Home › Vehicle Interior › SEAT › FRONT POWER SEAT CONTROL SYSTEM (w/ Memory)
RM27T0E _58 Vehicle Interior _053737 SEAT _0261110 FRONT POWER SEAT CONTROL SYSTEM(w/ Memory) C

SEAT  FRONT POWER SEAT CONTROL SYSTEM(w/ Memory)  B2652  Front Vertical Sensor Malfunction  


DESCRIPTION

When the front power seat switch does not receive a sensor signal despite upward or downward movement of the front of the seat cushion by power seat motor operation, this DTC is stored.

DTC Code DTC Detection Condition Trouble Area
B2652 The upward and downward lock detection position is of the sensor the same.
·

Front power seat switch

·

Separate type front seat cushion assembly (Front vertical motor)

·

Harness or connector



WIRING DIAGRAM

B238655E03
1.917,0.761 2.136,0.917 0.219,0.156 10 UP 1.671,1.265 2.134,1.427 0.462,0.162 10 DOWN 1.868,1.772 2.136,1.931 0.267,0.159 10 O/P 1.803,2.279 2.135,2.435 0.332,0.156 10 GND 2.237,0.648 2.485,0.805 0.248,0.157 10 4 2.237,1.155 2.473,1.312 0.236,0.157 10 1 2.237,1.659 2.344,1.816 0.106,0.157 10 2 2.237,2.171 2.344,2.329 0.106,0.157 10 3 5.164,0.761 5.558,0.917 0.394,0.156 10 FRV+ 5.164,1.265 5.524,1.427 0.359,0.162 10 FRV- 5.164,1.772 5.605,1.931 0.441,0.159 10 SSFV 5.164,2.279 5.599,2.435 0.435,0.156 10 SGND 4.891,0.586 4.997,0.744 0.106,0.157 10 8 4.891,1.093 4.997,1.250 0.106,0.157 10 5 4.891,1.597 4.997,1.754 0.106,0.157 10 3 4.891,2.109 4.997,2.267 0.106,0.157 10 1 4.558,0.586 4.664,0.744 0.106,0.157 10 8 4.558,1.093 4.664,1.250 0.106,0.157 10 5 4.558,1.597 4.664,1.754 0.106,0.157 10 3 4.558,2.109 4.664,2.267 0.106,0.157 10 1 1.174,2.634 1.865,2.795 0.691,0.161 10 b2*1, a2*2 1.174,2.809 2.442,2.966 1.268,0.158 10 Front Vertical Motor 1.045,3.402 2.691,3.749 1.646,0.348 10 Separate Type Front Seat Cushion Spring Assembly 4.894,3.402 6.466,3.559 1.571,0.158 10 Front Power Seat Switch 0.123,4.091 0.859,4.251 0.736,0.159 10 *1: for LHD 0.123,4.424 0.903,4.583 0.780,0.159 10 *2: for RHD 4.869,0.926 5.025,1.079 0.156,0.153 10 *1 4.869,1.936 5.025,2.088 0.156,0.153 10 *1 4.869,1.431 5.025,1.584 0.156,0.153 10 *1 4.869,2.448 5.025,2.600 0.156,0.153 10 *1 4.536,0.925 4.692,1.078 0.156,0.153 10 *2 4.536,1.935 4.692,2.088 0.156,0.153 10 *2 4.536,1.431 4.692,1.583 0.156,0.153 10 *2 4.536,2.447 4.692,2.600 0.156,0.153 10 *2 4.856,0.757 5.033,0.913 0.176,0.155 10 b4 4.524,0.757 4.699,0.913 0.175,0.155 10 a4 4.857,1.262 5.034,1.417 0.176,0.155 10 b4 4.525,1.262 4.700,1.417 0.175,0.155 10 a4 4.857,1.768 5.034,1.924 0.176,0.155 10 b5 4.525,1.768 4.700,1.924 0.175,0.155 10 a5 4.857,2.282 5.033,2.438 0.176,0.155 10 b5 4.524,2.282 4.699,2.438 0.175,0.155 10 a5

PROCEDURE

1.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (POWER SEAT MOTOR FUNCTION)
a.

Select the Active Test, use the intelligent test to generate a control command, and then check the power seat motor function (See page Vehicle Interior>SEAT>FRONT POWER SEAT CONTROL SYSTEM (w/ Memory)>DATA LIST / ACTIVE TEST).

Driver Seat
Tester Display Test Part Control Range Diagnostic Note
Front Vertical Operation Seat front vertical operation Up / OFF / Down -

OK:

Motor operates normally.




OK

2.CHECK FRONT POWER SEAT SWITCH (FRONT VERTICAL MOTOR CIRCUIT)

NG

5.INSPECT SEPARATE TYPE FRONT SEAT CUSHION SPRING ASSEMBLY (FRONT VERTICAL MOTOR)
2.CHECK FRONT POWER SEAT SWITCH (FRONT VERTICAL MOTOR CIRCUIT)
a.
U169722E01
0.139,0.104 0.312,0.274 0.173,0.169 10 *a 1.221,1.815 1.491,1.967 0.270,0.152 10 O/P 1.87,1.815 2.197,1.967 0.328,0.152 10 GND 1.581,1.355 1.37,1.681 1.37,1.681 1.37,1.798 false 1.853,1.355 2.064,1.681 2.064,1.681 2.064,1.798 false 0.633,0.818 0.812,0.975 0.179,0.158 10 *A 0.633,1.264 0.812,1.422 0.179,0.158 10 *B 0.336,0.965 0.511,1.119 0.174,0.154 10 b2 0.336,1.41 0.508,1.564 0.172,0.154 10 a2

Disconnect the b2*1 or a2*2 motor connector.

*1: for LHD

*2: for RHD



b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
for LHD
Tester Connection Switch Condition Specified Condition
b2-2 (O/P) - b2-3 (GND) Front vertical switch on 4.8 to 5.1 V

for RHD
Tester Connection Switch Condition Specified Condition
a2-2 (O/P) - a2-3 (GND) Front vertical switch on 4.8 to 5.1 V


Text in Illustration
*A for LHD
*B for RHD
*a Front view of wire harness connector
(to Separate Type Front Seat Cushion Spring Assembly [Front Vertical Motor])



OK

3.CHECK SEPARATE TYPE FRONT SEAT CUSHION SPRING ASSEMBLY (FRONT VERTICAL MOTOR)

NG

4.CHECK HARNESS AND CONNECTOR (FRONT POWER SEAT SWITCH - FRONT VERTICAL MOTOR)
3.CHECK SEPARATE TYPE FRONT SEAT CUSHION SPRING ASSEMBLY (FRONT VERTICAL MOTOR)
a.
U169730E01
0.126,0.116 0.300,0.285 0.173,0.169 10 *a 1.702,1.826 1.973,1.979 0.271,0.152 10 O/P 0.62,0.829 0.799,0.987 0.179,0.158 10 *A 0.62,1.276 0.799,1.433 0.179,0.158 10 *B 1.84,1.478 1.84,1.795 false 0.321,0.976 0.493,1.130 0.172,0.154 10 b2 0.321,1.422 0.496,1.576 0.175,0.154 10 a2

Connect the b2*1 or a2*2 motor connector.

*1: for LHD

*2: for RHD



b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
for LHD
Tester Connection Switch Condition Specified Condition
b2-2 (O/P) - Body ground Front vertical switch on 4.5 to 4.8 V

for RHD
Tester Connection Switch Condition Specified Condition
a2-2 (O/P) - Body ground Front vertical switch on 4.5 to 4.8 V


Text in Illustration
*A for LHD
*B for RHD
*a Component with harness connected
(Separate Type Front Seat Cushion Spring Assembly [Front Vertical Motor])



OK

NG

REPLACE SEPARATE TYPE FRONT SEAT CUSHION SPRING ASSEMBLY (FRONT VERTICAL MOTOR)

4.CHECK HARNESS AND CONNECTOR (FRONT POWER SEAT SWITCH - FRONT VERTICAL MOTOR)

*1: for LHD

*2: for RHD


a.

Disconnect the b5*1 or a5*2 switch connector.


b.

Disconnect the b2*1 or a2*2 motor connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for LHD
Tester Connection Condition Specified Condition
b5-3 (SSFV) - b2-2 (O/P) Always Below 1 Ω
b5-1 (SGND) - b2-3 (GND) Always Below 1 Ω
b5-3 (SSFV) - Body ground Always 10 kΩ or higher
b5-1 (SGND) - Body ground Always 10 kΩ or higher

for RHD
Tester Connection Condition Specified Condition
a5-3 (SSFV) - a2-2 (O/P) Always Below 1 Ω
a5-1 (SGND) - a2-3 (GND) Always Below 1 Ω
a5-3 (SSFV) - Body ground Always 10 kΩ or higher
a5-1 (SGND) - Body ground Always 10 kΩ or higher




OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.INSPECT SEPARATE TYPE FRONT SEAT CUSHION SPRING ASSEMBLY (FRONT VERTICAL MOTOR)
a.
B238256E02
1.761,1.654 2.226,1.811 0.465,0.156 10 DOWN 1.34,1.654 1.556,1.816 0.215,0.162 10 UP 1.995,1.279 1.995,1.617 false 1.465,1.279 1.465,1.617 false

Remove the separate type front seat cushion spring assembly (front vertical motor) (See page Vehicle Interior>SEAT>FRONT SEAT ASSEMBLY (for Power Seat)>DISASSEMBLY).


b.

Check if the seat cushion spring moves smoothly when the battery is connected to the front vertical motor connector terminals.

OK:
Measurement Condition Operational Direction
Battery positive (+) → 4 (UP)
Battery negative (-) → 1 (DOWN)
Seat cushion spring moves upward
Battery positive (+) → 1 (DOWN)
Battery negative (-) → 4 (UP)
Seat cushion spring moves downward




OK

6.CHECK HARNESS AND CONNECTOR (FRONT POWER SEAT SWITCH - FRONT VERTICAL MOTOR)

NG

REPLACE SEPARATE TYPE FRONT SEAT CUSHION SPRING ASSEMBLY (FRONT VERTICAL MOTOR)

6.CHECK HARNESS AND CONNECTOR (FRONT POWER SEAT SWITCH - FRONT VERTICAL MOTOR)

*1: for LHD

*2: for RHD


a.

Disconnect the b4*1 or a4*2 switch connector.


b.

Disconnect the b2*1 or a2*2 motor connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for LHD
Tester Connection Condition Specified Condition
b4-8 (FRV+) - b2-4 (UP) Always Below 1 Ω
b4-5 (FRV-) - b2-1 (DOWN) Always Below 1 Ω
b4-8 (FRV+) - Body ground Always 10 kΩ or higher
b4-5 (FRV-) - Body ground Always 10 kΩ or higher

for RHD
Tester Connection Condition Specified Condition
a4-8 (FRV+) - a2-4 (UP) Always Below 1 Ω
a4-5 (FRV-) - a2-1 (DOWN) Always Below 1 Ω
a4-8 (FRV+) - Body ground Always 10 kΩ or higher
a4-5 (FRV-) - Body ground Always 10 kΩ or higher




OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR