Home › Vehicle Interior › SEAT › FRONT POWER SEAT CONTROL SYSTEM (w/ Memory)
RM27T0E _58 Vehicle Interior _053737 SEAT _0261110 FRONT POWER SEAT CONTROL SYSTEM(w/ Memory) C

SEAT  FRONT POWER SEAT CONTROL SYSTEM(w/ Memory)  B2658  Short in Sensor with Motor Power Supply Circuit  


DESCRIPTION

This DTC is stored when a power seat motor operates (a position control sensor is being supplied with power) and the power supply voltage does not rise to the specified value.

DTC Code DTC Detection Condition Trouble Area
B2658 A problem with the voltage supplied to the position control sensor.
·

Front power seat switch

·

Separate type front seat cushion spring assembly

·

Separate type front seatback assembly

·

Harness or connector



WIRING DIAGRAM

B238259E05
1.354,1.26 2.219,1.438 0.865,0.177 10 false b1*1, a1*2 1.354,1.406 2.104,1.583 0.75,0.177 10 false Slide Motor 1.917,0.375 2.188,0.542 0.271,0.167 10 false O/P 5.219,0.938 5.688,1.104 0.469,0.167 10 false SGND 5.219,0.385 5.688,0.552 0.469,0.167 10 false SSRS 2.302,0.271 2.521,0.427 0.219,0.156 10 false 2 1.875,0.938 2.219,1.094 0.344,0.156 10 false GND 2.302,0.823 2.521,0.979 0.219,0.156 10 false 3 4.938,0.219 5.031,0.375 0.094,0.156 10 false 5 1.354,6.833 2.26,7.01 0.906,0.177 10 false f1*1, e1*2 1.354,7 2.354,7.177 1,0.177 10 false Reclining Motor 1.927,2.052 2.188,2.208 0.26,0.156 10 false O/P 5.219,6.125 5.688,6.292 0.469,0.167 10 false SSRR 2.302,1.948 2.521,2.104 0.219,0.156 10 false 2 1.875,2.448 2.219,2.604 0.344,0.156 10 false GND 2.302,2.323 2.521,2.479 0.219,0.156 10 false 3 4.896,5.958 5.073,6.115 0.177,0.156 10 false 11 1.354,2.771 2.26,2.948 0.906,0.177 10 false b2*1, a2*2 1.354,2.927 2.604,3.104 1.25,0.177 10 false Front Vertical Motor 1.938,3.563 2.219,3.719 0.281,0.156 10 false O/P 5.219,2.083 5.688,2.25 0.469,0.167 10 false SSFV 2.302,3.458 2.521,3.615 0.219,0.156 10 false 2 1.875,3.948 2.219,4.104 0.344,0.156 10 false GND 2.302,3.844 2.521,4 0.219,0.156 10 false 3 4.938,1.896 5.031,2.052 0.094,0.156 10 false 3 1.354,4.271 2.281,4.448 0.927,0.177 10 false b3*1, a3*2 1.354,4.458 2.104,4.635 0.75,0.177 10 false Lifter Motor 1.938,6.125 2.219,6.281 0.281,0.156 10 false O/P 5.219,3.573 5.688,3.74 0.469,0.167 10 false SSRL 2.302,6.01 2.521,6.167 0.219,0.156 10 false 2 1.875,6.51 2.219,6.667 0.344,0.156 10 false GND 2.302,6.406 2.521,6.563 0.219,0.156 10 false 3 4.938,3.396 5.031,3.552 0.094,0.156 10 false 4 0.083,8.198 0.823,8.385 0.74,0.188 10 false *1: for LHD 0.083,8.49 0.823,8.677 0.74,0.188 10 false *2: for RHD 4.938,0.771 5.031,0.927 0.094,0.156 10 false 1 0.781,5.052 2.958,5.396 2.177,0.344 10 false Separate Type Front Seat Cushion Spring Assembly 0.906,7.594 2.833,7.938 1.927,0.344 10 false Separate Type Front Seatback Assembly 4.938,7.573 6.5,7.74 1.563,0.167 10 false Front Power Seat Switch 4.906,0.396 5.083,0.552 0.177,0.156 10 false b5 4.917,0.563 5.063,0.719 0.146,0.156 10 false *1 4.563,0.396 4.74,0.552 0.177,0.156 10 false a5 4.604,0.208 4.698,0.365 0.094,0.156 10 false 5 4.604,1.896 4.698,2.052 0.094,0.156 10 false 3 4.604,3.396 4.698,3.552 0.094,0.156 10 false 4 4.604,0.771 4.698,0.927 0.094,0.156 10 false 1 4.552,0.563 4.698,0.719 0.146,0.156 10 false *2 4.917,1.125 5.063,1.281 0.146,0.156 10 false *1 4.573,1.125 4.719,1.281 0.146,0.156 10 false *2 4.917,2.24 5.063,2.396 0.146,0.156 10 false *1 4.573,2.24 4.719,2.396 0.146,0.156 10 false *2 4.917,3.75 5.063,3.906 0.146,0.156 10 false *1 4.573,3.75 4.719,3.906 0.146,0.156 10 false *2 4.917,6.313 5.063,6.469 0.146,0.156 10 false *1 4.573,6.313 4.719,6.469 0.146,0.156 10 false *2 4.563,5.958 4.74,6.115 0.177,0.156 10 false 11 4.906,0.938 5.083,1.094 0.177,0.156 10 false b5 4.563,0.938 4.74,1.094 0.177,0.156 10 false a5 4.906,2.073 5.083,2.229 0.177,0.156 10 false b5 4.563,2.063 4.74,2.219 0.177,0.156 10 false a5 4.906,3.573 5.083,3.729 0.177,0.156 10 false b5 4.563,3.573 4.74,3.729 0.177,0.156 10 false a5 4.906,6.135 5.083,6.292 0.177,0.156 10 false b5 4.563,6.135 4.74,6.292 0.177,0.156 10 false a5

PROCEDURE

1.CHECK FOR DTC

OK

NG

2.CHECK HARNESS AND CONNECTOR (FRONT POWER SEAT SWITCH - SLIDE MOTOR)
2.CHECK HARNESS AND CONNECTOR (FRONT POWER SEAT SWITCH - SLIDE MOTOR)

*1: for LHD

*2: for RHD


a.

Disconnect the b5*1 or a5*2 switch connector.


b.

Disconnect the b1*1 or a1*2 motor connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for LHD
Tester Connection Condition Specified Condition
b5-5 (SSRS) - b1-2 (O/P) Always Below 1 Ω
b5-1 (SGND) - b1-3 (GND) Always Below 1 Ω
b5-5 (SSRS) - b5-1 (SGND) Always 10 kΩ or higher
b5-5 (SSRS) - Body ground Always 10 kΩ or higher
b5-1 (SGND) - Body ground Always 10 kΩ or higher

for RHD
Tester Connection Condition Specified Condition
a5-5 (SSRS) - a1-2 (O/P) Always Below 1 Ω
a5-1 (SGND) - a1-3 (GND) Always Below 1 Ω
a5-5 (SSRS) - a5-1 (SGND) Always 10 kΩ or higher
a5-5 (SSRS) - Body ground Always 10 kΩ or higher
a5-1 (SGND) - Body ground Always 10 kΩ or higher




OK

3.CHECK FRONT POWER SEAT SWITCH (SLIDE MOTOR CIRCUIT)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK FRONT POWER SEAT SWITCH (SLIDE MOTOR CIRCUIT)
a.
U169720E01
0.139,0.104 0.312,0.274 0.173,0.169 10 *a 1.215,1.815 1.543,1.967 0.328,0.152 10 O/P 1.87,1.815 2.197,1.967 0.328,0.152 10 GND 1.581,1.355 1.37,1.681 1.37,1.681 1.37,1.798 false 1.853,1.355 2.064,1.681 2.064,1.681 2.064,1.798 false 0.633,0.818 0.812,0.975 0.179,0.158 10 *A 0.633,1.264 0.812,1.422 0.179,0.158 10 *B 0.341,0.966 0.524,1.123 0.183,0.157 10 b1 0.336,1.41 0.509,1.567 0.172,0.157 10 a1

Disconnect the b1*1 or a1*2 motor connector.

*1: for LHD

*2: for RHD



b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
for LHD
Tester Connection Switch Condition Specified Condition
b1-2 (O/P) - b1-3 (GND) Sliding switch on 4.8 to 5.1 V

for RHD
Tester Connection Switch Condition Specified Condition
a1-2 (O/P) - a1-3 (GND) Sliding switch on 4.8 to 5.1 V


Text in Illustration
*A for LHD
*B for RHD
*a Front view of wire harness connector
(to Separate Type Front Seat Cushion Spring Assembly [Slide Motor])



OK

4.CHECK HARNESS AND CONNECTOR (FRONT POWER SEAT SWITCH - FRONT VERTICAL MOTOR)

NG

4.CHECK HARNESS AND CONNECTOR (FRONT POWER SEAT SWITCH - FRONT VERTICAL MOTOR)

*1: for LHD

*2: for RHD


a.

Disconnect the b5*1 or a5*2 switch connector.


b.

Disconnect the b2*1 or a2*2 motor connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for LHD
Tester Connection Condition Specified Condition
b5-3 (SSFV) - b2-2 (O/P) Always Below 1 Ω
b5-1 (SGND) - b2-3 (GND) Always Below 1 Ω
b5-3 (SSFV) - b5-1 (SGND) Always 10 kΩ or higher
b5-3 (SSFV) - Body ground Always 10 kΩ or higher
b5-1 (SGND) - Body ground Always 10 kΩ or higher

for RHD
Tester Connection Condition Specified Condition
a5-3 (SSFV) - a2-2 (O/P) Always Below 1 Ω
a5-1 (SGND) - a2-3 (GND) Always Below 1 Ω
a5-3 (SSFV) - a5-1 (SGND) Always 10 kΩ or higher
a5-3 (SSFV) - Body ground Always 10 kΩ or higher
a5-1 (SGND) - Body ground Always 10 kΩ or higher




OK

5.CHECK FRONT POWER SEAT SWITCH (FRONT VERTICAL MOTOR CIRCUIT)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK FRONT POWER SEAT SWITCH (FRONT VERTICAL MOTOR CIRCUIT)
a.
U169722E01
0.139,0.104 0.312,0.274 0.173,0.169 10 *a 1.221,1.815 1.491,1.967 0.270,0.152 10 O/P 1.87,1.815 2.197,1.967 0.328,0.152 10 GND 1.581,1.355 1.37,1.681 1.37,1.681 1.37,1.798 false 1.853,1.355 2.064,1.681 2.064,1.681 2.064,1.798 false 0.633,0.818 0.812,0.975 0.179,0.158 10 *A 0.633,1.264 0.812,1.422 0.179,0.158 10 *B 0.336,0.965 0.511,1.119 0.174,0.154 10 b2 0.336,1.41 0.508,1.564 0.172,0.154 10 a2

Disconnect the b2*1 or a2*2 motor connector.

*1: for LHD

*2: for RHD



b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
for LHD
Tester Connection Switch Condition Specified Condition
b2-2 (O/P) - b2-3 (GND) Front vertical switch on 4.8 to 5.1 V

for RHD
Tester Connection Switch Condition Specified Condition
a2-2 (O/P) - a2-3 (GND) Front vertical switch on 4.8 to 5.1 V


Text in Illustration
*A for LHD
*B for RHD
*a Front view of wire harness connector
(to Separate Type Front Seat Cushion Spring Assembly [Front Vertical Motor])



OK

6.CHECK HARNESS AND CONNECTOR (FRONT POWER SEAT SWITCH - LIFTER MOTOR)

NG

6.CHECK HARNESS AND CONNECTOR (FRONT POWER SEAT SWITCH - LIFTER MOTOR)

*1: for LHD

*2: for RHD


a.

Disconnect the b5*1 or a5*2 switch connector.


b.

Disconnect the b3*1 or a3*2 motor connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for LHD
Tester Connection Condition Specified Condition
b5-4 (SSRL) - b3-2 (O/P) Always Below 1 Ω
b5-1 (SGND) - b3-3 (GND) Always Below 1 Ω
b5-4 (SSRL) - b5-1 (SGND) Always 10 kΩ or higher
b5-4 (SSRL) - Body ground Always 10 kΩ or higher
b5-1 (SGND) - Body ground Always 10 kΩ or higher

for RHD
Tester Connection Condition Specified Condition
a5-4 (SSRL) - a3-2 (O/P) Always Below 1 Ω
a5-1 (SGND) - a3-3 (GND) Always Below 1 Ω
a5-4 (SSRL) - a5-1 (SGND) Always 10 kΩ or higher
a5-4 (SSRL) - Body ground Always 10 kΩ or higher
a5-1 (SGND) - Body ground Always 10 kΩ or higher




OK

7.CHECK FRONT POWER SEAT SWITCH (LIFTER MOTOR CIRCUIT)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.CHECK FRONT POWER SEAT SWITCH (LIFTER MOTOR CIRCUIT)
a.
U169723E01
0.139,0.104 0.312,0.274 0.173,0.169 10 *a 1.22,1.815 1.488,1.967 0.268,0.152 10 O/P 1.87,1.815 2.197,1.967 0.328,0.152 10 GND 1.581,1.355 1.37,1.681 1.37,1.681 1.37,1.798 false 1.853,1.355 2.064,1.681 2.064,1.681 2.064,1.798 false 0.633,0.818 0.812,0.975 0.179,0.158 10 *A 0.633,1.264 0.812,1.422 0.179,0.158 10 *B 0.335,0.965 0.510,1.121 0.174,0.156 10 b3 0.335,1.41 0.510,1.567 0.174,0.156 10 a3

Disconnect the b3*1 or a3*2 motor connector.

*1: for LHD

*2: for RHD



b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
for LHD
Tester Connection Switch Condition Specified Condition
b3-2 (O/P) - b3-3 (GND) Lifter switch on 4.8 to 5.1 V

for RHD
Tester Connection Switch Condition Specified Condition
a3-2 (O/P) - a3-3 (GND) Lifter switch on 4.8 to 5.1 V


Text in Illustration
*A for LHD
*B for RHD
*a Front view of wire harness connector
(to Separate Type Front Seat Cushion Spring Assembly [Lifter Motor])



OK

8.CHECK SEPARATE TYPE FRONT SEAT CUSHION SPRING ASSEMBLY

NG

8.CHECK SEPARATE TYPE FRONT SEAT CUSHION SPRING ASSEMBLY
a.

Temporarily replace the separate type front seat cushion springs one at a time with a new or normally functioning one (See page Vehicle Interior>SEAT>FRONT SEAT ASSEMBLY (for Power Seat)>DISASSEMBLY).



c.

Check for DTCs (See page Vehicle Interior>SEAT>FRONT POWER SEAT CONTROL SYSTEM (w/ Memory)>DTC CHECK / CLEAR).

OK:

DTC B2658 is not output.




OK

END (REPLACE SEPARATE TYPE FRONT SEAT CUSHION SPRING ASSEMBLY)

NG

9.CHECK HARNESS AND CONNECTOR (FRONT POWER SEAT SWITCH - RECLINING MOTOR)
9.CHECK HARNESS AND CONNECTOR (FRONT POWER SEAT SWITCH - RECLINING MOTOR)

*1: for LHD

*2: for RHD


a.

Disconnect the b5*1 or a5*2 switch connector.


b.

Disconnect the f1*1 or e1*2 motor connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for LHD
Tester Connection Condition Specified Condition
b5-11 (SSRR) - f1-2 (O/P) Always Below 1 Ω
b5-1 (SGND) - f1-3 (GND) Always Below 1 Ω
b5-11 (SSRR) - b5-1 (SGND) Always 10 kΩ or higher
b5-11 (SSRR) - Body ground Always 10 kΩ or higher
b5-1 (SGND) - Body ground Always 10 kΩ or higher

for RHD
Tester Connection Condition Specified Condition
a5-11 (SSRR) - e1-2 (O/P) Always Below 1 Ω
a5-1 (SGND) - e1-3 (GND) Always Below 1 Ω
a5-11 (SSRR) - a5-1 (SGND) Always 10 kΩ or higher
a5-11 (SSRR) - Body ground Always 10 kΩ or higher
a5-1 (SGND) - Body ground Always 10 kΩ or higher




OK

10.CHECK FRONT POWER SEAT SWITCH (RECLINING MOTOR CIRCUIT)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

10.CHECK FRONT POWER SEAT SWITCH (RECLINING MOTOR CIRCUIT)
a.
U169721E01
0.139,0.104 0.312,0.274 0.173,0.169 10 *a 1.22,1.815 1.487,1.967 0.267,0.152 10 O/P 1.87,1.815 2.197,1.967 0.328,0.152 10 GND 1.581,1.355 1.37,1.681 1.37,1.681 1.37,1.798 false 1.853,1.355 2.064,1.681 2.064,1.681 2.064,1.798 false 0.633,0.818 0.812,0.975 0.179,0.158 10 *A 0.633,1.264 0.812,1.422 0.179,0.158 10 *B 0.365,0.962 0.501,1.118 0.136,0.156 10 f1 0.333,1.411 0.505,1.567 0.172,0.156 10 e1

Disconnect the f1*1 or e1*2 motor connector.

*1: for LHD

*2: for RHD



b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
for LHD
Tester Connection Switch Condition Specified Condition
f1-2 (O/P) - f1-3 (GND) Reclining switch on 4.8 to 5.1 V

for RHD
Tester Connection Switch Condition Specified Condition
e1-2 (O/P) - e1-3 (GND) Reclining switch on 4.8 to 5.1 V


Text in Illustration
*A for LHD
*B for RHD
*a Front view of wire harness connector
(to Separate Type Front Seatback Assembly [Reclining Motor])



OK

11.CHECK SEPARATE TYPE FRONT SEATBACK ASSEMBLY

NG

11.CHECK SEPARATE TYPE FRONT SEATBACK ASSEMBLY
a.

Temporarily replace the separate type front seatbacks one at a time with a new or normally functioning one (See page Vehicle Interior>SEAT>FRONT SEAT ASSEMBLY (for Power Seat)>DISASSEMBLY).



c.

Check for DTCs (See page Vehicle Interior>SEAT>FRONT POWER SEAT CONTROL SYSTEM (w/ Memory)>DTC CHECK / CLEAR).

OK:

DTC B2658 is not output.




OK

END (REPLACE SEPARATE TYPE FRONT SEATBACK ASSEMBLY)

NG