Home › Vehicle Interior › SEAT › REAR POWER SEAT CONTROL SYSTEM
RM27T0E _58 Vehicle Interior _053737 SEAT _0261112 REAR POWER SEAT CONTROL SYSTEM J

SEAT  REAR POWER SEAT CONTROL SYSTEM  Parking Brake Switch Circuit  


DESCRIPTION

This circuit includes the parking brake switch assembly and fold seat control ECU.

WIRING DIAGRAM

B239924E01
2.004,1.201 2.459,1.396 0.455,0.195 10 G77 2.004,1.39 4.004,1.566 2.000,0.176 10 Parking Brake Switch Assembly 5.021,2.165 6.479,2.512 1.458,0.347 10 Fold Seat Control ECU LH*1, RH*2 4.954,0.878 5.128,1.028 0.174,0.150 10 d1 4.624,0.878 4.789,1.028 0.165,0.150 10 c1 4.961,1.059 5.113,1.216 0.152,0.158 10 *1 4.627,1.059 4.778,1.216 0.152,0.158 10 *2 4.952,0.696 5.126,0.853 0.174,0.158 10 40 4.617,0.696 4.791,0.853 0.174,0.158 10 40 5.266,0.878 5.648,1.033 0.382,0.155 10 PKB1 3.256,0.769 3.355,0.927 0.099,0.158 10 1 0.164,2.087 1.212,2.245 1.048,0.159 10 *1: for LH Side 0.164,2.397 1.212,2.556 1.048,0.159 10 *2: for RH Side

PROCEDURE

1.CHECK BRAKE WARNING LIGHT
a.

Check that the brake warning light comes on when the parking brake is applied and goes off when the parking brake is released.

OK:

The brake warning light operates as specified above.




OK

2.CHECK HARNESS AND CONNECTOR (FOLD SEAT CONTROL ECU - PARKING BRAKE SWITCH)

NG

3.INSPECT PARKING BRAKE SWITCH ASSEMBLY
2.CHECK HARNESS AND CONNECTOR (FOLD SEAT CONTROL ECU - PARKING BRAKE SWITCH)
a.

Disconnect the d1*1 or c1*2 ECU connector.

*1: for LH Side

*2: for RH Side



b.

Disconnect the G77 parking brake switch connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for LH Side
Tester Connection Condition Specified Condition
d1-40 (PKB1) - G77-1 Always Below 1 Ω
d1-40 (PKB1) - Body ground Always 10 kΩ or higher

for RH Side
Tester Connection Condition Specified Condition
c1-40 (PKB1) - G77-1 Always Below 1 Ω
c1-40 (PKB1) - Body ground Always 10 kΩ or higher




OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.INSPECT PARKING BRAKE SWITCH ASSEMBLY
a.
E194874E02
2.239,0.78 2.575,1.004 0.336,0.224 10 Off 2.239,0.355 2.491,0.580 0.252,0.224 10 On

Remove the parking brake switch assembly (See page Brake>PARKING BRAKE>PARKING BRAKE SWITCH>REMOVAL).


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1 - Switch body On (Shaft is not pressed) Below 1 Ω
1 - Switch body Off (Shaft is pressed) 10 kΩ or higher




OK

NG

REPLACE PARKING BRAKE SWITCH ASSEMBLY