Wear protective gloves. Sharp areas on the parts may injure your hands.
71695C
1.INSTALL REAR NO. 1 SEAT PROTECTOR RH
Attach the claw to install the protector.
71695B
2.INSTALL REAR NO. 1 SEAT PROTECTOR LH
Attach the 2 claws to install the protector.
73310A
3.INSTALL NO. 1 SEAT 3 POINT TYPE BELT ASSEMBLY RH
73187A
4.INSTALL REAR SEAT SHOULDER BELT GUIDE
Attach the guide and claw to install the belt guide.
71697
5.INSTALL REAR SEATBACK EDGE PROTECTOR
Install the protector to the seatback frame.
71077S
6.INSTALL SEPARATE TYPE REAR SEATBACK COVER RH
Using hog ring pliers, install the seatback cover to the seatback pad with new hog rings.
| *1 | Hog Ring Pliers |
Be careful not to damage the cover.
When installing the hog rings, avoid wrinkling the cover.
7.INSTALL SEATBACK COVER WITH PAD
Connect the outer belt to the seatback cover with pad.
Attach the hook.
| *1 | Hog Ring Pliers |
| *2 | Hook |
| *3 | Hog Ring |
Using hog ring pliers, install the seatback cover with pad with new hog rings.
72613B
8.INSTALL REAR SEAT LOCK STRIKER
Using a T45 "TORX" socket wrench, install the striker.
72618
9.INSTALL REAR SEATBACK LOCK STRIKER PROTECTOR
Install the protector to the striker.
73373
10.INSTALL REAR SEAT SHOULDER BELT COVER
Connect the outer belt to the cover.
Attach the 3 claws to install the cover.
Install the screw.
73178A
11.INSTALL SEAT BELT ANCHOR COVER CAP
Attach the 2 guides and 2 claws to install the cap.
71931B
12.INSTALL REAR NO. 1 SEAT HEADREST SUPPORT ASSEMBLY
Attach the 4 claws to install the 2 supports.
72646
13.INSTALL REAR SEATBACK STOP BUTTON GROMMET
Attach the 3 claws to install the grommet.
72661C
14.INSTALL REAR SEATBACK LOCK RELEASE BUTTON
Install the release button as shown in the illustration.
|
Clockwise |
72630C
15.INSTALL REAR SEATBACK LOCK ASSEMBLY RH
While moving the release button in the direction of the arrow in the illustration, attach it to the grommet.
Install the seatback lock with the 2 bolts.
Using hog ring pliers, install 2 new hog rings.
| *1 | Hog Ring Pliers |
72665
16.INSTALL REAR SEATBACK LOCK COVER RH
Attach the 2 hooks to install the cover.
Install the 2 screws.
72978
17.INSTALL CENTER NO. 2 SEATBACK COVER
Attach the 2 claws to install the cover.
Install the screw.
72067
18.INSTALL REAR BACK LOCK CONTROL LEVER SUB-ASSEMBLY RH
Install the control lever with the 2 screws.
72650A
19.INSTALL REAR SEAT LOCK ASSEMBLY RH
Install the lock with the 2 bolts.
Attach the clamp to connect the wire.
71413
20.INSTALL REAR NO. 1 SEAT NO. 2 SIDE PLATE
Attach the 3 claws to install the plate.
Install the 2 screws.
71931A
21.INSTALL REAR SEAT HEADREST SUPPORT
Attach the 4 claws to install the 2 supports.
71087
22.INSTALL REAR SEATBACK BOARD SUB-ASSEMBLY
Attach the 4 claws and 3 clips to install the board.
72665B
23.INSTALL REAR SEATBACK LOCK COVER
Move the cover in the direction of the arrow to attach the clip and 2 guides.
Attach the claw.
72996A
24.INSTALL REAR SEATBACK COVER
Attach the 4 claws to install the cover.
66990B
25.INSTALL NO. 2 CUP HOLDER ASSEMBLY RH
Install the 2 cup holders.
72830
26.INSTALL REAR CENTER SEAT ARMREST ASSEMBLY
Install the bush.
Using a T45 "TORX" socket wrench, install the armrest and 2 bushes with the 2 "TORX" bolts.
71349B
27.INSTALL REAR SEATBACK STAY COVER RH
Attach the 3 claws to install the cover.
Using a T45 "TORX" socket wrench, install the bush and hinge with the "TORX" bolt.
71369B
28.INSTALL REAR SEATBACK STAY COVER LH
Attach the 3 claws to install the cover.
71397A
29.INSTALL CENTER SEAT HINGE COVER
Attach the claw to install the cover.
71960B
30.INSTALL REAR CENTER SEAT HEADREST ASSEMBLY
Install the headrest.
31.INSTALL CENTER SEATBACK ASSEMBLY
Temporarily install the center seatback with the 2 bolts, bush and "TORX" bolt.
Tighten the 2 bolts.
Using a T45 "TORX" socket wrench, tighten the "TORX" bolt.
71095S
32.INSTALL CENTER SEATBACK COVER SUB-ASSEMBLY
Attach the 2 guides and install the cover with the screw.
73460C
33.INSTALL REAR SEAT CENTER INNER BELT ASSEMBLY
71879A
34.INSTALL REAR SEAT INNER RECLINING COVER RH
Attach the 2 guides and install the cover with the screw.
79109
35.INSTALL NO. 1 SEATBACK BOARD SUB-ASSEMBLY
Attach the guide and 3 clips to install the board.
79959
36.INSTALL REAR SEAT LEG COVER
Attach the guide and claw to install the cover.
Use the same procedure for both covers.
79956
37.INSTALL REAR SEAT LEG BRACKET COVER
Attach the 4 claws to install the cover.
Use the same procedure for both covers.
71393
38.INSTALL REAR SEAT CUSHION BAND
Install the band as shown in the illustration.
71075S
39.INSTALL SEPARATE TYPE REAR SEAT CUSHION COVER RH
Using hog ring pliers, install the seat cushion cover to the seat cushion pad with new hog rings.
| *1 | Hog Ring Pliers |
Be careful not to damage the cover.
When installing the hog rings, avoid wrinkling the cover.
79117B
40.INSTALL NO. 1 SEAT CUSHION COVER RH
Install the cover to the seat cushion pad with new tack pins.
41.INSTALL SEAT CUSHION COVER WITH PAD
Attach the hooks to install the seat cushion cover with pad.
Connect the seat cushion band to the seat cushion cover.
72927
42.INSTALL REAR SEAT CUSHION UNDER COVER RH
Attach the hooks to install the cover.
71695
43.INSTALL REAR SEATBACK PROTECTOR
Attach the 2 hooks to install the protector.
Install the 2 screws.
71324B
44.INSTALL REAR SEAT CUSHION
Install the 2 cushions with the 2 screws.