Wear protective gloves. Sharp areas on the parts may injure your hands.
Use the same procedure for RHD and LHD vehicles.
The procedure listed below is for LHD vehicles.
71537C
1.INSTALL FRONT SEAT CUSHION EDGE PROTECTOR RH
Clean the front seat frame assembly with adjuster RH surface.
Install a new front seat cushion edge protector RH as shown in the illustration.
71537D
2.INSTALL FRONT SEAT CUSHION EDGE PROTECTOR
Install the 2 front seat cushion edge protectors.
72497
3.INSTALL OUTER VERTICAL ADJUSTER BRACKET COVER
Attach the claw to install the outer vertical adjuster bracket cover.
Install the screw.
71876
4.INSTALL RECLINING ADJUSTER OUTSIDE COVER LH
Install the reclining adjuster outside cover LH with the screw.
71875A
5.INSTALL RECLINING ADJUSTER OUTSIDE COVER RH
Use the same procedure described for the LH side.
71876A
6.INSTALL RECLINING ADJUSTER INSIDE COVER LH
Attach the guide to install the reclining adjuster inside cover LH.
Install the screw.
71875B
7.INSTALL RECLINING ADJUSTER INSIDE COVER RH
Use the same procedure described for the LH side.
71861
8.INSTALL FRONT SEAT INNER CUSHION SHIELD RH
Attach the hook and claw to install the front seat inner cushion shield RH.
Install the 2 screws.
71397A
9.INSTALL CENTER SEAT HINGE COVER
Attach the guide to install the center seat hinge cover.
Install the screw.
10.INSTALL FRONT SEATBACK PROTECTOR
Remove any double-sided tape remaining on the front seat frame assembly with adjuster RH.
Apply double-sided tape as shown in the illustration.
| *1 | Double-sided Tape |
Install the front seatback protector.
71551S
11.INSTALL SEPARATE TYPE FRONT SEATBACK PAD
Install the separate type front seatback pad to the front seat frame assembly with adjuster RH.
71073S
12.INSTALL SEPARATE TYPE FRONT SEATBACK COVER
Using hog ring pliers, install the separate type front seatback cover to the separate type front seatback pad with new hog rings.
Be careful not to damage the cover.
When installing the hog rings, avoid wrinkling the cover.
Attach the 4 claws to install the 2 front seat headrest supports.
Attach the fastening tape and hook.
| *1 | Hog Ring Pliers | *2 | Hog Ring |
| *3 | Hook | *4 | Fastening Tape |
Using hog ring pliers, attach the 2 straps of the separate type front seatback cover to the front seat frame assembly with adjuster RH with new hog rings.
| *1 | Hog Ring Pliers |
Using hog ring pliers, attach the separate type front seatback cover with new hog rings.
Be careful not to damage the cover.
When installing the hog rings, avoid wrinkling the cover.
| *1 | Hog Ring Pliers |
71071S
13.INSTALL SEPARATE TYPE FRONT SEAT CUSHION COVER
Using hog ring pliers, install the separate type front seat cushion cover to the separate type front seat cushion pad with new hog rings.
Be careful not to damage the cover.
When installing the hog rings, avoid wrinkling the cover.
| *1 | Hog Ring Pliers |
| *2 | Tack pin |
Using a tacker, install the separate type front seat cushion cover to the separate type front seat cushion pad with a new tack pin as shown in the illustration.
Attach the hook.
| *1 | Hook |
| *2 | Hog Ring |
| *3 | Hog Ring Pliers |
Using hog ring pliers, install the separate type front seat cushion cover to the separate type front seat cushion pad with new hog rings.
When installing the hog rings, avoid wrinkling the cover.
82666M
14.INSTALL CONNECTOR HOLDER
Attach the claw to install the connector holder.
15.INSTALL FRONT SEAT CUSHION COVER WITH PAD
Set the front seat cushion cover with pad in place.
Attach the 2 clamps to install the connector holder.
Attach the hooks to install the front seat cushion cover with pad.
Using hog ring pliers, install new hog rings.
Be careful not to damage the cover.
When installing the hog rings, avoid wrinkling the cover.
Install the clip.
| *1 | Hog Ring Pliers | *2 | Hog Ring |
Return the 2 cushion edge tabs to their original positions.
Be careful not to break the cushion edge tabs.
71081S
16.INSTALL FRONT SEATBACK SIDE COVER SUB-ASSEMBLY RH
Install the front seatback side cover sub-assembly RH to the front seatback inside pad RH.
Install the front seatback side cover sub-assembly RH with the front seatback inside pad RH.
Attach the hook to close the front seatback side cover sub-assembly RH.
71847A
17.INSTALL FRONT SEAT ARMREST HOLE BOARD COVER
Install the front seat armrest hole board cover to the seat armrest assembly RH.
72880
18.INSTALL SEAT ARMREST ASSEMBLY RH
Install the seat armrest assembly RH with the bolt.
71270
19.INSTALL INNER SEAT BRACKET ASSEMBLY RH
Install the inner seat bracket assembly RH with the 4 bolts.
Lift up the seat armrest assembly RH and place it in the normal seating position.
71873
20.INSTALL FRONT SEAT LOWER CUSHION SHIELD RH
Attach the hook to install the front seat lower cushion shield RH.
Install the 2 screws.
71831D
21.INSTALL FRONT SEAT HINGE COVER RH
Attach the 2 hooks to install the front seat hinge cover RH.
Install the 2 screws.
71274
22.INSTALL FRONT SEAT HINGE KNOB
Twist the front seat hinge knob in the direction indicated by the arrow to install it.
71811D
23.INSTALL FRONT SEAT CUSHION SHIELD RH
Attach the guide and clip.
Attach the claw and hook to install the front seat cushion shield RH.
| *1 | Guide |
| *2 | Hook |
Install the screw.
Attach the 2 rubber bands.
72525A
24.INSTALL RECLINING ADJUSTER RELEASE HANDLE RH
Attach the claw to install the reclining adjuster release handle RH.
73240
25.INSTALL FRONT SEAT INNER BELT ASSEMBLY RH
71848A
26.INSTALL SEAT ADJUSTER COVER CAP RH
Install the 2 seat adjuster cover caps.