When the front power seat switch does not receive a sensor signal despite upward or downward movement of the seat by power seat motor operation, this DTC is stored.
| DTC Code | DTC Detection Condition | Trouble Area |
|---|---|---|
| B2653 | The upward and downward lock detection position of the sensor is the same. | ·
Front power seat switch ·
Separate type front seat cushion spring assembly (Lifter motor) ·
Harness or connector |
Select the Active Test, use the intelligent tester to generate a control command, and then check the power seat motor function (See page Vehicle Interior>SEAT>FRONT POWER SEAT CONTROL SYSTEM (w/ Memory)>DATA LIST / ACTIVE TEST).
| Tester Display | Test Part | Control Range | Diagnostic Note |
|---|---|---|---|
| Lifter Operation | Seat lifter operation | Up / OFF / Down | - |
Motor operates normally.
OK
NG
Disconnect the b3*1 or a3*2 motor connector.
*1: for LHD
*2: for RHD
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| b3-2 (O/P) - b3-3 (GND) | Lifter switch on | 4.8 to 5.1 V |
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| a3-2 (O/P) - a3-3 (GND) | Lifter switch on | 4.8 to 5.1 V |
| *A | for LHD |
| *B | for RHD |
| *a | Front view of wire harness connector
(to Separate Type Front Seat Cushion Spring Assembly [Lifter Motor]) |
OK
NG
Connect the b3*1 or a3*2 motor connector.
*1: for LHD
*2: for RHD
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| b3-2 (O/P) - Body ground | Lifter switch on | 4.5 to 4.8 V |
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| a3-2 (O/P) - Body ground | Lifter switch on | 4.5 to 4.8 V |
| *A | for LHD |
| *B | for RHD |
| *a | Component with harness connected
(Separate Type Front Seat Cushion Spring Assembly [Lifter Motor]) |
OK
NG
*1: for LHD
*2: for RHD
Disconnect the b5*1 or a5*2 switch connector.
Disconnect the b3*1 or a3*2 motor connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| b5-4 (SSRL) - b3-2 (O/P) | Always | Below 1 Ω |
| b5-1 (SGND) - b3-3 (GND) | Always | Below 1 Ω |
| b5-4 (SSRL) - Body ground | Always | 10 kΩ or higher |
| b5-1 (SGND) - Body ground | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| a5-4 (SSRL) - a3-2 (O/P) | Always | Below 1 Ω |
| a5-1 (SGND) - a3-3 (GND) | Always | Below 1 Ω |
| a5-4 (SSRL) - Body ground | Always | 10 kΩ or higher |
| a5-1 (SGND) - Body ground | Always | 10 kΩ or higher |
OK
NG
Remove the separate type front seat cushion spring assembly (lifter motor) (See page Vehicle Interior>SEAT>FRONT SEAT ASSEMBLY (for Power Seat)>DISASSEMBLY).
Check if the seat cushion spring moves smoothly when the battery is connected to the lifter motor connector terminals.
| Measurement Condition | Operational Direction |
|---|---|
| Battery positive (+) → 1 (UP)
Battery negative (-) → 4 (DOWN) |
Seat cushion spring moves upward |
| Battery positive (+) → 4 (DOWN)
Battery negative (-) → 1 (UP) |
Seat cushion spring moves downward |
OK
NG
*1: for LHD
*2: for RHD
Disconnect the b4*1 or a4*2 switch connector.
Disconnect the b3*1 or a3*2 motor connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| b4-10 (LFT+) - b3-1 (UP) | Always | Below 1 Ω |
| b4-12 (LFT-) - b3-4 (DOWN) | Always | Below 1 Ω |
| b4-10 (LFT+) - Body ground | Always | 10 kΩ or higher |
| b4-12 (LFT-) - Body ground | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| a4-10 (LFT+) - a3-1 (UP) | Always | Below 1 Ω |
| a4-12 (LFT-) - a3-4 (DOWN) | Always | Below 1 Ω |
| a4-10 (LFT+) - Body ground | Always | 10 kΩ or higher |
| a4-12 (LFT-) - Body ground | Always | 10 kΩ or higher |
OK
NG