Home › Vehicle Interior › SEAT › FRONT POWER SEAT CONTROL SYSTEM (w/ Memory)
RM27T0E _58 Vehicle Interior _053737 SEAT _0261110 FRONT POWER SEAT CONTROL SYSTEM(w/ Memory) C

SEAT  FRONT POWER SEAT CONTROL SYSTEM(w/ Memory)  B2650  Slide Sensor Malfunction  


DESCRIPTION

When the front power seat switch does not receive a sensor signal despite forward or backward movement of the seat by power seat motor operation, this DTC is stored.

DTC Code DTC Detection Condition Trouble Area
B2650 The forward and backward lock detection position of the sensor is the same.
·

Front power seat switch

·

Separate type front seat cushion spring assembly (Slide motor)

·

Harness or connector



WIRING DIAGRAM

B238655E01
1.794,0.761 2.135,0.917 0.340,0.156 10 FWD 1.726,1.265 2.134,1.427 0.409,0.162 10 BACK 1.873,1.772 2.136,1.931 0.263,0.159 10 O/P 1.803,2.279 2.135,2.435 0.332,0.156 10 GND 2.237,0.648 2.485,0.805 0.248,0.157 10 4*1 2.237,1.155 2.473,1.312 0.236,0.157 10 1*1 2.237,1.659 2.344,1.816 0.106,0.157 10 2 2.237,2.171 2.344,2.329 0.106,0.157 10 3 5.164,0.761 5.558,0.917 0.394,0.156 10 SLD+ 5.164,1.265 5.524,1.427 0.359,0.162 10 SLD- 5.164,1.772 5.605,1.931 0.441,0.159 10 SSRS 5.164,2.279 5.599,2.435 0.435,0.156 10 SGND 4.891,0.586 4.997,0.744 0.106,0.157 10 3 4.891,1.093 4.997,1.250 0.106,0.157 10 4 4.891,1.597 4.997,1.754 0.106,0.157 10 5 4.891,2.109 4.997,2.267 0.106,0.157 10 1 4.558,0.586 4.664,0.744 0.106,0.157 10 3 4.558,1.093 4.664,1.250 0.106,0.157 10 4 4.558,1.597 4.664,1.754 0.106,0.157 10 5 4.558,2.109 4.664,2.267 0.106,0.157 10 1 1.343,2.63 2.166,2.799 0.824,0.169 10 b1*1, a1*2 1.343,2.804 2.079,2.962 0.736,0.158 10 Slide Motor 1.045,3.402 2.691,3.749 1.646,0.348 10 Separate Type Front Seat Cushion Spring Assembly 4.894,3.402 6.466,3.559 1.571,0.158 10 Front Power Seat Switch 0.123,4.091 0.859,4.251 0.736,0.159 10 *1: for LHD 0.123,4.424 0.903,4.583 0.780,0.159 10 *2: for RHD 4.869,0.926 5.025,1.079 0.156,0.153 10 *1 4.869,1.936 5.025,2.088 0.156,0.153 10 *1 4.869,1.431 5.025,1.584 0.156,0.153 10 *1 4.869,2.448 5.025,2.600 0.156,0.153 10 *1 4.536,0.925 4.692,1.078 0.156,0.153 10 *2 4.536,1.935 4.692,2.088 0.156,0.153 10 *2 4.536,1.431 4.692,1.583 0.156,0.153 10 *2 4.536,2.447 4.692,2.600 0.156,0.153 10 *2 2.237,0.492 2.485,0.650 0.248,0.157 10 1*2 2.237,0.999 2.473,1.156 0.236,0.157 10 4*2 4.866,0.759 5.042,0.912 0.176,0.152 10 b4 4.522,0.76 4.700,0.912 0.179,0.152 10 a4 4.866,1.265 5.042,1.418 0.176,0.152 10 b4 4.522,1.266 4.701,1.418 0.179,0.152 10 a4 4.865,1.769 5.042,1.922 0.176,0.152 10 b5 4.522,1.77 4.700,1.922 0.179,0.152 10 a5 4.866,2.282 5.042,2.435 0.176,0.152 10 b5 4.522,2.283 4.701,2.435 0.179,0.152 10 a5

PROCEDURE

1.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (POWER SEAT MOTOR FUNCTION)
a.

Select the Active Test, use the intelligent tester to generate a control command, and then check the power seat motor function (See page Vehicle Interior>SEAT>FRONT POWER SEAT CONTROL SYSTEM (w/ Memory)>DATA LIST / ACTIVE TEST).

Driver Seat
Tester Display Test Part Control Range Diagnostic Note
Seat Slide Operation Seat sliding operation Front / OFF / Rear -

OK:

Motor operates normally.




OK

2.CHECK FRONT POWER SEAT SWITCH (SLIDE MOTOR CIRCUIT)

NG

5.INSPECT SEPARATE TYPE FRONT SEAT CUSHION SPRING ASSEMBLY (SLIDE MOTOR)
2.CHECK FRONT POWER SEAT SWITCH (SLIDE MOTOR CIRCUIT)
a.
U169720E01
0.139,0.104 0.312,0.274 0.173,0.169 10 *a 1.215,1.815 1.543,1.967 0.328,0.152 10 O/P 1.87,1.815 2.197,1.967 0.328,0.152 10 GND 1.581,1.355 1.37,1.681 1.37,1.681 1.37,1.798 false 1.853,1.355 2.064,1.681 2.064,1.681 2.064,1.798 false 0.633,0.818 0.812,0.975 0.179,0.158 10 *A 0.633,1.264 0.812,1.422 0.179,0.158 10 *B 0.341,0.966 0.524,1.123 0.183,0.157 10 b1 0.336,1.41 0.509,1.567 0.172,0.157 10 a1

Disconnect the b1*1 or a1*2 motor connector.

*1: for LHD

*2: for RHD



b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
for LHD
Tester Connection Switch Condition Specified Condition
b1-2 (O/P) - b1-3 (GND) Sliding switch on 4.8 to 5.1 V

for RHD
Tester Connection Switch Condition Specified Condition
a1-2 (O/P) - a1-3 (GND) Sliding switch on 4.8 to 5.1 V


Text in Illustration
*A for LHD
*B for RHD
*a Front view of wire harness connector
(to Separate Type Front Seat Cushion Spring Assembly [Slide Motor])



OK

3.CHECK SEPARATE TYPE FRONT SEAT CUSHION SPRING ASSEMBLY (SLIDE MOTOR)

NG

4.CHECK HARNESS AND CONNECTOR (FRONT POWER SEAT SWITCH - SLIDE MOTOR)
3.CHECK SEPARATE TYPE FRONT SEAT CUSHION SPRING ASSEMBLY (SLIDE MOTOR)
a.
U169728E01
0.126,0.116 0.300,0.285 0.173,0.169 10 *a 1.692,1.826 1.960,1.979 0.268,0.152 10 O/P 0.62,0.829 0.799,0.987 0.179,0.158 10 *A 0.62,1.276 0.799,1.433 0.179,0.158 10 *B 1.84,1.478 1.84,1.795 false 0.336,0.974 0.510,1.131 0.174,0.157 10 b1 0.323,1.419 0.495,1.575 0.173,0.157 10 a1

Connect the b1*1 or a1*2 motor connector.

*1: for LHD

*2: for RHD



b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
for LHD
Tester Connection Switch Condition Specified Condition
b1-2 (O/P) - Body ground Sliding switch on 4.5 to 4.8 V

for RHD
Tester Connection Switch Condition Specified Condition
a1-2 (O/P) - Body ground Sliding switch on 4.5 to 4.8 V


Text in Illustration
*A for LHD
*B for RHD
*a Component with harness connected
(Separate Type Front Seat Cushion Spring Assembly [Slide Motor])



OK

NG

REPLACE SEPARATE TYPE FRONT SEAT CUSHION SPRING ASSEMBLY (SLIDE MOTOR)

4.CHECK HARNESS AND CONNECTOR (FRONT POWER SEAT SWITCH - SLIDE MOTOR)

*1: for LHD

*2: for RHD


a.

Disconnect the b5*1 or a5*2 switch connector.


b.

Disconnect the b1*1 or a1*2 motor connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for LHD
Tester Connection Condition Specified Condition
b5-5 (SSRS) - b1-2 (O/P) Always Below 1 Ω
b5-1 (SGND) - b1-3 (GND) Always Below 1 Ω
b5-5 (SSRS) - Body ground Always 10 kΩ or higher
b5-1 (SGND) - Body ground Always 10 kΩ or higher

for RHD
Tester Connection Condition Specified Condition
a5-5 (SSRS) - a1-2 (O/P) Always Below 1 Ω
a5-1 (SGND) - a1-3 (GND) Always Below 1 Ω
a5-5 (SSRS) - Body ground Always 10 kΩ or higher
a5-1 (SGND) - Body ground Always 10 kΩ or higher




OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.INSPECT SEPARATE TYPE FRONT SEAT CUSHION SPRING ASSEMBLY (SLIDE MOTOR)
a.
B238714E01
1.065,1.449 1.562,1.606 0.498,0.156 10 FWD*A 1.98,1.449 2.549,1.611 0.569,0.162 10 BACK*A 1.98,1.798 2.462,1.954 0.482,0.156 10 FWD*B 1.065,1.798 1.622,1.960 0.557,0.162 10 BACK*B 1.455,1.07 1.258,1.344 1.258,1.344 1.258,1.434 false 2.005,1.07 2.202,1.344 2.202,1.344 2.202,1.434 false

Remove the separate type front seat cushion spring assembly (slide motor) (See page Vehicle Interior>SEAT>FRONT POWER SEAT CONTROL SYSTEM(w/o Memory)>PRECAUTION).


b.

Check if the seat cushion spring moves smoothly when the battery is connected to the slide motor connector terminals.

OK:
for LHD
Measurement Condition Specified Condition
Battery positive (+) → 4 (FWD)
Battery negative (-) → 1 (BACK)
Seat cushion spring moves forward
Battery positive (+) → 1 (BACK)
Battery negative (-) → 4 (FWD)
Seat cushion spring moves backward

for RHD
Measurement Condition Specified Condition
Battery positive (+) → 1 (FWD)
Battery negative (-) → 4 (BACK)
Seat cushion spring moves forward
Battery positive (+) → 4 (BACK)
Battery negative (-) → 1 (FWD)
Seat cushion spring moves backward


Text in Illustration
*A for LHD
*B for RHD



OK

6.CHECK HARNESS AND CONNECTOR (FRONT POWER SEAT SWITCH - SLIDE MOTOR)

NG

REPLACE SEPARATE TYPE FRONT SEAT CUSHION SPRING ASSEMBLY (SLIDE MOTOR)

6.CHECK HARNESS AND CONNECTOR (FRONT POWER SEAT SWITCH - SLIDE MOTOR)

*1: for LHD

*2: for RHD


a.

Disconnect the b4*1 or a4*2 switch connector.


b.

Disconnect the b1*1 or a1*2 motor connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for LHD
Tester Connection Condition Specified Condition
b4-3 (SLD+) - b1-4 (FWD) Always Below 1 Ω
b4-4 (SLD-) - b1-1 (BACK) Always Below 1 Ω
b4-3 (SLD+) - Body ground Always 10 kΩ or higher
b4-4 (SLD-) - Body ground Always 10 kΩ or higher

for RHD
Tester Connection Condition Specified Condition
a4-3 (SLD+) - a1-1 (FWD) Always Below 1 Ω
a4-4 (SLD-) - a1-4 (BACK) Always Below 1 Ω
a4-3 (SLD+) - Body ground Always 10 kΩ or higher
a4-4 (SLD-) - Body ground Always 10 kΩ or higher




OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR