1 1.837,1.699 2.051,1.850 0.214,0.151 10 M2 1.714,2.292 2.050,2.443 0.336,0.151 10 MRY 3.358,0.991 3.592,1.142 0.235,0.151 10 M1 2.155,1.501 2.381,1.652 0.225,0.151 10 4 3.358,1.591 3.592,1.743 0.235,0.151 10 M2 2.155,2.089 2.381,2.240 0.225,0.151 10 2 3.363,2.179 3.695,2.330 0.332,0.151 10 MM 3.378,2.935 4.395,3.086 1.017,0.151 10 Main Body ECU 5.426,2.776 6.993,2.950 1.567,0.174 10 Front Power Seat Switch 0.138,3.576 0.896,3.741 0.758,0.165 10 *1: for LHD 0.138,3.91 0.896,4.075 0.758,0.165 10 *2: for RHD

CAUTION / NOTICE / HINT

NOTICE:

First perform the communication function inspections in How to Proceed with Troubleshooting to confirm that there are no CAN communication malfunctions before troubleshooting this symptom.


PROCEDURE

1.CHECK FRONT POWER SEAT CONTROL FUNCTION
a.

Check that each function of the power seat operates normally by using the front power seat switches.

OK:

Each function of power seat operates normally by using seat switches.




OK

2.READ VALUE USING INTELLIGENT TESTER (SEAT POSITION MEMORY)

NG

2.READ VALUE USING INTELLIGENT TESTER (SEAT POSITION MEMORY)
a.

Use the seat memory switch to record the seat position (See page Vehicle Interior>SEAT>FRONT POWER SEAT CONTROL SYSTEM (w/ Memory)>OPERATION CHECK).

NOTICE:
·

The seat position will not be recorded if the SET switch and both memory switches are pressed simultaneously.

·

If a memorizing operation has failed, release all switches. The seat memory function does not operate unless the switches are released.




b.

Using the intelligent tester, read the Data List (See page Vehicle Interior>SEAT>FRONT POWER SEAT CONTROL SYSTEM (w/ Memory)>DATA LIST / ACTIVE TEST).

Driver Seat
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
Seat Memory No1 Seat position memorized with M1 switch / Mem or Not Mem Mem: Memorized
Not Mem: Not memorized
-
Seat Memory No2 Seat position memorized with M2 switch / Mem or Not Mem Mem: Memorized
Not Mem: Not memorized
-

OK:

"Mem" is displayed on the tester.




OK

END

NG

3.READ VALUE USING INTELLIGENT TESTER (SEAT MEMORY SWITCH)
3.READ VALUE USING INTELLIGENT TESTER (SEAT MEMORY SWITCH)
a.

Using the intelligent tester, read the Data List (See page Vehicle Interior>SEAT>FRONT POWER SEAT CONTROL SYSTEM (w/ Memory)>DATA LIST / ACTIVE TEST).

Main Body
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
M1 Switch Seat memory switch M1 signal / ON or OFF ON: Seat memory switch M1 on
OFF: Seat memory switch M1 off
-
M2 Switch Seat memory switch M2 signal / ON or OFF ON: Seat memory switch M2 on
OFF: Seat memory switch M2 off
-
SET Switch Seat memory switch SET signal / ON or OFF ON: Seat memory switch SET on
OFF: Seat memory switch SET off
-

OK:

On intelligent tester screen, each item changes between ON and OFF according to above chart.




OK

4.CHECK FRONT POWER SEAT SWITCH (OPERATION)

NG

5.INSPECT SEAT MEMORY SWITCH
4.CHECK FRONT POWER SEAT SWITCH (OPERATION)
a.

Replace the front power seat switch with a new one or normally operating one.


b.

Use the seat memory switch to record the seat position (See page Vehicle Interior>SEAT>FRONT POWER SEAT CONTROL SYSTEM (w/ Memory)>OPERATION CHECK).


c.

Refer to the Data List for the driver seat and check that the memory operation is completed normally.

OK:

Seat position is recorded normally.




OK

END (FRONT POWER SEAT SWITCH WAS DEFECTIVE)

NG

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

5.INSPECT SEAT MEMORY SWITCH
a.
B199457E01
0.696,1.258 0.926,1.414 0.229,0.156 10 M2 1.321,1.838 1.533,1.994 0.212,0.156 10 M1 2.497,1.263 2.621,1.418 0.123,0.156 10 E 1.806,1.838 2.134,1.994 0.328,0.156 10 MRY 1.388,1.35 0.981,1.35 false 2.457,1.35 2.05,1.35 false 1.625,1.413 1.444,1.7 1.444,1.7 1.444,1.81 false 1.822,1.413 2.002,1.7 2.002,1.7 2.002,1.81 false

Remove the seat memory switch (See page Vehicle Interior>SEAT>SEAT MEMORY SWITCH>REMOVAL).


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
3 (M1) - 1 (E) Seat memory switch M1 pressed Below 1 Ω
4 (M2) - 1 (E) Seat memory switch M2 pressed Below 1 Ω
2 (MRY) - 1 (E) Seat memory switch SET pressed Below 1 Ω




OK

6.CHECK HARNESS AND CONNECTOR (SEAT MEMORY SWITCH - MAIN BODY ECU AND BODY GROUND)

NG

REPLACE SEAT MEMORY SWITCH

6.CHECK HARNESS AND CONNECTOR (SEAT MEMORY SWITCH - MAIN BODY ECU AND BODY GROUND)
a.

Disconnect the K9*1 or J10*2 switch connector.

*1: for LHD

*2: for RHD



b.

Disconnect the G63 ECU connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for LHD
Tester Connection Condition Specified Condition
G63-25 (M1) - K9-3 (M1) Always Below 1 Ω
G63-27 (M2) - K9-4 (M2) Always Below 1 Ω
G63-26 (MM) - K9-2 (MRY) Always Below 1 Ω
K9-1 (E) - Body ground Always Below 1 Ω
G63-25 (M1) - Body ground Always 10 kΩ or higher
G63-27 (M2) - Body ground Always 10 kΩ or higher
G63-26 (MM) - Body ground Always 10 kΩ or higher

for RHD
Tester Connection Condition Specified Condition
G63-25 (M1) - J10-3 (M1) Always Below 1 Ω
G63-27 (M2) - J10-4 (M2) Always Below 1 Ω
G63-26 (MM) - J10-2 (MRY) Always Below 1 Ω
J10-1 (E) - Body ground Always Below 1 Ω
G63-25 (M1) - Body ground Always 10 kΩ or higher
G63-27 (M2) - Body ground Always 10 kΩ or higher
G63-26 (MM) - Body ground Always 10 kΩ or higher




OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR