Home › Vehicle Interior › SEAT › FRONT POWER SEAT CONTROL SYSTEM (w/ Memory)
RM27T0E _58 Vehicle Interior _053737 SEAT _0261110 FRONT POWER SEAT CONTROL SYSTEM(w/ Memory) C

SEAT  FRONT POWER SEAT CONTROL SYSTEM(w/ Memory)  B2651  Reclining Sensor Malfunction  


DESCRIPTION

When the front power seat switch does not receive a sensor signal despite forward or backward movement of the seatback by power seat motor operation, this DTC is stored.

DTC Code DTC Detection Condition Trouble Area
B2651 The forward and backward lock detection position of the sensor is the same.
·

Front power seat switch

·

Separate type front seatback assembly (Reclining motor)

·

Harness or connector



WIRING DIAGRAM

B238655E02
1.794,0.761 2.135,0.917 0.340,0.156 10 FWD 1.726,1.265 2.134,1.427 0.409,0.162 10 BACK 1.874,1.772 2.136,1.931 0.262,0.159 10 O/P 1.803,2.279 2.135,2.435 0.332,0.156 10 GND 2.237,0.648 2.485,0.805 0.248,0.157 10 1 2.237,1.155 2.473,1.312 0.236,0.157 10 4 2.237,1.659 2.344,1.816 0.106,0.157 10 2 2.237,2.171 2.344,2.329 0.106,0.157 10 3 5.164,0.761 5.558,0.917 0.394,0.156 10 RCL+ 5.164,1.265 5.524,1.427 0.359,0.162 10 RCL- 5.164,1.772 5.605,1.931 0.441,0.159 10 SSRR 5.164,2.279 5.599,2.435 0.435,0.156 10 SGND 4.891,0.586 4.997,0.744 0.106,0.157 10 9 4.851,1.093 5.028,1.250 0.177,0.157 10 11 4.851,1.597 5.031,1.754 0.180,0.157 10 11 4.891,2.109 4.997,2.267 0.106,0.157 10 1 4.558,0.586 4.664,0.744 0.106,0.157 10 9 4.518,1.093 4.695,1.250 0.177,0.157 10 11 4.518,1.597 4.695,1.754 0.177,0.157 10 11 4.558,2.109 4.664,2.267 0.106,0.157 10 1 1.273,2.63 2.166,2.812 0.894,0.183 10 f1*1, e1*2 1.273,2.804 2.284,2.962 1.011,0.158 10 Reclining Motor 0.871,3.402 2.799,3.749 1.928,0.348 10 Separate Type Front Seatback Assembly 4.894,3.402 6.466,3.559 1.571,0.158 10 Front Power Seat Switch 0.123,4.091 0.859,4.251 0.736,0.159 10 *1: for LHD 0.123,4.424 0.903,4.583 0.780,0.159 10 *2: for RHD 4.869,0.926 5.025,1.079 0.156,0.153 10 *1 4.869,1.936 5.025,2.088 0.156,0.153 10 *1 4.869,1.431 5.025,1.584 0.156,0.153 10 *1 4.869,2.448 5.025,2.600 0.156,0.153 10 *1 4.536,0.925 4.692,1.078 0.156,0.153 10 *2 4.536,1.935 4.692,2.088 0.156,0.153 10 *2 4.536,1.431 4.692,1.583 0.156,0.153 10 *2 4.536,2.447 4.692,2.600 0.156,0.153 10 *2 4.858,0.759 5.039,0.915 0.181,0.156 10 b4 4.528,0.757 4.712,0.913 0.184,0.156 10 a4 4.858,1.263 5.039,1.419 0.181,0.156 10 b4 4.528,1.261 4.711,1.417 0.184,0.156 10 a4 4.858,1.768 5.039,1.924 0.181,0.156 10 b5 4.526,1.766 4.710,1.922 0.184,0.156 10 a5 4.858,2.282 5.039,2.438 0.181,0.156 10 b5 4.529,2.28 4.712,2.436 0.184,0.156 10 a5

PROCEDURE

1.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (POWER SEAT MOTOR FUNCTION)
a.

Select the Active Test, use the intelligent tester to generate a control command, and then check the power seat motor function (See page Vehicle Interior>SEAT>FRONT POWER SEAT CONTROL SYSTEM (w/ Memory)>DATA LIST / ACTIVE TEST).

Driver Seat
Tester Display Test Part Control Ranger Diagnostic Note
Seat Reclining Seat reclining operation Front / OFF / Rear -

OK:

Motor operates normally.




OK

2.CHECK FRONT POWER SEAT SWITCH (RECLINING MOTOR CIRCUIT)

NG

5.INSPECT SEPARATE TYPE FRONT SEATBACK ASSEMBLY (RECLINING MOTOR)
2.CHECK FRONT POWER SEAT SWITCH (RECLINING MOTOR CIRCUIT)
a.
U169721E01
0.139,0.104 0.312,0.274 0.173,0.169 10 *a 1.22,1.815 1.487,1.967 0.267,0.152 10 O/P 1.87,1.815 2.197,1.967 0.328,0.152 10 GND 1.581,1.355 1.37,1.681 1.37,1.681 1.37,1.798 false 1.853,1.355 2.064,1.681 2.064,1.681 2.064,1.798 false 0.633,0.818 0.812,0.975 0.179,0.158 10 *A 0.633,1.264 0.812,1.422 0.179,0.158 10 *B 0.365,0.962 0.501,1.118 0.136,0.156 10 f1 0.333,1.411 0.505,1.567 0.172,0.156 10 e1

Disconnect the f1*1 or e1*2 motor connector.

*1: for LHD

*2: for RHD



b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
for LHD
Tester Connection Switch Condition Specified Condition
f1-2 (O/P) - f1-3 (GND) Reclining switch on 4.8 to 5.1 V

for RHD
Tester Connection Switch Condition Specified Condition
e1-2 (O/P) - e1-3 (GND) Reclining switch on 4.8 to 5.1 V


Text in Illustration
*A for LHD
*B for RHD
*a Front view of wire harness connector
(to Separate Type Front Seatback Assembly [Reclining Motor])



OK

3.CHECK SEPARATE TYPE FRONT SEATBACK ASSEMBLY (RECLINING MOTOR)

NG

4.CHECK HARNESS AND CONNECTOR (FRONT POWER SEAT SWITCH - RECLINING MOTOR)
3.CHECK SEPARATE TYPE FRONT SEATBACK ASSEMBLY (RECLINING MOTOR)
a.
U169729E01
0.126,0.116 0.300,0.285 0.173,0.169 10 *a 1.698,1.826 1.959,1.979 0.261,0.152 10 O/P 0.62,0.829 0.799,0.987 0.179,0.158 10 *A 0.62,1.276 0.799,1.433 0.179,0.158 10 *B 1.84,1.478 1.84,1.795 false 0.351,0.976 0.486,1.132 0.134,0.156 10 f1 0.323,1.42 0.499,1.576 0.175,0.156 10 e1

Connect the f1*1 or e1*2 motor connector.

*1: for LHD

*2: for RHD



b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
for LHD
Tester Connection Switch Condition Specified Condition
f1-2 (O/P) - Body ground Reclining switch on 4.5 to 4.8 V

for RHD
Tester Connection Switch Condition Specified Condition
e1-2 (O/P) - Body ground Reclining switch on 4.5 to 4.8 V


Text in Illustration
*A for LHD
*B for RHD
*a Component with harness connected
(Separate Type Front Seatback Assembly [Reclining Motor])



OK

NG

REPLACE SEPARATE TYPE FRONT SEATBACK ASSEMBLY (RECLINING MOTOR)

4.CHECK HARNESS AND CONNECTOR (FRONT POWER SEAT SWITCH - RECLINING MOTOR)

*1: for LHD

*2: for RHD


a.

Disconnect the b5*1 or a5*2 switch connector.


b.

Disconnect the f1*1 or e1*2 motor connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for LHD
Tester Connection Condition Specified Condition
b5-11 (SSRR) - f1-2 (O/P) Always Below 1 Ω
b5-1 (SGND) - f1-3 (GND) Always Below 1 Ω
b5-11 (SSRR) - Body ground Always 10 kΩ or higher
b5-1 (SGND) - Body ground Always 10 kΩ or higher

for RHD
Tester Connection Condition Specified Condition
a5-11 (SSRR) - e1-2 (O/P) Always Below 1 Ω
a5-1 (SGND) - e1-3 (GND) Always Below 1 Ω
a5-11 (SSRR) - Body ground Always 10 kΩ or higher
a5-1 (SGND) - Body ground Always 10 kΩ or higher




OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.INSPECT SEPARATE TYPE FRONT SEATBACK ASSEMBLY (RECLINING MOTOR)
a.
B238256E01
1.843,1.654 2.194,1.811 0.352,0.156 10 FWD 1.197,1.654 1.613,1.816 0.416,0.162 10 BACK 1.995,1.279 1.995,1.617 false 1.465,1.279 1.465,1.617 false

Remove the separate type front seatback assembly (reclining motor) (See page Vehicle Interior>SEAT>FRONT SEAT ASSEMBLY (for Power Seat)>DISASSEMBLY).


b.

Check if the seatback moves smoothly when the battery is connected to the reclining motor connector terminals.

OK:
Measurement Condition Operational Direction
Battery positive (+) → 1 (FWD)
Battery negative (-) → 4 (BACK)
Seatback moves forward
Battery positive (+) → 4 (BACK)
Battery negative (-) → 1 (FWD)
Seatback moves backward




OK

6.CHECK HARNESS AND CONNECTOR (FRONT POWER SEAT SWITCH - RECLINING MOTOR)

NG

REPLACE SEPARATE TYPE FRONT SEATBACK ASSEMBLY (RECLINING MOTOR)

6.CHECK HARNESS AND CONNECTOR (FRONT POWER SEAT SWITCH - RECLINING MOTOR)

*1: for LHD

*2: for RHD


a.

Disconnect the b4*1 or a4*2 switch connector.


b.

Disconnect the f1*1 or e1*2 motor connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for LHD
Tester Connection Condition Specified Condition
b4-9 (RCL+) - f1-1 (FWD) Always Below 1 Ω
b4-11 (RCL-) - f1-4 (BACK) Always Below 1 Ω
b4-9 (RCL+) - Body ground Always 10 kΩ or higher
b4-11 (RCL-) - Body ground Always 10 kΩ or higher

for RHD
Tester Connection Condition Specified Condition
a4-9 (RCL+) - e1-4 (FWD) Always Below 1 Ω
a4-11 (RCL-) - e1-5 (BACK) Always Below 1 Ω
a4-9 (RCL+) - Body ground Always 10 kΩ or higher
a4-11 (RCL-) - Body ground Always 10 kΩ or higher




OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR