Home › Vehicle Interior › HEATING / AIR CONDITIONING › AIR CONDITIONING SYSTEM (for Automatic Air Conditioning System)
RM27T0E _58 Vehicle Interior _053739 HEATING / AIR CONDITIONING _0261169 AIR CONDITIONING SYSTEM(for Automatic Air Conditioning System) C

HEATING / AIR CONDITIONING  AIR CONDITIONING SYSTEM(for Automatic Air Conditioning System)  B1413/13  Evaporator Temperature Sensor Circuit  


DESCRIPTION

The No. 1 cooler thermistor is installed on the evaporator in the air conditioning unit to detect the temperature of the cooled air that has passed through the evaporator and control the air conditioning. It sends appropriate signals to the air conditioning amplifier assembly. The resistance of the No. 1 cooler thermistor changes in accordance with the temperature of the cooled air that has passed through the evaporator. As the temperature decreases, the resistance increases. As the temperature increases, the resistance decreases.

The air conditioning amplifier assembly applies voltage (5 V) to the No. 1 cooler thermistor and reads voltage changes as the resistance of the No. 1 cooler thermistor changes. This sensor is used for frost prevention.

DTC Code DTC Detection Condition Trouble Area
B1413/13 An open or short in the No. 1 cooler thermistor circuit.
·

No. 1 cooler thermistor

·

Air conditioning harness assembly

·

Air conditioning amplifier assembly



WIRING DIAGRAM

E140288E53
4.635,2 4.865,2.156 0.229,0.156 10 false z1 4.646,2.188 7.063,2.479 2.417,0.292 10 false Air Conditioning Amplifier Assembly 4.896,0.708 5.26,0.854 0.365,0.146 10 false TEA 4.896,1.594 5.396,1.74 0.5,0.146 10 false SGA 4.604,0.573 4.75,0.792 0.146,0.219 10 false 6 2.406,1.438 2.552,1.656 0.146,0.219 10 false 1 2.417,0.573 2.563,0.792 0.146,0.219 10 false 2 4.604,1.438 4.75,1.656 0.146,0.219 10 false 5 0.677,1.99 2.281,2.167 1.604,0.177 10 false No. 1 Cooler Thermistor 2.75,2.021 4.271,2.365 1.521,0.344 10 false Air Conditioning Harness Assembly

PROCEDURE

1.READ VALUE USING INTELLIGENT TESTER (NO. 1 COOLER THERMISTOR)
a.

Use the Data List to check if the No. 1 cooler thermistor is functioning properly (See page Vehicle Interior>HEATING / AIR CONDITIONING>AIR CONDITIONING SYSTEM (for Automatic Air Conditioning System)>DATA LIST / ACTIVE TEST).

Air Conditioner
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
Evaporator Fin Thermistor No. 1 cooler thermistor /
Min.: -29.7°C (-21.46°F)
Max.: 59.55°C (139.19°F)
Actual evaporator temperature displayed Open in the circuit: -29.7°C (-21.46°F).
Short in the circuit: 59.55°C (139.19°F).

OK:

The display is as specified in the normal condition column.



Result
Result Proceed to
OK (When troubleshooting according to problem symptoms table) A
OK (When troubleshooting according to the DTC) B
NG C


A

B

REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY

C

2.INSPECT NO. 1 COOLER THERMISTOR
2.INSPECT NO. 1 COOLER THERMISTOR
a.

Remove the No. 1 cooler thermistor (See page Vehicle Interior>HEATING / AIR CONDITIONING>FRONT EVAPORATOR TEMPERATURE SENSOR>REMOVAL).

E346095E01
0.146,1.531 0.313,1.198 0.313,1.198 0.646,1.198 true 4.083,1.333 4.25,1 4.25,1 4.583,1 true 0.698,1.104 1.01,1.302 0.313,0.198 10 false *a 4.646,0.906 4.958,1.104 0.313,0.198 10 false *c 3.167,0.385 3.552,0.583 0.385,0.198 10 false 10.0 3.24,0.552 3.625,0.75 0.385,0.198 10 false 9.0 3.24,0.729 3.625,0.927 0.385,0.198 10 false 8.0 3.24,0.917 3.625,1.115 0.385,0.198 10 false 7.0 3.24,1.094 3.625,1.292 0.385,0.198 10 false 6.0 3.24,1.26 3.625,1.458 0.385,0.198 10 false 5.0 3.25,1.448 3.635,1.646 0.385,0.198 10 false 4.0 3.25,1.625 3.635,1.823 0.385,0.198 10 false 3.0 3.25,1.802 3.635,2 0.385,0.198 10 false 2.0 3.25,1.99 3.635,2.188 0.385,0.198 10 false 1.0 3.25,2.156 3.635,2.354 0.385,0.198 10 false 0.0 3.396,2.281 3.781,2.479 0.385,0.198 10 false -10 3.396,2.438 3.781,2.635 0.385,0.198 10 false (14) 4.01,2.281 4.396,2.479 0.385,0.198 10 false 0 4.521,2.438 4.906,2.635 0.385,0.198 10 false (50) 4.542,2.281 4.927,2.479 0.385,0.198 10 false 10 3.948,2.438 4.333,2.635 0.385,0.198 10 false (32) 5.104,2.281 5.49,2.479 0.385,0.198 10 false 20 5.073,2.438 5.458,2.635 0.385,0.198 10 false (68) 5.656,2.271 6.042,2.469 0.385,0.198 10 false 30 5.625,2.427 6.01,2.625 0.385,0.198 10 false (86) 4.354,2.573 4.667,2.771 0.313,0.198 10 false *d 3,1.219 3.313,1.417 0.313,0.198 10 false *b 3.198,0.177 3.615,0.375 0.417,0.198 10 false (kΩ) 6.063,2.271 6.646,2.469 0.583,0.198 10 false °C (°F)


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1 - 2 -10°C (14°F) 7.30 to 9.10 kΩ
-5°C (23°F) 5.65 to 6.95 kΩ
0°C (32°F) 4.40 to 5.35 kΩ
5°C (41°F) 3.40 to 4.15 kΩ
10°C (50°F) 2.70 to 3.25 kΩ
15°C (59°F) 2.14 to 2.58 kΩ
20°C (68°F) 1.71 to 2.05 kΩ
25°C (77°F) 1.38 to 1.64 kΩ
30°C (86°F) 1.11 to 1.32 kΩ


Text in Illustration
*a Sensing Portion
*b Resistance
*c Allowable Range
*d Temperature

NOTICE:
·

Even slightly touching the sensor may change the resistance value. Be sure to hold the connector of the sensor.

·

When measuring, the sensor temperature must be the same as the ambient temperature.



HINT:

As the temperature increases, the resistance decreases (refer to the graph).




OK

3.INSPECT AIR CONDITIONING HARNESS ASSEMBLY

NG

3.INSPECT AIR CONDITIONING HARNESS ASSEMBLY
a.
E346096E01
0.5,2.333 1,2.583 0.5,0.25 1.083,3.083 1.333,3.083 1.333,3.083 1.5,2.75 true 2,3.083 1.75,3.083 1.75,3.083 1.667,2.75 true 0.052,0.073 0.365,0.271 0.313,0.198 10 false *a 0.073,1.667 0.385,1.865 0.313,0.198 10 false *b 0.667,2.365 0.979,2.563 0.313,0.198 10 false z1 0.74,3 1.094,3.198 0.354,0.198 10 false SGA 2.052,2.99 2.406,3.188 0.354,0.198 10 false TEA

Remove the air conditioning harness assembly (See page Vehicle Interior>HEATING / AIR CONDITIONING>FRONT AIR CONDITIONING UNIT>DISASSEMBLY).


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
z1-6 (TEA) - 2 Always Below 1 Ω
z1-5 (SGA) - 1 Always Below 1 Ω
z1-6 (TEA) - Body ground Always 10 kΩ or higher
z1-5 (SGA) - Body ground Always 10 kΩ or higher


Text in Illustration
*a Front view of wire harness connector
(to No. 1 Cooler Thermistor)
*b Front view of wire harness connector
(to Air Conditioning Amplifier Assembly)



OK

REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY

NG