Home › Vehicle Interior › SEAT › REAR NO. 1 SEAT ASSEMBLY (for 60/40 Split Slide Walk-in Seat Type RH Side) › 2015.06–2021.06
RM27T0E _58 Vehicle Interior _053737 SEAT _0261119 REAR NO. 1 SEAT ASSEMBLY(for 60/40 Split Slide Walk-in Seat Type RH Side) A

SEAT  REAR NO. 1 SEAT ASSEMBLY(for 60/40 Split Slide Walk-in Seat Type RH Side)  DISASSEMBLY  


CAUTION / NOTICE / HINT

CAUTION:

Wear protective gloves. Sharp areas on the parts may injure your hands.


HINT:
·

Use the same procedure for RHD and LHD vehicles.

·

The procedure listed below is for LHD vehicles.



PROCEDURE

Hide 71845A 1.REMOVE REAR SEAT UPPER RECLINING COVER RH

B237712E01
1.596,1.847 1.826,2.040 0.230,0.193 10 *1 1.55,1.921 1.384,1.921 1.384,1.921 0.955,1.59 false

a.

Using a screwdriver, detach the 3 claws and remove the rear seat upper reclining cover RH.

HINT:

Tape the screwdriver tip before use.


Text in Illustration
*1 Protective Tape


Hide 72525B 2.REMOVE RECLINING ADJUSTER RELEASE HANDLE RH

B237713

a.

Remove the 3 screws and reclining adjuster release handle RH.


Hide 71825B 3.REMOVE REAR SEAT CUSHION MOULDING RH

B237716

a.

Using a clip remover, detach the clip.


b.

Using a moulding remover, detach the 3 claws.


c.

Move the rear seat cushion moulding RH in the direction of the arrow to detach the guide and remove the rear seat cushion moulding RH.


Hide 71829B 4.REMOVE REAR SEAT REAR CUSHION MOULDING LH

B237799

a.

Remove the screw.


b.

Using a moulding remover, detach the 3 claws.


c.

Detach the 2 guides and remove the rear seat rear cushion moulding LH.


Hide 72615A 7.REMOVE REAR SEATBACK LOCK STRIKER COVER RH

B237718

a.

Using a clip remover, detach the 3 clips and remove the rear seatback lock striker cover RH.


Hide 8.REMOVE SEAT CUSHION COVER WITH PAD

a.
B359311

w/ Seat Heater System:

i.

Disconnect the 2 rear seat heater connectors.


ii.
B360129

Pull out the wire harness as shown in the illustration.



b.
B237909

Detach the hooks and remove the seat cushion cover with pad.


Hide 71696 9.REMOVE REAR NO. 2 SEAT PROTECTOR

B237723

a.

Remove the 2 rear No. 2 seat protectors from the separate type rear seat cushion pad.


Hide 71647 10.REMOVE REAR SEAT CUSHION EDGE PROTECTOR

a.

Remove the rear seat cushion edge protector from the cushion spring.


Hide 71075S 11.REMOVE SEPARATE TYPE REAR SEAT CUSHION COVER

B237911

a.

Remove the 14 hog rings and separate type rear seat cushion cover from the separate type rear seat cushion pad.


Hide 87510P 12.REMOVE REAR SEAT CUSHION HEATER ASSEMBLY (w/ Seat Heater System)

Hide 72572B 13.REMOVE RECLINING ADJUSTER KNOB CAP RH

a.
B237754E01
0.679,0.935 0.840,1.104 0.161,0.168 10 *1 0.857,1.015 0.953,1.015 0.953,1.015 1.24,1.816 false

Using a screwdriver, detach the claw and guide, and then remove the reclining adjuster knob cap RH.

HINT:

Tape the screwdriver tip before use.


Text in Illustration
*1 Protective Tape


Hide 72057 14.REMOVE REAR SEAT LOCK CONTROL LEVER SUB-ASSEMBLY RH

a.
B237756

Remove the 2 screws.


b.
B165052E06
0.552,1.188 0.802,1.406 0.25,0.219 10 false (1) 1.021,2.156 1.271,2.344 0.25,0.188 10 true (2) 1.177,2.938 1.427,3.125 0.25,0.188 10 false (3)

Disconnect the cable in the order shown in the illustration and remove the rear seat lock control lever sub-assembly RH.


Hide 71845C 15.REMOVE REAR SEAT COVER CAP

B237913

a.

Using a screwdriver, detach the claw and guide, and then remove the rear seat cover cap.

HINT:

Tape the screwdriver tip before use.



Hide 72067A 16.REMOVE REAR CENTER BACK LOCK CONTROL LEVER

B237965

a.

Remove the 2 screws.


b.

Move the rear center back lock control lever in the direction of the arrow to detach the guide and remove the rear center back lock control lever.


c.

Detach the cable clamp and disconnect the cable from the rear center back lock control lever.


Hide 72996A 17.REMOVE REAR SEATBACK COVER

B237641

a.

Using a screwdriver, detach the 4 claws and remove the rear seatback cover.

HINT:

Tape the screwdriver tip before use.



Hide 71880A 18.REMOVE REAR SEATBACK BOARD CARPET ASSEMBLY RH

B237915

a.

Using a clip remover, detach the 7 clips and remove the rear seatback board carpet assembly RH.


Hide 71931B 19.REMOVE REAR NO. 1 SEAT HEADREST SUPPORT ASSEMBLY

B237672

a.

Detach the 4 claws and remove the 2 rear No. 1 seat headrest support assemblies.


Hide 20.REMOVE SEATBACK COVER WITH PAD

a.
B237916E01
1.692,0.051 1.866,0.244 0.174,0.193 10 *1 1.892,0.131 2.058,0.131 2.058,0.131 2.714,0.404 false 2.058,0.131 2.917,0.286 false 2.918,1.524 3.092,1.716 0.174,0.193 10 *2 2.181,1.624 2.9,1.624 false 2.058,0.131 2.27,1.011 false

Remove the 14 hog rings and detach the hooks, and then remove the seatback cover with pad.

Text in Illustration
*1 Hook
*2 Hog Ring


b.

w/ Seat Heater System:

i.
B360128

Remove the wire harness.



Hide 71077S 21.REMOVE SEPARATE TYPE REAR SEATBACK COVER

a.
B248337

w/ Seat Heater System:

i.

Disconnect the rear seatback heater assembly wire harness from the separate type rear seatback pad.



b.
B241213

Remove the 8 hog rings and separate type rear seatback cover from the separate type rear seatback pad.


Hide 87510Q 22.REMOVE REAR SEATBACK HEATER ASSEMBLY (w/ Seat Heater System)

Hide 71697 23.REMOVE REAR SEATBACK EDGE PROTECTOR

a.

Remove the rear seatback edge protector from the rear seatback frame sub-assembly RH.


Hide 71879C 24.REMOVE REAR SEAT INNER RECLINING COVER RH

B237920

a.

Remove the 2 screws.


b.

Detach the guide and remove the rear seat inner reclining cover RH.


Hide 71875J 25.REMOVE RECLINING ADJUSTER INSIDE COVER RH

B237770

a.

Remove the 2 screws.


b.

Detach the 2 claws and remove the reclining adjuster inside cover RH.


Hide 71876C 26.REMOVE RECLINING ADJUSTER INSIDE COVER RH

B237918

a.

Using a clip remover, detach the clip.


b.

Move the reclining adjuster inside cover RH in the direction of the arrow to detach the 2 claws and remove the reclining adjuster inside cover RH.


Hide 71875E 27.REMOVE RECLINING ADJUSTER INSIDE COVER RH

B237919

a.

Detach the claw and guide, and remove the reclining adjuster inside cover RH.


Hide 71499C 28.REMOVE REAR SEAT CUSHION SPRING DAMPER

B237967

a.

Remove the 2 nuts and rear seat cushion spring damper.


Hide 71499D 29.REMOVE REAR SEATBACK SPRING DAMPER (w/ Dynamic Damper)

a.
B295840

Remove the 2 nuts and rear seatback spring damper.


Hide 72704A 30.REMOVE REAR SEAT RECLINING CONTROL CABLE

a.

Cut off the 3 cable ties.

B237921


b.

Detach the 2 cable clamps and disconnect the rear seat reclining control cable, and then remove the rear seat reclining control cable.

B237922


Hide 72704B 31.REMOVE REAR NO. 2 SEAT RECLINING CONTROL CABLE

a.

Detach the cable clamp and disconnect the rear No. 2 seat reclining control cable, and then remove the rear No. 2 seat reclining control cable.

B237923


Hide 87501D 32.REMOVE SEAT HEATER CONTROL SUB-ASSEMBLY (w/ Seat Heater System)

Hide 82193 33.REMOVE REAR SEAT WIRE RH (w/ Seat Heater System)

a.
B249861

Detach the claw and disconnect the rear seat wire connector.


b.

Detach the clamp and remove the rear seat wire RH.


Hide 71246A 34.REMOVE REAR SEAT CUSHION SET PLATE

B237924

a.

Remove the 2 nuts and rear seat cushion set plate.


Hide 72631 35.REMOVE REAR SEATBACK LOCK PLATE LH

a.

Detach the 2 cable clamps and disconnect the cable.


b.

Remove the nut and rear seatback lock plate LH.

B237925


Hide 71017 36.REMOVE REAR SEATBACK FRAME SUB-ASSEMBLY RH

B237926

a.

Using a T45 "TORX" socket wrench, remove the 4 "TORX" bolts and rear seatback frame sub-assembly RH.


Hide 72995A 37.REMOVE REAR SEAT COVER

B237927

a.

Remove the screw and rear seat cover.


Hide 71461 38.REMOVE REAR SEAT CUSHION SPRING

B237928

a.

Detach the 2 hooks and remove the rear seat cushion spring.


Hide 71015A 39.REMOVE REAR SEAT CUSHION FRAME SUB-ASSEMBLY RH

B237932E01
1.549,0.084 1.720,0.245 0.171,0.162 10 *1 1.743,0.164 1.909,0.164 1.909,0.164 2.14,0.574 false

a.

Remove the 6 nuts and rear seat cushion frame sub-assembly RH together with the No. 1 seat leg plate.

Text in Illustration
*1 No. 1 Seat Leg Plate


Hide 72173A 40.REMOVE REAR SEAT TRACK ADJUSTING HANDLE RH

a.
B237929

Remove the seat cushion side frame sub-assembly RH.


b.
B237930

Slide the slide rail to the rearmost position.


c.

Using a small screwdriver, push down the handle stopper to detach the claw and remove the rear seat track adjusting handle RH.

HINT:

Insert the screwdriver in the hole shown into the illustration while looking into the hole.