Wear protective gloves. Sharp areas on the parts may injure your hands.
Use the same procedure for RHD and LHD vehicles.
The procedure listed below is for LHD vehicles.
Use the same procedure for the RH and LH sides.
The procedure listed below is for the RH side.
1.INSTALL FRONT SEAT SIDE AIRBAG ASSEMBLY (w/ Front Seat Side Airbag)
71873
2.INSTALL FRONT SEAT LOWER CUSHION SHIELD RH
Install the cushion shield with the screw.
72991
3.INSTALL FRONT SEAT CUSHION COVER RH
Install the cover with the screw.
71551S
4.INSTALL SEPARATE TYPE FRONT SEATBACK PAD
Install the seatback pad.
87510M
5.INSTALL FRONT SEATBACK HEATER ASSEMBLY RH (w/ Seat Heater System)
71073S
6.INSTALL SEPARATE TYPE FRONT SEATBACK COVER
Using hog ring pliers, install the seatback cover to the seatback pad with new hog rings.
Be careful not to damage the cover.
When installing the hog rings, avoid wrinkling the cover.
The number of hog rings differs according to seat type.
| *A | for Type A | *B | for Type B |
| *1 | Hog Ring Pliers | - | - |
Attach the 4 claws to install the 2 headrest supports.
w/ Front Seat Side Airbag:
Connect the seatback cover bracket to the seatback pad.
Install the seatback cover bracket to the seat frame with the nut.
After the seatback trim cover is assembled, make sure the side airbag strap is not twisted.
Close the 2 fasteners, and then close the seatback cover.
| *A | for Cloth Seat | *B | for Leather Seat |
Using hog ring pliers, install 3 new hog rings.
| *1 | Hog Ring Pliers |
71876C
7.INSTALL RECLINING ADJUSTER INSIDE COVER LH
Move the cover in the direction of the arrow to install the cover.
Attach the guide.
71875K
8.INSTALL RECLINING ADJUSTER INSIDE COVER RH
Use the same procedure described for the LH side.
82191
9.INSTALL FRONT SEAT WIRE RH
Install the seat wire.
87501A
10.INSTALL SEAT HEATER CONTROL SUB-ASSEMBLY RH (w/ Seat Heater System)
71537D
11.INSTALL FRONT SEAT CUSHION EDGE PROTECTOR LH
Move the protector in the direction of the arrow to attach the hook and 2 guides and install the protector.
| *1 | Hook |
| *2 | Guide |
Install the screw.
71537C
12.INSTALL FRONT SEAT CUSHION EDGE PROTECTOR RH
Move the protector in the direction of the arrow to attach the hook and guide and install the protector.
| *1 | Hook |
| *2 | Guide |
Attach the clip.
Install the screw.
87510K
13.INSTALL FRONT SEAT CUSHION HEATER ASSEMBLY RH (w/ Seat Heater System)
71071S
14.INSTALL SEPARATE TYPE FRONT SEAT CUSHION COVER
Using hog ring pliers, install the seat cushion cover to the seat cushion pad with new hog rings.
| *1 | Hog Ring Pliers |
Be careful not to damage the cover.
When installing the hog rings, avoid wrinkling the cover.
15.INSTALL SEAT CUSHION COVER WITH PAD
Install the seat cushion cover with pad.
Attach the claw to connect the connector.
Install the clip.
w/ Seat Heater System:
Connect the seat heater connector and attach the 3 wire harness clamps.
62476E
16.INSTALL CAP
Install the 2 caps.
71430S
17.INSTALL SEPARATE TYPE FRONT SEATBACK ASSEMBLY
Install the seatback assembly with the 4 bolts.
Attach the hook.
Attach the cable clamp to connect the cable.
w/ Front Seat Side Airbag:
Connect the airbag wire harness.
Attach the fastening tape to close the cover.
Attach the 3 airbag wire harness clamps.
Attach the claw and connect the airbag connector.
w/ Seat Heater System:
Connect the seat heater connector and attach the wire harness clamp.
Install the rubber band to the seat cushion spring.
73230
18.INSTALL FRONT SEAT INNER BELT ASSEMBLY RH
71861
19.INSTALL FRONT SEAT INNER CUSHION SHIELD RH
Attach the 5 claws to install the cushion shield.
71811D
20.INSTALL FRONT SEAT CUSHION SHIELD RH
Attach the cable clamp.
Attach the 2 clips and 5 claws to install the cushion shield.
Install the screw.
72525B
21.INSTALL RECLINING ADJUSTER RELEASE HANDLE RH
Attach the claw to install the handle.